Instruction/ maintenance manual of the product PTC20 Windsor
Go to page of 15
OPE~UIION Floor Scrubber WIN- INDUSTRIES, INC., 1351 W. Stanford Ave., Englewood, CO 80110 1 USA 303/762-1800 FAX 303/762-0817.
Operator Safety Instructions Read the instruction manual before operating this machine. Operate this machine only from the rear of machine. Use caution when operating the machine on a ramp or incline. Do not turn or leave this machine unattended on a ramp or incline.
‘I I‘ SQUEEGEE SOLUTION MAIN BATTERY SOLUTION VACUUM BRUSH SCRUB DECK LIFT LEVER CONTROL SWITCH CONOlTlON “ON” “ON” LIGHTED “ON” LIGHTED LIFT LEVER LEVER LIGHT LIGHT SWITCH SWITCH OPERATOR CONTROL HANDLE 1. Raises and lowers squeegee assembly.
MACHINE PREPARATION BATTERIES 1. Install batteries and connect battery cables as shown. WARNING: Provide proper ventilation, leave door open when charging batteries. 2. Charge the batteries before using the machine. (See Battery Charging Pro- ced u re) BRUSH/DRIVE PAD ASSEMBLY 1.
’ 3. Connect the “DC” charger plug to the connector on the machine. NOTE A safety override switch is activated when the “DC charge plug is connected. This prevents all panel circuits on the machine from accidentally being switched on during charging cycle.
SCRUB DECK/BRUSH MOTOR 1. Remove (4) screws holding motor shroud. 7. Squeegee tracking can be controlled by adjustin tension of squeegee springs. NOT% : Position recovery hose as shown before making adjustments. 2. Remove batteries and squeegee as - sembly.
TANKS, VAC & FRAME ' 27 39 12 It TANKS, VAC 6 FRAME KEY PART NO. DESCRIPTION 1 70020 Scr, 1/4 - 20 x 112 HHMS 2 61181 Panel, Rear 3 87090 Washer, 1/4 Flat 4 70010 Scr, 1/4 - 20 x 1.
SCRUB DECK 0 24 A0 ‘74 // 8 8.
I KEY PARTNO. DESCRIPTION 1A 73425 Strap Asm, PTC17 Bumper 1B 73465 Strap Asm, PTC20 Bumper 2 87090 Washer, 1/4 ID x 3/4 Flat 3 48012 Knob, Adjustment t 4A 14676 Bumper, PTC17 Brush Shroud 48 14571 Bumper, PTC20 Brush Shroud I 5A 02162 Pad Driver, 16 " Ylw Pad Lock 58 02156 Pad Driver Asm.
, ELECTRICAL CONTROLS 26 27 28 29 14 13 10.
I' MECHANICAL CONTROLS 34 A 14 - 3 28 I 13 41 12 1 t I. /" 30 I -@-- -3 1/36 37 ' 24 LJ 22 1- 32 I 8' MECHANICAL CONTROLS KEV PARTNO.
SQUEEGEE EL SQUEEOEE LIFT MECHANISM Frame r I 4? -I - Frame 4 KEY PART NO. OESCRIPTION 1 67103 Ring, 5/16 Ext Snap 2 87029 Washer, 5/16 Flat 3 89058 Wheel, Squeegee Roller 4 66108 Pin, Squeegee Wheel .
AUXILIARY PUMP MODEL 3 20 28 PLUMBING 27 STANDARD MODEL Note: Plumbing i I lus trated with machine laying on right side. 6 I 13.
TROUBLE - SHOOTING GUIDE PROBLEM PROBABLE CAUSE CORRECTIVE ACTION I No power. Battery cables corroded at battery terminals. Faulty main switch. Faulty safety override switch. 1. Clean battery cable clamps and battery terminals. 2. Check voltage at points A and B.
POWER SOLUTION SOLUTION LIGHT BATTERY LEVEL SWITCH SWITCH LIGHT VACWM/BRUSH SWITCH WIRING DIAGRAM VACUUM MOTOR PUMP SWITCH IOPTIONAL) e [ CHARGER CONNECTION I i al: PUMP MOTOR (OPTIONAL) PUMP Pump As.
An important point after buying a device Windsor PTC20 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Windsor PTC20 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Windsor PTC20 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Windsor PTC20 you will learn all the available features of the product, as well as information on its operation. The information that you get Windsor PTC20 will certainly help you make a decision on the purchase.
If you already are a holder of Windsor PTC20, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Windsor PTC20.
However, one of the most important roles played by the user manual is to help in solving problems with Windsor PTC20. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Windsor PTC20 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
