Instruction/ maintenance manual of the product G3300 Zenoah
Go to page of 16
G3300 / G3300EZ GB-1 G B G3300 G3300EZ OWNER’S MANUAL CHAINSA WS G B 848C3593A1 (411).
G3300 / G3300EZ GB-2 EXPLANA TION OF SYMBOLS AND SAFETY W ARNINGS Read operator's instruction book bef ore operating this machine. W ear head, ey e and ear protection. Use the chain saw with two hands. Wa r ning! Danger of kickbac k. Read, understand and f ollow all w arnings.
G3300 / G3300EZ GB-3 G B Contents 1. For Safe Operation ................................................................... 4 2. Explanation of Symbols on the Machine .................................. 6 3. Installing Guide Bar and Saw Chain .........
G3300 / G3300EZ GB-4 1. For safe operation 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medica- tion that may make you drowsy , or if you are under the influence of alcohol or drugs. 2. Use safety footwear , snug fitting clothing and eye, hearing and head protection devices.
G3300 / G3300EZ GB-5 G B move the clutch, structural dam- age to the flywheel could occur which could subsequently cause the flywheel to disintegrate.) 16.
G3300 / G3300EZ GB-6 [G3300] 1. Pull the guard towar ds the front handle to check that the chain brake is not engaged. 2. Loosen the nut and remove the chain cover . 3. Gear the chain to the sprocket and, while fitting the saw chain around the guide bar , mount the guide bar to the power unit.
G3300 / G3300EZ GB-7 G B [G3300EZ] 1. Pull the guard towar ds the front handle to check that the chain brake is not engaged. 2. Loosen the nut assembly and dismount the chain cover .
G3300 / G3300EZ GB-8 ■ RECOMMENDED MIXING RA TIO GASOLINE 50 : OIL 1 • Exhaust emission are controlled b y the funda- mental engine parameters and components (eq., carburation, ignition timing and port timing) with- out addition of an y major hard ware or the intro- duction of an inert material during combustion.
G3300 / G3300EZ GB-9 G B Do not start the engine while the chain saw hangs in one hand. The saw chain may touch your body . This is ver y danger ous. 6. When engine has ignited, pull the throttle slightly to r eturn the choke knob to the original position.
G3300 / G3300EZ GB-10 The carburetor on your unit has been factory adjusted, but may requir e fine tuning due to a change in operat- ing conditions. Before adjusting the carbur etor , make sure that the pr o- vided air/fuel filters are clean and fr esh and the fuel prop- erly mixed.
G3300 / G3300EZ GB-11 G B gine at full speed. If the chain is slow to stop or does not stop, replace the brake band and clutch drum before use. • It is extremely important that the chain brake be checked for proper operation before each use and that the chain be sharp in order to main- tain the kickback safety level of this saw .
G3300 / G3300EZ GB-12 Before cleaning, the inspecting or r epairing the unit, make sure that engine has stopped and is cool. Disconnect the spark plug to pre- vent accidental starting. ■ MAINTENANCE AFTER EA CH USE 1. Oiling port Dismount the guide bar and check the oiling port for clogging.
G3300 / G3300EZ GB-13 G B 2. Fuel filter Using a wire hook, take out the filter fr om the filler port. Clean away the dirt attached to the filter . Replace with a new one if needed. Note: Never bend the filter pipe when returning it. 3. Spark plug Clean the electrodes with a wir e brush and reset the gap to 0.
G3300 / G3300EZ GB-14 side of a cutter . If a gap is observed between them, the rail is normal. Otherwise, the bar rail is wor n. Such a bar needs to be corrected or r eplaced.
G3300 / G3300EZ GB-15 G B 9. T r oubleshooting Guide Case 1. Starting failure Make sure the icing pr evention system is not working. Check fuel for water or substandard mix- ture. Replace with proper fuel. Check for engine flooding. Check spark ignition.
G3300 / G3300EZ GB-16 Limited warranty Should any failure occur on the pr oduct under nor mal operating conditions within the applicable warranty pe- riod, the failed part will be replaced or repair ed free of charge by a KOMA TSU ZENOAH authorized dealer .
An important point after buying a device Zenoah G3300 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Zenoah G3300 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Zenoah G3300 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Zenoah G3300 you will learn all the available features of the product, as well as information on its operation. The information that you get Zenoah G3300 will certainly help you make a decision on the purchase.
If you already are a holder of Zenoah G3300, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Zenoah G3300.
However, one of the most important roles played by the user manual is to help in solving problems with Zenoah G3300. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Zenoah G3300 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
