Instruction/ maintenance manual of the product D250 (115V) Windsor
Go to page of 20
Read these instructions before operating the machine MODEL: D250 (115V) Beginning with Serial No. 1000054537 98828 06/07/03 P CARPET EXTRACTOR Operating Instructions (ENG).
TABLE OF CONTENTS D- 250 98828 04/08/03 1 Data Log/Table of Contents ............... 1 Safety Instructions ............................. 2 Grounding Instructions ....................... 3 Operations .......................................... 4 Maintenance ………………………….
SAFETY INS TRUCTIONS D-250 98828 11/09/00 2 IMPORT ANT SA FETY INSTRUCTIONS When using an el ectrical ap pliance, bas ic precauti on must alw a y s be f ollow ed, including the foll owing: READ ALL INSTRUCTIONS BEFORE USING THIS M ACHINE. This machine i s for commerci al use.
GROUN DING INST RUCTI ONS D-250 98828 04/25/02 3 THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: The amp, hertz, and v oltage are list ed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious da mage to the motors.
OPERATIONS D- 250 98828 04/08/03 4 CARPET INSPECTION: Determine precisely what areas you are going to clean. Note problem areas in the carpet or tack strip. Look for loose carpet, heavily damaged areas, discolored stains, or grease spots that will require prespotting.
OPERATION D- 250 98828 04/08/03 5 HEATER OPERATION The disconnect fittings on the heater will become extremely hot during operation. Allow sufficient time to cool, or run solution through the machine with the heater turned off before disconnecting the or performing any maintenance on the heater.
MAINTENANCE D- 250 98828 04/08/03 6 DAILY MAINTENANCE: (At the end of each working day ) : 1.) Flush the entire system, including floor tool, hand tool, etc., with 1 to 3 gallons of clean, hot water. 2.) Vacuum out the solution tank . 3.) Rinse tank with fresh water.
MAINTENANCE D-250 98828 04/08/03 7 SERVICE SCHEDULE MAINTENANCE DAILY WEEKLY QUARTERLY Check machine for cord damage * Check recovery dome and gasket for damage and cleanliness * Check hoses for wear,.
MAINTENANCE D-250 98828 04/08/03 8 ! WARNING: ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS. VACUUM MOTOR REPLACEMENT 1. Turn off all switches and unplug machine. 2. Remove recovery tank. 3. Locate the vacuum motor wires and disconnect at the connector.
MAINTENANCE & TROUBLESHOOTING D- 250 98828 04/08/03 9 D-250 PUMP MAINTENANCE Per manufacturer’s recommendations the following maintenance should be performed utilizing noted kits: 1.) 500 hours-Kit 55250751 replaces the V-packing, wave washer, packing spreader and plunger guide.
TROUBLESHOOTING CONT. D-250 98828 04/08/03 10 Solution hose Corrosion on fittings Clean with steel wool. fitting hard to Soak in acetic acid (white vinegar). connect Lubricate lightly with silicone base lubricant. Carpet not Severe soil conditions Make several pass es at right angles to getting clean.
115V WIRING DIAGRAM D- 250 98828 06/07/03 11.
D-250 98828 04/08/03 12 THIS PAGE LEFT BLANK INTENTIONALLY.
RECOVERY TANK ASSEMBLY D- 250 98828 06/07/03 13 20 21 14 17 18 19 36 16 13 15 9 12 11 10 35 8 34 7 4 6 5 2 3 1 22 23 24 25 13 13 29 27 28 26 30 31 32 33.
RECOVERY TANK ASSEMBLY D- 250 98828 06/07/03 14 REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 05151 1 TUBE ASM, RECOVERY TANK 2 500009 1 LABEL, WARNING 3 260-64A 1 ACCESS COVER CLEAR 6” W/RI.
SOLUTION TANK ASSEMBLY D- 250 98828 06/07/03 15 12A 39 44 42 15 18 19 40 41 20 21 22 14 17 16 13 54 45 46 43 31 47 51 76 48 49 52 35 23 8 37 38 36 26A 27 30 28 24 25 31 34 29 33 32 11 10 31 9 8 7 6 5 .
SOLUTION TANK ASSEMBLY D- 250 98828 06/07/03 16 REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 85045 1 VAC MTR ASM, D/B SLTN 115V 2ST 2 39582 1 HOSE, VAC EXHAUST X 9” 3 20046 1 CLAMP, 2.
SOLUTION TANK ASSEMBLY CONT'. D- 250 98828 06/07/03 17 REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 54 70232 2 SCR, 10-32 X 3/8 FHMS SS 55 57196 2 NUT, 1/2 PUSH-ON DOME CAP 56 040-06 1 WHE.
Windsor Industries reserves the right to change its warranty policy without notice – Rev2 10 /16/02 1 WINDSOR INDUSTRI ES New M achine Warranty Limited Warranty Windsor Indu stries, Inc. warrants new machines against defects in material an d workmanship un der normal us e and service t o the original purchaser.
Windsor Industries reserves the right to change its warranty policy without notice – Rev2 10 /16/02 2 WINDSOR INDUSTRI ES New M achine Warranty 90 Day Warranty Ex tension Available Upon receipt of the Machine Registration Card, W indsor will extend by 90 days, from the date of purchase, all items included u n der the one-y ear provis ion.
An important point after buying a device Windsor D250 (115V) (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Windsor D250 (115V) yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Windsor D250 (115V) - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Windsor D250 (115V) you will learn all the available features of the product, as well as information on its operation. The information that you get Windsor D250 (115V) will certainly help you make a decision on the purchase.
If you already are a holder of Windsor D250 (115V), but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Windsor D250 (115V).
However, one of the most important roles played by the user manual is to help in solving problems with Windsor D250 (115V). Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Windsor D250 (115V) along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
