Instruction/ maintenance manual of the product ADM8 10080170 Windsor
Go to page of 42
Read these instructions bef ore operating the machine MODEL: ADM8 10080170 Operating Instructions 86038230 04/26/11 PRV NO. 98628 AD CARPET EXTRACTOR.
MACHINE DATA LOG/OVERVIEW ADMIRAL 86038230 1 Warranty Registration Thank you for purchasing a Windsor product. Warranty registration is quick and easy. Your registration will allow us to serve y ou better over the lifetime of the product. To register your product go to: www.
TABLE OF CONTENTS ADMIRAL 86038230 2 Machine Data Log/ Overview . ............................... 1 Table of Co ntents ................................................. 2 HOW TO USE THIS MANUAL How to use this Manual. .................................
HOW TO USE THIS MANUAL ADMIRAL 86038230 1-1 This manual contains the f ollowing sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.
SAFETY INSTRUCTIONS ADMIRAL 86038230 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use.
ADMIRAL 86038230 2-2 IMPORTANTES MESURES DE SÉCURITÉ L’utilisation d’un appareil électri que demande certaines précautions: LIRE TOUTES LES INSTRUCTIONS AVANT DE FAI RE FONCTIONNER (CET APPAREIL).
HAZARD INTENSITY LEVEL ADMIRAL 86038230 2-3 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard in tensity identified by signal words - WARNI NG and CAUTION and FOR SAFETY.
DEGRÉS DE RISQUES EN CAS DE DANGER ADMIRAL 86038230 2-4 Les symboles ci-dessous sont utilisés à travers ce manuel comme illustré dans leurs descriptions : DEGRÉS DE RISQUES EN CAS DE DANGER Il existe trois degrés de risques iden tifiés par les termes signalétiques – AVERTISSEMENT et ATTENTION et POUR VOTRE SÉCURITÉ.
GROUNDING INSTRUCTIONS ADMIRAL 86038230 2-5 USING AN ADAPTOR GROUNDING CONNECTION Note: Adaptors are not a llowed in Canada. Outlet Tab for Grounding Outlet Box FIGURE C Grounded FIGURE A Adaptor Screw FIGURE B Adaptor Metal Screw Grounded Grounding Pin THIS PRODUCT IS FOR COMMERCI AL USE ONLY.
TECHNICAL SPECIFICATIONS ADMIRAL 86038230 3-1 POWER TYPE ELECTRICAL: 115 V, 15 A, 60 HZ ELECTRIC VACUUM MOTOR: (1) –3 stage, 1 hp, 99 cfm (2.80 cubic meters/min.) Waterlift –117 ” (297 cm) BRUSH: (1) 15” (38.1 cm.) SOLUTION PUMP: 100 PSI, diaphragm style, internal bypass SOLUTION CAPACITY: 8 gallon s (3 0.
CONTROLS/COMPONENT LOCATIONS ADMIRAL 86038230 3-2 1. Main Handle. Used to pull and maneuver machine. 2. Handle Adjustment. Used to adjust height of handle. 3. Electrical Cord. 4. Solution Switch. Turns on pump. Continuous position (bottom) activates electro-valve to dispense solution to floor through jets.
CONTROLS/COMPONENT LOCATIONS ADMIRAL 86038230 3-3 1. Solution Accessory Tool Hookup. Used for various auxiliary cleaning t ools. 2. Vacuum Hose Door. Used to connect various auxiliary 1 ½ inch cleaning tool vacuum hoses. 3. Brush Height Adjustment. Used to regulate brush height from storage positio n to variou s carpet heights.
CONTROLS/COMPONENT LOCATIONS ADMIRAL 86038230 3-4 1. Solution Intake Cover. 2. Vacuum Intake Cover. 3. Float Shut-Off. 4. Clean-Out Opening. 5. Pour Spout.
FILLING OPERATIONS ADMIRAL 86038230 3-5 FILLING THE ADMIRAL NOTE: Use clean bucket of water to fill solution tank Do not put defoamer, solvents, spotter or prespray chemical s in the solution tank. Do not allow water to spill into vacuum motor inlet. Dry spillage from top of solution tank before replacing recovery tank.
OPERATIONS ADMIRAL 86038230 3-6 Remove electrical co rd and literature from recovery tank. Fill solution tank (see filling instructions page 3-5). Adjust brush to proper setting. Note: For good operation the brush must skim the carpet. If circuit breaker trips raise brush to prevent damage to motor or ca rpet.
OPERATIONS ADMIRAL 86038230 3-7 Select contin uou s setting to st art solution spray or select intermittent setting to enable use of trigger switches to sta rt solution spra y.
CLEANING PROCEDURE ADMIRAL 86038230 3-8 Release intermittent trigger switches or turn off continuous setting on solution switch approximately 1 foot before en ding cleaning pass. Push down on handle to raise vacuum shoe and brush before moving to the next cleaning pass.
CLEANING PROCEDURE ADMIRAL 86038230 3-9 To speed drying, use a Windblo wer ™ fan. Empty recovery tank by releasing dump hose. Use a hose with cold water to clean out the recovery tank. Also drain solution tank after each use. STEP 7 STEP 8 After cleaning, turn off all controls, return brush to storage position and ca refully unplug machine.
ACCESSORY TOOL USAGE ADMIRAL 86038230 3-10 APRV NO. Turn on vacuum motor swit ch and set solution switch to intermittent position. Note: Be sure brush switch is in off position and brush is in storage position. Squeeze handle on accessory tool to begin cleaning.
MAINTENANCE ADMIRAL 86038230 4-1 SERVICE SCHEDULE MAINTENANCE DAILY WEEKLY QUARTERLY Check machine for cord damage * Check recovery dome an d gasket for damage and cleanliness * Check brush – sho uld be clean with no lint or strings attached * Inspect vac shoe for blockage; remove fibers with coat hanger, etc.
MAINTENANCE ADMIRAL 86038230 4-2 PERIODIC MAINTENANCE Twice a month, flush a white vinegar sol ution (One quart vinegar to two gallons of water) or anti- browning solution (mixed as directe d) through the extractor. This will prev ent build-up of alkaline residue in the system.
MAINTENANCE ADMIRAL 86038230 4-3 3 8 [9.5 mm] Carbon Brushes End Cap If armature commutator is gr oo ved, extre mely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center. Important: These brushes wear quicker as the length shortens due to increased heat.
MAINTENANCE ADMIRAL 86038230 4-4 Only qualified maintenance personne l ar e to perform the following repairs. Seul le personnel d'entretien qualif ié peut effectuer des répar ations. 86249420 PRV NO. 62759 86227350 PRV NO. 05016 BELT REPLACEMENT 1.
MAINTENANCE ADMIRAL 86038230 4- 5 Only qualified maintenance personne l ar e to perform the following repairs. Seul le personnel d'entretien qualif ié peut effectuer des répar ations. SOLUTION PUMP REPLACEMENT 1. Turn off all switches and unplug the machi ne.
WIRING DIAGRAM ADMIRAL 86038230 4-6 86268290 PRV NO. 88229 86268460 PRV NO. 88333 86268430 PRV NO. 88323 86238840 PRV NO. 41356 8638830 PRV NO. 41355 86238820 PRV NO .
TROUBLESHOOTING CHART ADMIRAL 86038230 4-7 PROBLEM CAUSE SOLUTION Is the cord plugged in. Plug in cord. Circuit breaker tripped in building. Reset breaker. Faulty switch. Call for service. No Power, Nothing Runs Faulty power cord or pigtail. Call for service.
NOTES: ADMIRAL 86038230 4-8.
FRAME ASSEMBLY ADMIRAL 86038230 5-1 2 16 27 29 20 8 5 22 11 10 15 7 13 14 24 25 4 3 26 34 21 18 19 A 12 33 9 6 B 30 31 32 C 28 (SEE PG. 5-9) (SEE PG. 5-11).
FRAME ASSEMBLY ADMIRAL 86038230 5- 2 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 OPEN - - 2 86003620 34341 1 FRAME, CLP FAMILY 3 86004340 39528 1 HOSE ASM, 1.
BRUSH ASSEMBLY ADMIRAL 86038230 5-3 25 9 3 2 46 5 17 23 36 17 34 45 47 44 25 20 29 30 13 43 33 32 1 14 16 26 15 18 24 30 30 11 25 29 25 7 16 31 10 21 22 40 35 28 42 3 6 19 37 41 27 4 26 12 38 39 8.
BRUSH ASSEMBLY ADMIRAL 86038230 5- 4 REF PART NO. PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86000730 03110 1 AXLE, ROLLER 2 86227100 04084 1 ADAPTER, BRUSH BRG. 3 86000900 09019 2 BEARING, 1.125ODX.500IDX.375 4 86001100 11045 1 BELT, 180J6 MICRO-V 5 86001140 12514 1 BRUSH, 15L X 3.
PUMP ASSEMBLY ADMIRAL 86038230 5-5 3 4 13 10 16 6 5 11 15 19 18 1 20 7 16 8 21 17 9 2 14 12 25 26 23 28 24 26 D 20 (SEE PG. 5-11) 27.
PUMP ASSEMBLY ADMIRAL 86038230 5- 6 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86002470 22072 1 COUPLING, 1/4 ANCHOR W/1" HEX 2 86002480 22090 2 CONNECTOR, 1/8FPT X 1/4 TUBEQC .
VACUUM SHOE ASSEMBLY ADMIRAL 86038230 5-7 4 7 13 3 10 7 5 6 11 8 2 1 12 11.
VACUUM SHOE ASSEMBLY ADMIRAL 86038230 5- 8 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86227350 05016 4 ARM, VAC SHOE PARALLEL 2 86234760 27674 1 COVER, ACCESSORY PORT 3 86005810 57245 4 NUT, 1/4-20 HEX NYLOCK SS 4 86006790 70351 2 SCR, 10-32 X 3/8 HHTR W/STAR 5 86275120 70360 4 SCR, 1/4-20 X.
CONTROL PANEL ASSEMBLY ADMIRAL 86038230 5-9 13 17 6 12 4 10 15 5 14 16 20 7 1 19 18 11 8 3 9 2 36 33 32 31 30 29 28 27 26 25 24 23 22 21 35 34 C (SEE PG.
CONTROL PANEL ASSEMBLY ADMIRAL 86038230 5-1 0 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86001240 14020 1 TERMINAL BLOCK, 115V (3-4-3) 2 86001980 14700 1 BREAKER, 15A 250VAC 50VDC 3.
SOLUTION TANK ASSEMBLY ADMIRAL 86038230 5-11 6 14* 27 16 5* 4 2 8 24* 17* 11 15 20 12B 7 3 13 16 10 1 9 19 18 A B D 7* (SEE PG. 5-1) (SEE PG. 5-5) 22* 21* 23* 18 26 25 28 16 27 29 30 31 32 12A 12 (SEE PG.
SOLUTION TANK ASSEMBLY ADMIRAL 86038230 5-1 2 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86233140 20041 2 CLAMP, 2.0" WORM GEAR 2 86233150 20042 1 CLAMP, 3/8 HOSE (D-SLOT) 3 86.
RECOVERY TANK ASSEMBLY ADMIRAL 86038230 5-13 16 11 7 E 9 2 6 17 13 8 4 15 5 12 E 18 10 1 14 12 3 1B 10B 11B 14B 12.
RECOVERY TANK ASSEMBLY ADMIRAL 86038230 5-1 4 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1A 86002400 20064 1 CLAMP, 2.0" WORM GEAR X .312 1000083447 1B 86002350 20002 1 CLAMP, 2.0” NYLON RATCHET 2 86233140 20041 1 CLAMP, 2.0" WORM GEAR 3 86008400 78499 1 TETJER, DRAIN PLUG 4 86003110 27816 2 COVER, REC.
SUGGESTED SPARE PARTS ADMIRAL 86038230 5-15 PART NO. PRV NO. DESCRIPTION SERIAL NO. FROM NOTES: 86001140 12514 BRUSH, 15L X 3.38OD WAS 12031 86001100 11045 BELT, 180J6 MICRO-V 86000900 09019 BEARING, 1.
An important point after buying a device Windsor ADM8 10080170 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Windsor ADM8 10080170 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Windsor ADM8 10080170 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Windsor ADM8 10080170 you will learn all the available features of the product, as well as information on its operation. The information that you get Windsor ADM8 10080170 will certainly help you make a decision on the purchase.
If you already are a holder of Windsor ADM8 10080170, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Windsor ADM8 10080170.
However, one of the most important roles played by the user manual is to help in solving problems with Windsor ADM8 10080170. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Windsor ADM8 10080170 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
