Instruction/ maintenance manual of the product Transition Optic Wybron
Go to page of 19
TRANSI TION CMY Fiber Optic Illuminator CMY with TW -White light with WT -White light Transition User Manual.
2 Table of Contents Declaration of Conformity………………………………………………..3 Safety Notice………………………………………………………………4 Introducti.
3.
4 Safety Notice SAVE THESE INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS This manual gives step-by-step instructions for preparation, setup, and operation of the Transition TM Fiber Illuminator. There is a potential risk of fire, electric shock or injury to persons if the product is not used as instructed.
5.
6 Intro to the Transition.
7 Transition Product Introduction Wybron is pleased to announce the introduction of the Transition fiber illuminator. Contained within a small easy to integrate package and ultra bright fiber optic illuminator, the Transition brings quality and durability to your venue.
8 Transition Quick Start Configuration 1. Connect the Equipment a) Connect fiber bundle common end to the Transition output port. b) Connect the Transition to a DMX source with a 5-pin cable c) Connect to AC power (110 – 240 VAC 50/60Hz) 2.
9 Transition Specifications Model 8670: Transition CMY Fiber Illuminator Features: No lamp optimization required Rubber feet for cabinet or countertop installation Durable all metal construction Output supports fiber bundles ranging from 17 – 30 mm dia.
10 Fixture Setup and Configuration Installing the Lamp DANGER: Disconnect fixture from line voltage before replacing lamp. CAUTION: Lamp and lamp mounting surfaces are hot! Allow lamp to cool 10 minut.
11 Maximum ambient temperature (t a ) may not exceed 40˚C (104˚F) Keep objects at least 2” (50mm) from sides of the fixture. Keep objects at least 6” from the top of the fixture. Cabinet or Closet Mounting The Transition may be mounted in a closet or cabinet on a hard surface such as wood, laminate, or metal.
12 DMX / RDM Setup and Operation Controls and Indicators Transition controls and indicators as follows: o A three character seven-segment display o 4 push buttons: Menu , ( + ), ( - ), and Enter o Power (red) and signal (green) indicator LED’s The seven-segment display shows the address number (1-508) and the Demo mode (OFF, d1, d2).
13 Display Messages Normal Messages 680 Displayed for 1 second after power is applied. This is the RDM manufacturer device identification number Ini Indicates that the unit is initializing the diachronic filters 001 – 508 The first DMX address Transition will respond to.
14 EEP Err An attempt to write to non-volatile memory failed. The unit will continue to respond to commands. SEr Err The RDM unique ID has been corrupted. The unit will operate normally but should not be used in an RDM environment. Contact dealer or factory for assistance.
15 Service Lamp Replacement DANGER: Disconnect fixture from line voltage before replacing lamp. WARNING: Lamp and lamp mounting surfaces are hot! Allow lamp to cool before replacing. Disconnect fixture from AC power. Remove lamp plate by removing mounting screws as shown in figure 1.
16 Cleaning the Color Filters It is recommended that the color filters be only cleaned with low-pressure air without disassembling the color filters from the motor shafts. If the color module must be disassembled to clean the dichroic filters take careful note of the location and offset height of the individual color flags.
17 Flash Reprogramming Transition firmware can be updated as new firmware versions become available through the DMX/RDM port using an Infogate gateway and the Infogate application.
18 Warranty Information WYBRON, INC. warrants to the original owner or retail customer that for a period of one year from date of delivery of a portable system or energization of a permanently install.
19 Figure 2.1 Figure .2.
An important point after buying a device Wybron Transition Optic (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Wybron Transition Optic yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Wybron Transition Optic - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Wybron Transition Optic you will learn all the available features of the product, as well as information on its operation. The information that you get Wybron Transition Optic will certainly help you make a decision on the purchase.
If you already are a holder of Wybron Transition Optic, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Wybron Transition Optic.
However, one of the most important roles played by the user manual is to help in solving problems with Wybron Transition Optic. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Wybron Transition Optic along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
