Instruction/ maintenance manual of the product CMPSR 10070080 Windsor
Go to page of 58
Operating Instructions (ENG) Read instructions before operating the machine. C 86290230 04/20/07 MODEL : CMPS 10070050 CMPSR 10070080 FROM SN: 1000170681.
MACHINE DATA LOG/OVERVIEW CMPS 86290230 02/22/07 2 YOUR DEALER Name: ________________ __________________________ __________________________ __________________________ ____ Address: __________________ .
TABLE OF CONTENTS CMPS 86290230 04/20/07 3 Machine Data Log/Overview. ........................ 1 Table of Contents .......................................... 2 HOW TO USE THIS MANUAL How to use this Manual. ................................ 1-1 SAFETY Important Safety Instructions .
HOW TO USE THIS MANUAL CMPS 86290230 02/22/07 This manual contains the f ollowing sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. To reduce the risk of fire, electric shock, or injury: ! WARNING: Connect to a properly grounded outlet .
HAZARD INTENSITY LEVEL CMPS 86290230 02/22/07 2-2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard in tensity identified by signal words - WARNI NG and CAUTION and FOR SAFETY.
GROUNDING INSTRUCTIONS CMPS 86290230 02/22/07 2- 3 THIS PRODUCT IS FOR COMMERCIAL US E ONLY. ELECTRICAL: In the USA, this machine operates on a standard 15 amp 115V, 60 Hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine.
SAFETY LABEL LOCATION CMPS 86290230 02/22/07 NOTE: These drawings indicate the location of safet y labels on the Compass ™ . If, at any time, the labels become illegible contact your Wind so r r epresentative for prompt re placem ent. WARN ING LABEL 86242230 PRV NO .
TECHNICAL SPECIFICATIONS CMPS 86290230 02/22/07 ITEM DIMENSION/CAPACITY Electrical 115V, 12A, 60HZ Electric Pump Motor 1/3hp, 1725rpm Solution Pump 500psi (34 bars), Axial plunger Electric Vacuum Motor 2stage, 1.
HOW THE MACHINE WORKS CMPS 86290230 02/22/07 3-2 The Compass ™ is a multi-functional cleaning machine intended for commercial use. The appliance applies chemical at low pressure and uses high pressure to clean with. Then the soiled water is vacuumed back into the recovery tank.
COMPONENTS CMPS 86290230 02/22/07 3- 3 1. Control Panel 2. Solution Tank 3. Solution Tank Lid 4. Solution Tank Drain Hose 5. Solution Tank Fill Hose 6. Recovery Tank 7. Recovery Tank Lid 8. Recovery Tank Drain Hose 9. Chemical Siphon Caps 10. Electrical Cord 11.
CONTROLS CMPS 86290230 02/22/07 5 1 6 4 2 7 8 3 1. Solution Accessory Tool Hook-Up 2. Vacuum Accessory Tool Hook-Up 3. Pump Switch 4. Vacuum Switch 5. Chemical Selector and Metering Valve 6.
CONTROLS CMPS 86290230 02/22/07 1. SOLUTION ACCESSORY TOOL H OOK-UP Used for various auxiliary-cleaning tools. 2. VACUUM ACCESSORY TOOL HOOK-U P To use accessory tool, remove hose from vac shoe and attach to accessory tool adaptor. 3. PUMP SWITCH Turns the pump On and Off.
OPERATIONS CMPS 86290230 02/22/07 FILLING THE MACHINE Do not put defoamer, solvents spotter or prespray chemicals in the solution tank. 3-6 1. Always use gloves and eye protection. Never spray solution towards people. 2. To fill Use fill hose or po ur directly into solution tank.
OPERATIONS CMPS 86290230 02/22/07 3- 7 7. Use brush or grout tool for heavy soiled area s. 8. Turn Chemical off. Pr essure clean by rinsing surfaces at high pressu re. 9. Use Squeegee or Gulper tool to remove standing water. 10. Store and secure hoses and tools n eatl y.
OPERATIONS CMPS 86290230 02/22/07 3-8 Care must be exercised in the use of all chemicals. Chemicals are poisonous and can pose a health risk. Read and follow manfacturers instructions regarding dangers and correct usages. The internal parts of the pump used in the machine are suitable for use with most carpet cleaning chemicals.
MAINTENANCE CMPS 86290230 02/22/07 4-1 1. Float Shut-Off 2. Strainer 3. Circuit Breakers 4. Vacuum Motor 5. Pump 6. Adjustable Unloader Valve.
MAINTENANCE CMPS 86290230 02/22/07 1. FLOAT SHUT-OFF The float shut-off is located inside th e recovery tank. The purpose of the float shut-off is to notify the user that the recovery tank is full. Remove daily and clean any debris for maximum airflow.
MAINTENANCE CMPS 86290230 02/22/07 4. VACUUM MOTOR Vacuum Motor Carbon Brushes Replacement (Windsor) WARNING: The green ground wire must be attached for safe operation. See wiring diagram. (Refer to vacuum group in the parts sect ion of manual). End Cap 4- 3 ONLY QUALIFIED MAINTENA NCE PE RSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS.
MAINTENANCE CMPS 86290230 02/22/07 5. PUMP 4-4 ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS. SOLUTION PUMP REPLACEMENT 1. Turn off all switches and unplug machine. 2. Tilt machine back so bottom is exposed. 3. Remove the 6 screws that fasten the frame to the solution tank.
MAINTENANCE CMPS 86290230 02/22/07 4-5 PERIODIC MAINTENACE Twice a month, flush a white vinegar sol ution (one quart vinegar to two gallons of water) or anti- browning solution (mixed as directe d) through the machine. This will prevent build-up of alkaline residue in the system.
TROUBLESHOOTING CMPS 86290230 02/22/07 4- 6 PROBLEM CAUSE SOLUTION Dead electrical circuit Check building circuit breaker or fuse box. Faulty power cord Replace Loss of Power GFCI breaker is tripped R.
NOTES: CMPS 86290230 02/22/07 4- 7.
CONTROLS CMPS 86290230 02/22/07 5-1.
CONTROLS CMPS 86290230 02/22/07 5- 2 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86243990 500780 1 LABEL, COVER PANEL 2 86234690 270012 1 COVER, SWITCH PANEL 3 86270990 57090 2 NUT, 10-32 HEX NYLOCK SS 4 86258930 84187 1 VALVE, CHEMICAL METERING 5 86197390 31021 1 ELBOW, 1/4 NPT 45º STREET 6 86279560 87178 3 WASHER, 5/8 ID X 1.
RECOVERY TANK CMPS 86290230 02/22/07 5-3 RECOVERY TANK CMPS 86290230 02/22/07 5-3.
RECOVERY TANK CMPS 86290230 02/22/07 5- 4 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86271830 57283 1 NUT, 3/8 NPT PLASTIC 2 86277040 70781 11 SCR, 5/16-18 X 1/2 HHCS SS NP 3 860106.
SOLUTION TANK CMPS 86290230 02/22/07 5-5.
SOLUTION TANK CMPS 86290230 02/22/07 5- 6 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86290070 - 1 TANK, SOLUTION CMPS 2 86239680 41476 1 HOOK, HOSE STORAGE 3 86276600 70696 10 SCR, .
VACUUM CMPS 86290230 02/22/07 27 10 9 11 16 18 12 13 24 4 23 25 15 26 14 GROUND 22 21 28 14 GROUND (26) 27 WIRE WIRE 20 19 5-7.
VACUUM CMPS 86290230 02/22/07 5- 8 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86237850 35268 2 GASKET, 5.0 OD X 1.75 ID X .38T 2 86092220 270010 1 COVER, VAC MOTOR 3 86238020 36234 1 GASKET, 5.0 OD X 3.1 ID X .75 4 86002390 20063 1 CLAMP, 1.
WHEELS & FRAME CMPS 86290230 02/22/07 5-9.
WHEELS & FRAME CMPS 86290230 02/22/07 5-1 0 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 8620 2280 89252 2 WHEEL, 12” BLK CNTRD HUB 2 8627 1380 57196 2 NUT, 1/2 PUSH-ON DOME CAP.
PUMP CMPS 86290230 04/20/07 6 10 12 4 2 1 3 9 7 8 16 15 13 14 17 18 19 11 13 5 5-11.
PUMP CMPS 86290230 04/20/07 5-1 2 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86223390 67488 1 RECTIFIER, 50A 600V BRIDGE 2 86180220 11-800276 1 ELL, 3/8 BR 3 86290290 - 1 UNLOADER, .
PUMP CMPS 86290230 04/20/07 3 2 1 4 5 6 5-13.
PUMP CMPS 86290230 04/20/07 5-1 4 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86014510 - 1 PUMP ASM, 500 PSI 120V CMPS COMPLETE ASSEMBLY 2 86004370 39547 1 HOSE ASM, 1.5 BLK VAC X 21 3 86002390 20063 1 CLAMP, 1.75 WORM GEAR X .312 4 86264940 27051 2 CABLE TIE, 11.
TOOLS - STANDARD CMPS 86290230 04/20/07 17 3 11 13A 13B 6 4 5 1 2 7 8 9 10 16 5-15.
TOOLS - STANDARD CMPS 86290230 04/20/07 5-1 6 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86257660 02478 1 TOOL, HAND SQUEEGEE 2 86257650 02477 1 TOOL, SCRUB BRUSH HANDLE 3 86257640 .
VAC HOSE RACK – CMPSR ONLY CMPS 86290230 04/20/07 5-17.
VAC HOSE RACK - CMPSR CMPS 86290230 04/20/07 5-1 8 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86240630 49499 1 HOSE RACK 2 86276600 70696 3 SCR, #10 X 3/4 PTHSMS SS 3 86006590 70088.
WIRING – SCHEMATIC CMPS 86290230 04/20/07 PUMP SWITCH PUMP CIRCUIT BREAKER VACUUM SWITCH VACUUM CIRCUIT BREAKER VACUUM MOTOR BLK WHT GRN/YLW VAC MOUNT GROUND PANEL GROUND 88951 BLK BLK WHT PUMP MOTO.
SUGGESTED SPARE PARTS CMPS 86290230 04/20/07 5-2 0 PART NO. PRV NO. DESCRIPTION SERIAL NO. NOTES: 86241930 47419 KIT, SQUEEGEE TOOL BLADES 86256090 730262 STRAINER, 1/2 FPT 80 MESH 86202070 360-04B BR.
TOOLS- DRY CLEAN OPTION CMPS 86290230 04/20/07 5-21.
TOOLS – DRY CLEAN OPTION CMPS 86290230 04/20/07 5-2 2 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86236130 34410 1 FILTER, WET/DRY 2 8625 7630 02474 1 TOOL, WHE E LED BRUSH 3 8625 .
TOOLS- LOW FLOW SPRAY GUN OPTION CMPS 86290230 04/20/07 5 4 3 1 2 6 5-23.
TOOLS – LOW FLOW SPRAY GUN OPTION CMPS 86290230 04/20/07 5-2 4 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86258920 84186 1 VALVE, FLOW ADJUSTMENT 2 86290390 1 GUN, PRESSURE WASH 3.
TOOLS- GROUT CLEANER OPTION CMPS 86290230 04/20/07 5-25.
TOOLS – GROUT CLEANER OPTION CMPS 86290230 04/20/07 5-2 6 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86200820 270-11A 1 NIPPLE, 1/8 FPT QD MALE BRASS 2 86247720 56032 1 NIPPLE, 1/8 CLOSE 3 86194160 11-8 001 33 1 TEE, 1/8 BR 4 86240190 39639 2 HOSE, 1/8 MPT X 1/4 FPT X 12L 5 86090230 87015 4 WASHER, 9/16 ID X 1.
TOOLS- HIGH PRESSURE WAND OPTION CMPS 86290230 04/20/07 5-27.
TOOLS – HIGH PRESSURE WAND OPTION CMPS 86290230 04/20/07 5-2 8 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 8600 5580 56012 1 NIPPLE, 1/4 FPT QD 2 8624 0210 39641 1 HOSE, 1/8 MPT X 1/4 MPT X 7 L 3 8627 4410 70195 1 SCR, 10-32 X 1.
TOOLS- CARPET TOOL OPTION CMPS 86290230 04/20/07 5-29.
TOOLS – CARPET TOOL OPTION CMPS 86290230 04/20/07 5-3 0 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86200820 270-11A 1 NIPPLE, 1/8 FPT QD MALE BRASS 2 86240220 39642 1 HOSE, 1/8 MPT X 1/4 FPT X 12L 3 86197360 31016 1 ELBOW, 1/4 NPT STREET 4 86090230 87015 4 WASHER, 9/16 ID X 1.
STORAGE BAG-OPTION CMPS 86290230 04/20/07 5-31.
STORAGE BAG-OPTION CMPS 86290230 04/20/07 5-3 2 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 8628 3390 47423 1 KIT, STORAGE BAG.
CHEMICAL LOCK-OPTION CMPS 86290230 04/20/07 5-33.
CHEMICAL LOCK-OPTION CMPS 86290230 04/20/07 5-3 4 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86070520 140660 1 BRKT, CHEMICAL LOCK.
NOTES CMPS 86290230 04/20/07 5-35.
An important point after buying a device Windsor CMPSR 10070080 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Windsor CMPSR 10070080 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Windsor CMPSR 10070080 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Windsor CMPSR 10070080 you will learn all the available features of the product, as well as information on its operation. The information that you get Windsor CMPSR 10070080 will certainly help you make a decision on the purchase.
If you already are a holder of Windsor CMPSR 10070080, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Windsor CMPSR 10070080.
However, one of the most important roles played by the user manual is to help in solving problems with Windsor CMPSR 10070080. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Windsor CMPSR 10070080 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
