Instruction/ maintenance manual of the product BC2403 Billy Goat
Go to page of 28
Part No 500402 1 Form No F020513A BILLY GOAT ® BC2403 Series Brush Cutter Owner’s Manual Patent Number D386768.
Part No 500402 2 F0 20513A BC2403 Series Brush Cutter Owner’s Manual CONTENTS Specifications and Sound/Vibration .................................................................................................................. 3 Instruction Labels .
Part No 500402 3 F0 20513A BC2403 Series Brush Cutter Owner’s Manual BC 2403 SERIES SPECIFICATIONS BC2403IC BC2403ICF BC2403HF BC2403H BC2403HEB Engine Type Briggs and Stratton INTEK OHV Briggs and Stratton INTEK OHV Honda GXV Honda GXV Honda GXV Model Number 21A902-0149- E1 21A902-0149- E1 GXV390UTIDABG GXV390UTIDABG GXV390K1DE33 Horsepower 13.
Part No 500402 4 F0 20513A BC2403 Series Brush Cutter Owner’s Manual INSTRUCTION LABELS The labels shown below were installed on your BILLY GOAT ® Brush Cu tter.
Part No 500402 5 F0 20513A BC2403 Series Brush Cutter Owner’s Manual Brush Cutter Assembly Drawin g Figure 1 100 22 Attach shifter to linkage here 202.
Part No 500402 6 F0 20513A BC2403 Series Brush Cutter Owner’s Manual ASSEMBLY INSTRUCTIONS Your BIL LY G OAT ® BC S elf -Propelled Brush Cutter was shipped in one carton, completely assembled except for the upper handle assembly an d the front guard bar.
Part No 500402 7 F0 20513A BC2403 Series Brush Cutter Owner’s Manual OPERATION O PERATOR C ONTROLS The operator’s station is at the rear of the machine between the handlebars. The operator should STAND in a position to allow both handlebars to be grasped firmly and which allows sufficient leverage to steer the machine.
Part No 500402 8 F0 20513A BC2403 Series Brush Cutter Owner’s Manual 4. Units equipped with electric starters: Pull up on the ON/OFF switch until engine starts. ON/OFF (I/O) (Manual start shown) DO NOT START equipment with drive or blade clutch engaged.
Part No 500402 9 F0 20513A BC2403 Series Brush Cutter Owner’s Manual 2. Press blade clutch handle down to engage blade. Allow blade to spin up to normal operating speed. Blade Clutch Lever 3. Pull drive clutch handle up to engage transaxle. Drive Clutch Lever S HUT D OWN 1.
Part No 500402 10 F0 20513A BC2403 Series Brush Cutter Owner’s Manual MAINTENANCE P ERIODIC M AINTENANCE Periodic maintenance should be perfo rmed at the following intervals: Maintenance Operation Every Use Daily or Every 5 Hours Every 25 Hours Every 50 Hours Every 100- 150 Hours Inspect for worn or damaged parts .
Part No 500402 11 F0 20513A BC2403 Series Brush Cutter Owner’s Manual B LADE R EMOVAL AND S HARPENING READ all safety instructions before servicing unit.
Part No 500402 12 F0 20513A BC2403 Series Brush Cutter Owner’s Manual B LADE D RIVE B ELT T ENSION A DJU STMENT READ all safety instructions before servicing unit. DISCONNECT spark plug wire before servicing unit. Numbers in parenthesis (N) refers to the item number in Illustrated Parts List.
Part No 500402 13 F0 20513A BC2403 Series Brush Cutter Owner’s Manual B LADE C LUTCH A DJUSTMENT READ all safety instructions before servicing unit. DISCONNECT spark plug wire before servicing unit.
Part No 500402 14 F0 20513A BC2403 Series Brush Cutter Owner’s Manual B LADE D RIVE B ELT R EMOVAL AND R EPLACEMENT READ all safety instructions before servicing unit.
Part No 500402 15 F0 20513A BC2403 Series Brush Cutter Owner’s Manual 12. Tighten four screws (103) to secure belt guides (149, 150). Make sure belt is correctly routed.
Part No 500402 16 F0 20513A BC2403 Series Brush Cutter Owner’s Manual T RANSAXLE D RIVE C LUTCH A DJUS TMENT READ all safety instructions before servicing unit.
Part No 500402 17 F0 20513A BC2403 Series Brush Cutter Owner’s Manual T RANSAXLE D RIVE B ELT R EMOVAL AND R EPLACEMENT READ all safety instructions before servicing unit. Numbers in parenthesis (N ) refers to the item number in Illustrated Parts List.
Part No 500402 18 F0 20513A BC2403 Series Brush Cutter Owner’s Manual W IRING D IAGRAMS Starter Switch Wiring Figure 3 Starter Circuit Schematic Diagra m Figure 4 ON/OFF Switch Circuit Schematic Dia.
Part No 500402 19 F0 20513A BC2403 Series Brush Cutter Owner’s Manual TROUBLESHOOTING Problem Possible Cause Corrective Action Engine will not start. ON/OFF switch is in OFF position. Move switch to START position. Out of gasoline. Fill gas tank. Old or contaminated gasoline.
Part No 500402 20 F0 20513A BC2403 Series Brush Cutter Owner’s Manual Battery Care (For Electric -Starting Models) Proper care can extend the life o f a battery. Follow these recommendations to ens ure your battery’s best performance and long life: • Do not allow the battery charge to get too low.
Part No 500402 21 F0 20513A BC2403 Series Brush Cutter Owner’s Manual ILLUSTRATED PARTS LIST Engine and Engine Base A ssembly Figure 6.
Part No 500402 22 F0 20513A BC2403 Series Brush Cutter Owner’s Manual ITEM NO DESCRIPTION BC2403 HEB BC2403H BC2403IC Part No QTY Part No QTY Part No QTY 4 Base Assembly with label s 500240 1 500240.
Part No 500402 23 F0 20513A BC2403 Series Brush Cutter Owner’s Manual Handlebar Assembly Figure 7.
Part No 500402 24 F0 20513A BC2403 Series Brush Cutter Owner’s Manual ITEM NO DESCRIPTION BC2403HEB BC2403H BC2403IC Part No QTY Part No QTY Part No QTY 5 Handle Brace Left 500196 1 500196 1 500196 .
Part No 500402 25 F0 20513A BC2403 Series Brush Cutter Owner’s Manual Transaxle and Blade Deck Assembly Figure 8.
Part No 500402 26 F0 20513A BC2403 Series Brush Cutter Owner’s Manual ITEM NO DESCRIPTION BC2403HEB BC2403H BC2403IC Part No QTY Part No QTY Part No QTY 1 Deck Assembly with Label s 500407 1 500407 1 500407 1 3 Deflector Front BC2402 500125 1 500125 1 500125 1 8 Transaxle 3 SPD BC2402 500365 1 500365 1 500365 1 9 Pulley 5.
Part No 500402 27 F0 20513A BC2403 Series Brush Cutter Owner’s Manual Blade Drive Spindle Assem bly Detail Drawing Figure 9.
Part No 500402 28 F0 20513A BC2403 Series Brush Cutter Owner’s Manual ITEM NO DESCRIPTION BC2403HEB BC2403H BC 2403IC Part No QTY Part No QTY Part No QTY 134 Spindle Assembly Complete 500242 1 50024.
An important point after buying a device Billy Goat BC2403 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Billy Goat BC2403 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Billy Goat BC2403 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Billy Goat BC2403 you will learn all the available features of the product, as well as information on its operation. The information that you get Billy Goat BC2403 will certainly help you make a decision on the purchase.
If you already are a holder of Billy Goat BC2403, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Billy Goat BC2403.
However, one of the most important roles played by the user manual is to help in solving problems with Billy Goat BC2403. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Billy Goat BC2403 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
