Instruction/ maintenance manual of the product 136, 141 Husqvarna
Go to page of 16
Instruction Manual Manuel d’instructions Betriebsanweisung Manual de instrucciones English Please read these instructions carefully make sure you understand them before using this unit. 530088185 1 1/1 1/02 Français A vant d’utiliser cet appareil, veuillez lire attentivement les instructions et assurez - - vous de les avoir comprises.
2 IDENTIFICATION (WHA T IS WHA T?) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 17 18 19 20 21 22 23 25 24 1. Cylinder Cov er 2. Front Handle 3. Front Handguard 4. Starter Cov er 5. Chain O il T ank 6. Starter Handl e 7. Carburator Adjus ting S crew 8. Choke Control 9.
3 SAFETY RULES W ARNING: Always dis connect spark plug wi re and place wire where it can- not contact spark plug to prev ent ac cidental starti ng when setting up, trans porting, ad- justi ng or maki ng repairs exc ept c arburetor adjustm ents.
4 S Mix and pour fuel in an outdoor area on bare ground; store fuel i n a cool, dry , well ventil ated plac e; and use an approv ed, marked container f or all fuel purposes. Wipe up all fuel spills before s tarting saw . S Move at least 10 f eet (3 meters ) from fuel- ing sit e before st arting engine.
5 Thumb on underside of handlebar Elbow loc ked S Keep a good, firm gri p on the saw with both hands when t he engine is running and don’t let go. A firm grip will help y ou reduc e kick back and mai ntain cont rol of the saw . Keep the fingers of your left hand encir- cling and y our left t humb under t he front handlebar .
6 SAFETY NOTICE: E xposure to vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and j oints of people prone to circulation d isorder s or abnormal sw ellings. Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people.
7 S Fit bott om of driv e links bet ween the teeth in the sprock et in the nose of t he guide bar. S Fit c hain drive links in bar groove. S Pull the bar forward until the chai n is snug in the guide bar groove. Ensure all drive links are in the bar groove.
8 T o stop the engine move the ON/STOP switc h to the STOP position. T o start the engine hold the saw firm ly on the ground as illustrat ed. Mak e s ure the chain is free to turn wit hout contac ting any object. Hold saw firmly while pulling starter rop e Use only 15” - - - 18” of rope per pull .
9 Braking functi on control CAUTION: The chain brake must be check ed sev eral tim es daily. T he engine must be running when perf orming thi s proce- dure. This i s the only instance when the saw should be placed on the ground with the en- gine running.
10 NOTCH CUT AND F ELLING THE TREE S Make notch cut by cutti ng t he top of t he notch first. Cut through 1/3 of the diam eter of the tree. Next com plete the not ch by cut- ting the bottom of the notch. See illustra- tion. Once the n otch is cut, remove th e notch of wood from the t ree.
11 Second cut First cut on compression side of log First cut on compression side of log Second cut BUCKING WITHOUT A SUPPORT S Overcut t hrough 1/3 of the diameter of the log. S Roll the l og over and f inish wit h a second overcut . S Watch for logs wit h a compression si de to prevent the s aw from pinching.
12 S Next make a 2nd cut all the way through the limb. Then cut a t hird overcut l eaving a 1 to 2 inch collar from the truc k of the tree. First cut Second cut Third cut Collar Pruning technique SERVICE W ARNING: Disconnec t the s park plug before performing maint enance exc ept for carburet or adjus tments.
13 S Before storing, drain all f uel from the uni t. Start engine and all ow to run until it stops. S Clean the unit before storing. Pay particular attenti on to the air intake area, keeping it free of debris. Use a mild detergent and sponge to clean th e plastic surfaces.
14 DECLARATION OF CONFORMIT Y relating to 2000/14/EC EU Declaration of Conformity relating to 2000/14/E C We, Poulan/ W eed Eater, Division Electrolux North America, I nc.
15 TECHNICAL D AT A S HEET Engine Cylinder v olume, c m 3 36 40 Stroke , mm 32 32 Idle speed, rpm 3,000 3,000 Recommended m ax. speed, unloaded, rpm 13,000 13, 000 Powe r, kW 1,6 1,9 Ignition system M.
We hope you find the links below useful. For further ga rdening information visit www.GardenResources.c o.uk Blower Vacs Brush cutters Brushcutters Chainsaws Chain saws Cultivators Cylinder lawn mower.
An important point after buying a device Husqvarna 136, 141 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna 136, 141 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna 136, 141 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna 136, 141 you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna 136, 141 will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna 136, 141, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna 136, 141.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna 136, 141. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna 136, 141 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
