Instruction/ maintenance manual of the product G6200 Zenoah
Go to page of 16
G6200 G B GB-1 G6200 OWNER’S MANUAL CHAIN SA W G B 848C9F93A0 (807).
G6200 GB-2 EXPLANA TION OF SYMBOLS AND SAFETY W ARNINGS Read operator's instruction book before operating this machine. W ear head, e ye and ear protection. Use the chain saw with two hands. Wa r ning! Danger of kickback. Read, understand and follow all warnings.
G6200 G B GB-3 Contents 1. For Safe Operation ................................................................... 4 2. Explanation of Symbols on the Machine .................................. 6 3. Installing Guide Bar and Saw Chain ...................
G6200 GB-4 10. Keep all parts of your body away from the saw chain when the engine is run- ning. 11. Before you start the engine, make sure the saw chain is not contacting anything. 12. Always carry the chain saw with the engine stopped, the guide bar and saw chain to the rear , and the muffler away from your body .
G6200 G B GB-5 (3) Make certain that the area in which you are cutting is fr ee from obstruc- tions. Do not let the nose of the guide bar contact a log, branch, or any other obstruction which could be hit while you are operating the saw . (4) Cut at high engine speeds.
G6200 GB-6 2. Explanation of Symbols on the Machine W ARNING • For safe operation and maintenance, symbols are car ved in relief on the machine. According to these indications, please be careful not to make any mistake. The screw under the “H” stamp is The High-speed adjustment scr ew .
G6200 G B GB-7 5. Fit the chain cover to the power unit and fasten the nuts to finger tightness. 6. While holding up the tip of the bar , adjust the chain tension by turning the tensioner screw until the tie straps just touch the bottom side of the bar rail.
G6200 GB-8 4. Fuel and Chain Oil ■ FUEL W ARNING • Gasoline is very flammable. A void smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool bef ore refuel- ing the unit. Select outdoor bare ground f or fuel- ing and move at least 3 m (10 ft) a way fr om the fueling point before starting the engine.
G6200 G B GB-9 7. Allow the engine to warm up with the throttle lever pulled slightly . W ARNING •K eep clear of the sa w chain as it will start rotating upon starting of engine . ■ CHECKING THE OIL SUPPL Y W ARNING • Make sure to set up the bar and the chain when c hec king the oil supply .
G6200 GB-10 ■ ICING PREVENTION SYSTEM This system prevents icing of the carbur etor which some- times happen while sawing in winter . When your saw has stopped or slowed down abruptly , use the system as follows: 1. Remove the air cleaner cover , air filter , and silencer .
G6200 G B GB-11 6. Sawing • Before pr oceeding to your job, read the section “For Safe Op- eration”. It is recommended to first practice sa wing easy logs. This also helps you get accus- tomed to your unit. •A lwa ys follo w the safety regu- lations.
G6200 GB-12 A log lying on the gr ound Saw down halfway , then roll the log over and cut from the opposite side. A log hanging off the ground In area A, saw up fr om the bottom one-third and finish by sawing down from the top. In ar ea B, saw down from the top one-third and finish by sawing up fr om the bot- tom.
G6200 G B GB-13 ■ PERIODICAL SER VICE POINTS 1. Cylinder fins Dust clogging between the cylinder fins will cause overheat- ing of the engine. Periodically check and clean the cylinder fins after removing the air cleaner and the cylinder cover .
G6200 GB-14 W ARNING • This saw is equipped with one of the f ollowing low kickbac k bar/chain combinations: Zenoah Part Number Bar Size Guide Bar Saw Chain 16 3670-52112 848CC3LG60 (73LGX) 18 3673-.
G6200 G B GB-15 9. T r oubleshooting Guide Case 1. Starting failure W ARNING • Make sure the icing prevention system is not w orking. 11. Specifications Power unit: Displacement (cm 3 ): ............................................. 62.0 Fuel: .....
G6200 GB-16 Limited warranty Should any failure occur on the pr oduct under normal operating conditions within the applicable warranty pe- riod, the failed part will be replaced or repair ed free of charge by a ZENOAH authorized dealer .
An important point after buying a device Zenoah G6200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Zenoah G6200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Zenoah G6200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Zenoah G6200 you will learn all the available features of the product, as well as information on its operation. The information that you get Zenoah G6200 will certainly help you make a decision on the purchase.
If you already are a holder of Zenoah G6200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Zenoah G6200.
However, one of the most important roles played by the user manual is to help in solving problems with Zenoah G6200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Zenoah G6200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
