Instruction/ maintenance manual of the product G300TS Zenoah
Go to page of 28
OWNER / OPERA T OR MANUAL CHAINSA WS 2875-93111(005) The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. W ARNING Before using our products, please read this manual carefully to understand the proper use of your unit.
.
SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.
2. Specifications ■ G310TS Power unit : Dis placement ····················································································· 1.
3. Symbols on the machine ❲ 5 ❳ Made in Japan RedMax IMPORT ANT ENGINE INFORMA TION THIS ENGINE CONFORMS TO US EP A PH1 AND 1995-1998 CALIFORNIA EMISSION REGULA TIONS FOR ULGE ENGINES. ENGINE F AMIL Y : TKZ030UB24RA ENGINE DISPLACEMENT : 30.1cc USE UNLEADED GASOLINE + AIR – COOLED 2 – CYCLE ENGINE OIL.
❲ 6 ❳ 4. For safe operation 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may make you drowsy, or if you are under the influence of alcohol or drugs. 2. Use safety footwear, snug fitting clothing and eye, hearing and head protection devices.
❲ 7 ❳ 4. For safe operation 1 6 . Operate the chain saw only in well ventilated areas. Never start or run the engine inside a closed room or building. Exhaust fumes contain dangerous carbon monoxide. 1 7 . Do not operate a chain saw in a tree unless specially trained to do so.
A standard saw unit package contains the items as shown. (SE1) Open the box and install the guide bar and the saw chain to the power unit as follows. The saw chain has very sharp edges. Use thick, protective gloves to avoid injury. 1. Loosen a nut and remove the chain cover.
6. Fuel and chain oil ❲ 9 ❳ ■ FUEL The RedMax engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If RedMax oil is not available, use an anti- oxidant added quality oil expressly labeled for air- cooled 2-cycle engine use.
6. Fuel and Chain oil ■ CHAIN OIL Use motor oil SAE 10W-30 all year round, or SAE 30-40 in summer and SAE 20 in winter. Do not use waste or regenerated oil that can cause damage to the oil pump.
■ FUELING THE UNIT (OP1) 1. Remove the fuel tank cap and pour fuel into the tank up to 80% of full capacity. 2. Fasten the fuel cap securely and wipe up any fuel spillage around the unit. 3. Remove the oil tank cap and pour chain oil into the tank. Fasten the cap securely.
❲ 12 ❳ OP8 7. Operation ■ CHECKING OIL SUPPLY After starting the engine, run the chain at medium speed and see if chain oil is scattered off as shown in the figure. (OP6) The oil tank should become nearly empty by the time fuel in the tank is used up.
so that saw chain does not turn. If idling speed is too slow, turn the screw clockwise. (OP8) 4 . Make a test cut adjust the H needle for best cutting power, not for maximum speed. (OP8) ■ CHAIN BRAKE The chain brake is a device designed to stop the saw chain quickly when kickback occured.
• Before proceeding to your job, read “For Safe Operation” section. It is recommended to first practice sawing easy logs. This also helps you get accustomed to your unit. • It is not necessary to force the saw into the cut. Apply only light pressure while running the engine at full throttle.
should stop immediately with the engine at full speed. If the chain is slow to stop or does not stop then replace the brake band and clutch drum before use. • It is extremely important that the chain brake be checked for proper operation before each use and that the chain be sharp in order to maintain the kickback safety level of this saw.
of bending direction to prevent the guide bar from being caught in the cutaway. ● Cutting an unpillowed log Saw down halfway, then roll the log over and cut from the opposite side. (SA3) ● Cutting a pillowed log In the area A in the picture right above, saw up from the bottom one-third and finish by sawing down from the top.
❲ 17 ❳ 9. Maintenance Make sure to stop the engine before inspecting and/or servicing the unit. ■ DAILY MAINTENANCE SAW CHAIN It is one of the essential factors for smooth and safe operation to keep the cutters always in good condition. It’s time to reform the cutters when; 1.
❲ 18 ❳ 9. Maintenance GUIDE BAR 1 . Remove sawdust in the bar groove and the oiling port. (MA5) 2. Grease the nose sprocket from the feeding port on the tip of the guide bar. (MA6) 3 . Periodically turn over the guide bar when mounting it to the unit, in order to prevent partial wear.
anything wrong be found, make sure to have it repaired before next usage. ■ MONTHLY MAINTENANCE FUEL FILTER When the engine runs short of fuel supply, check the fuel filter for blockage. (MA9) OIL STRAINER Drain the oil tank and remove the oil strainer located near the spark plug.
❲ 20 ❳ SPARK ARRESTER RedMax engines are equipped with a spark arresting screen at the exhaust port. Periodically check and keep it in good condition.
❲ 21 ❳ 1 1. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company.
❲ 22 ❳ 1 1. Parts list Fig.1 POWER UNIT G310TS (S/N 002191 and up) G310TS.
❲ 23 ❳ Fig.1 POWER UNIT (S/N 002191 and up) G310TS 1 2870-12111 CYLINDER 1 2 2633-15100 MUFFLER ASS’Y 1 3 2633-15110 • BASE 1 4 2633-15120 • COVER 1 5 2630-15130 • BUFFLE 1 6 2633-15150 .
❲ 24 ❳ 1 1. Parts list Fig.2 CARBBURETOR COMPONENTS & ACCESSORIES (S/N 002191 and up) G310TS.
❲ 25 ❳ Fig.2 CARBBURETOR COMPONENTS & ACCESSORIES (S/N 002191 and up) G310TS Key# PART NUMBER DESCRIPTION Q'TY /UNIT NOTE Key# PART NUMBER DESCRIPTION Q'TY /UNIT NOTE 1 2875-81001 CA.
THE CALIFORNIA AIR RESOURCES BOARD AND KOMATSU ZENOAH Co. ARE PLEASED TO EXPLAIN THE EMISSION CONTROL SYSTEM WARRANTY ON YOUR 1995 AND LATER LAWN AND GARDEN EQUIPMENT ENGINE. IN CALIFORNIA, NEW UTILITY AND LAWN AND GARDEN EQUIPMENT ENGINES MUST BE DESIGNED, BUILT AND EQUIPPED TO MEET THE STATE'S STRINGENT ANTI-SMOG STANDARDS.
EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE MODEL G310TS UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP.
© Printed in Japan Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratui.
An important point after buying a device Zenoah G300TS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Zenoah G300TS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Zenoah G300TS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Zenoah G300TS you will learn all the available features of the product, as well as information on its operation. The information that you get Zenoah G300TS will certainly help you make a decision on the purchase.
If you already are a holder of Zenoah G300TS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Zenoah G300TS.
However, one of the most important roles played by the user manual is to help in solving problems with Zenoah G300TS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Zenoah G300TS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
