EN
Western Digital logo
Official user manual

Western Digital 4CH TRIPLEX

87 pages·3.5 MB·DVR·PDF·ENDEFRITNLJA
Western Digital 4CH TRIPLEX
Table of Contents 80 sections USER GUIDE · 4CH TRIPLEX DIGITAL VIDEO RECORDER · SAFETY PRECAUTIONS · EXPLANATION OF SYMBOLS · … ShowHide
USER GUIDEp.14CH TRIPLEX DIGITAL VIDEO RECORDERp.1SAFETY PRECAUTIONSp.2EXPLANATION OF SYMBOLSp.2CAUTIONp.2SEE INSTALLATION INSTRUCTIONS BEFORE CONNECTING TO THE SUPPLYp.2BUILDINGp.2WARNINGp.71. Featuresp.82. Name, Function and Connectionp.92-1. Front Viewp.9A. PLAYBACK BUTTONSp.9B. POWERp.9C. CAPTUREp.9D. RECORDp.9E. REMOVABLE HDD RACKp.9F. NETWORK LEDp.9G. RECORD LEDp.9H. SENSOR LEDp.10I. MOTION LEDp.10J. IR RECEIVERp.10K. SEARCHp.10L. SETUPp.10M. LOCKp.10N. MISCp.10O. AUTOp.10P. QUAD/MUXp.10Q. DIRECTION / “SEL” BUTTONp.10R. ESCp.102-2. Remote Controlp.112-3. Rear Viewp.12A. CAMERA INPUTp.12B. LOOPBACK OUTPUTp.12C. AUDIO INp.12D. AUDIO OUTp.12E. VIDEO OUTp.12F. S-VHSp.12G. RS-232Cp.12H. RS-485p.12I. USB PORTp.12J. NTSC/PAL SWITCHp.12K. ALARM OUTp.12L. POWER FANp.12N. POWER INp.12O. 10 BASE T ETHERNETp.122-4. Specificationp.13VIDEO OUTPUTp.13RECORDp.132-5. Packing Listp.13CONTENTSp.131. DVRp.132. MANUALp.133. POWER CODEp.134. REMOVABLE-HDD RACK KEY & SCREWp.135. REMOTE CONTROLLERp.136. BATTERYp.137. CD - CLIENT SOFTWAREp.133. Factory Defaultp.14„ CHANNEL ROTATIONp.14‹ CHANNELS--------------------------------------------------------------- 1 2 3 4p.14‹ DURATION-----------------------------------------------------------------5 SECONDSp.14„ CHANNEL INFO----------------------------------------------------------------- 1 2 3 4p.14‹ LABEL---------------------------------------------------------------------- CH1p.14„ STATUS DISPLAY-------------------------------------------------------------- SHOWp.14„ ALPHA BLENDING------------------------------------------------------------- 10%p.14„ QUADp.14‹ GENERALp.14QUALITY--------------------------------------------------------HIGH QUALITYp.14SAVE EVENT LOG-------------------------------------------OFFp.14NET FRAME DROP------------------------------------------ONp.14‹ CHANNELp.14FRAME----------------------------------------------------------------AVAILABLE=116p.14RATE-------------------------------------------------------------------1 FRAME/SECp.14RECORDED BYp.14— SENSOR------------------------------------------------------OFFp.14— MOTION-------------------------------------------------------OFFp.14— MANUAL------------------------------------------------------ OFFp.14— CONTINUOUS-----------------------------------------------ONp.14AUDIO------------------------------------------------------------------1 2 3 4p.14‹ SENSORp.14
Page 1 of the Western Digital 4CH TRIPLEX user manual — USER GUIDE
Page 1 · click to enlarge
Page 1

USER GUIDE

4CH TRIPLEX DIGITAL VIDEO RECORDER

Version. 3.0 Design and specifications are subject to change without notice.

Page 2 of the Western Digital 4CH TRIPLEX user manual — BUILDING
Page 2 · click to enlarge
Page 2

SAFETY PRECAUTIONS

Western Digital 4CH TRIPLEX — SAFETY PRECAUTIONS diagram (page 2)
Fig. 1

EXPLANATION OF SYMBOLS

This symbol is intended to alert the user to the presence of important

operation and maintenance (servicing) instructions in the literature

accompanying the appliance.

This symbol is intended to alert the user to the presence of

unprotected “dangerous voltage” within the product’s enclosure that

may be strong enough to cause a risk of electric shock persons.

CAUTION

THIS PRODUCT IS MULTIPLE RATED VOLTAGES (110V AND 220V).

SEE INSTALLATION INSTRUCTIONS BEFORE CONNECTING TO THE SUPPLY

THIS PRODUCT BEARS LITHIUM BATTERY.

RISK OF EXPLOSION IF THE BETTERY ON THE MAIN MOARD IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

THIS EQUIPMENT IS INDOOR USE AND ALL THE COMMUNICATION WIRINGS ARE LIMITED TO INSIDE OF THE

BUILDING

TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

Page 3 of the Western Digital 4CH TRIPLEX user manual — SAFETY PRECAUTIONS
Page 3 · click to enlarge
Page 3
Page 3 of the Western Digital 4CH TRIPLEX user manual — SAFETY PRECAUTIONS
Page 4 of the Western Digital 4CH TRIPLEX user manual — SAFETY PRECAUTIONS
Page 4 · click to enlarge
Page 4
Page 4 of the Western Digital 4CH TRIPLEX user manual — SAFETY PRECAUTIONS
Page 5 of the Western Digital 4CH TRIPLEX user manual — SAFETY PRECAUTIONS
Page 5 · click to enlarge
Page 5
Page 5 of the Western Digital 4CH TRIPLEX user manual — SAFETY PRECAUTIONS
Page 6 of the Western Digital 4CH TRIPLEX user manual — SAFETY PRECAUTIONS
Page 6 · click to enlarge
Page 6
Page 6 of the Western Digital 4CH TRIPLEX user manual — SAFETY PRECAUTIONS
Page 7 of the Western Digital 4CH TRIPLEX user manual — WARNING
Page 7 · click to enlarge
Page 7

WARNING

The authorized expert must install DVR. When connecting a camera, audio, or sensor cables

DVR should be turned off first.

Please be aware that the company is not responsible for the damages caused from using

unauthorized goods and not following the instructions from the manual.

The company is also not responsible for the errors caused after the user has opened up DVR

for an arbitrary fix or the user has removed Warranty seal.

Page 8 of the Western Digital 4CH TRIPLEX user manual — 1. Features
Page 8 · click to enlarge
Page 8

1. Features

z 4 channels real-time video display and 4 channels real-time video recording

z TRIPLEX – Simultaneous record, playback and network transfer

z Individual channel recording and playback with different frame rate

z High-quality live and playback resolution

z High-quality images with MPEG-2 video compression

z Network featuresRemote searching or playback, remote live-monitoring, remote

settings change, remote camera control, and remote upgrade

z Network via LAN (DHCP), ADSL (Dynamic and Static IP address)

z 4 channels audio recording

z Various recording triggersMotion detection, manual recording button, sensor, and

z Search menu geared with graphic user interface, which provides fast, simple, and

z User-friendly setup menu with graphic user interface

z Easy to schedule a complicated weekly recording plan

z Convenient search menu that displays recording status

z The OSD icons on screen provide various helpful and well-explained information

z Up-to-date motion-detection that offers 4 area-setup for each channel

z USB ports for JPEG data backup and software upgrade using USB flash memory stick

z Still image capture and review as JPEG format

z Internal Pan/Tilt/Zoom/Focus controller

z Easy operating with the buttons on the front and the remote controller

z User verification by password certification

z Video loss detection

z CD-RW (Option)Backup, S/W upgrade

schedule · detailed information · z Web-viewer

Page 9 of the Western Digital 4CH TRIPLEX user manual — G. RECORD LED
Page 9 · click to enlarge
Page 9

2. Name, Function and Connection

2-1. Front View

Western Digital 4CH TRIPLEX — 2. Name, Function and Connection diagram (page 9)
Fig. 2 · 2. Name, Function and Connection
Western Digital 4CH TRIPLEX — 2. Name, Function and Connection diagram (page 9)
Fig. 3 · 2. Name, Function and Connection

A. PLAYBACK BUTTONS

REW, REW JUMP/STEP, PLAY/PAUSE, JUMP/STEP, and FF buttons are used for

playing recorded videos.

B. POWER

Press this button to power on/off DVR. A red light appears when the power of DVR is

turned on.

C. CAPTURE

Press this button to save a captured still-image during playback as a JPEG file.

D. RECORD

Press this button to start/stop manual recording. A red light appears during the

recording.

E. REMOVABLE HDD RACK

Removable HDD rack to install default hard disk drive

F. NETWORK LED

A red light appears when the network client is connected to DVR.

G. RECORD LED

A red light appears during DVR is recording.

Page 10 of the Western Digital 4CH TRIPLEX user manual — R. ESC
Page 10 · click to enlarge
Page 10

H. SENSOR LED

A red light appears when sensor perceives event.

I. MOTION LED

A red light appears when DVR detects motion.

J. IR RECEIVER

Remote Controller signal receiver

K. SEARCH

Press this button to begin searching the recorded video.

L. SETUP

Press this button to begin changing DVR setup.

M. LOCK

Press this button to lock/unlock the buttons of DVR.

N. MISC

Press this button once to show or hide the status icons on live screen and playback

Press twice to move to “1.Brightness 2.Contrast 3.Alphablending 4.OSD Position”

adjustment menu of each channel,

Press triple to move to “1.Pan/Tilt 2.Zoom/Focus 3.Camera Initial” control menu of

each channel.

O. AUTO

Press this button to activates/deactivates channel rotating function during full screen

display of single channel.

P. QUAD/MUX

To switch the display from 1-channel video to 4-channels video in live display, and vice

versa.

Q. DIRECTION / “SEL” BUTTON

These can be used as arrow keys and number key.

buttons are used as 1,

2, 3, and 4, respectively.

buttonUsed to change possible values in Setup menu
buttonUsed to move items in Setup menu

“SEL” button in the middle is used for various purposes.

“SEL” button: Used to enter each sub menu. Also used to select number values.

R. ESC

Press this button to go back to the previous menu

screen,

Page 11 of the Western Digital 4CH TRIPLEX user manual — 2-2. Remote Control
Page 11 · click to enlarge
Page 11

2-2. Remote Control

Western Digital 4CH TRIPLEX — 2-2. Remote Control diagram (page 11)
Fig. 4 · 2-2. Remote Control
Page 12 of the Western Digital 4CH TRIPLEX user manual — N. POWER IN
Page 12 · click to enlarge
Page 12

2-3. Rear View

Western Digital 4CH TRIPLEX — 2-3. Rear View diagram (page 12)
Fig. 5 · 2-3. Rear View

A. CAMERA INPUT

BNC Input Connectors for camera

B. LOOPBACK OUTPUT

BNC Loop-back Output Connectors for cameras

C. AUDIO IN

RCA Audio Input Terminals

D. AUDIO OUT

RCA Audio Output Terminal

E. VIDEO OUT

BNC Monitor Out Connector

F. S-VHS

S-VHS Monitor Out Connector

G. RS-232C

Connector for DVR Control and Upgrade

H. RS-485

I. USB PORT

J. NTSC/PAL SWITCH

K. ALARM OUT

L. POWER FAN

M. SENSOR IN (Power input: DC 10~12V)

N. POWER IN

O. 10 BASE T ETHERNET

Connector for Network Connection

Camera Control

Page 13 of the Western Digital 4CH TRIPLEX user manual — Table of Contents
Page 13 · Contents
Contents

Contents

USER GUIDEp.14CH TRIPLEX DIGITAL VIDEO RECORDERp.1SAFETY PRECAUTIONSp.2EXPLANATION OF SYMBOLSp.2CAUTIONp.2SEE INSTALLATION INSTRUCTIONS BEFORE CONNECTING TO THE SUPPLYp.2BUILDINGp.2WARNINGp.71. Featuresp.82. Name, Function and Connectionp.92-1. Front Viewp.9A. PLAYBACK BUTTONSp.9B. POWERp.9C. CAPTUREp.9D. RECORDp.9E. REMOVABLE HDD RACKp.9F. NETWORK LEDp.9G. RECORD LEDp.9H. SENSOR LEDp.10I. MOTION LEDp.10J. IR RECEIVERp.10K. SEARCHp.10L. SETUPp.10M. LOCKp.10N. MISCp.10O. AUTOp.10P. QUAD/MUXp.10Q. DIRECTION / “SEL” BUTTONp.10R. ESCp.102-2. Remote Controlp.112-3. Rear Viewp.12A. CAMERA INPUTp.12B. LOOPBACK OUTPUTp.12C. AUDIO INp.12D. AUDIO OUTp.12E. VIDEO OUTp.12F. S-VHSp.12G. RS-232Cp.12H. RS-485p.12I. USB PORTp.12J. NTSC/PAL SWITCHp.12K. ALARM OUTp.12L. POWER FANp.12N. POWER INp.12O. 10 BASE T ETHERNETp.122-4. Specificationp.13VIDEO OUTPUTp.13RECORDp.132-5. Packing Listp.13CONTENTSp.131. DVRp.132. MANUALp.133. POWER CODEp.134. REMOVABLE-HDD RACK KEY & SCREWp.135. REMOTE CONTROLLERp.136. BATTERYp.137. CD - CLIENT SOFTWAREp.133. Factory Defaultp.14„ CHANNEL ROTATIONp.14‹ CHANNELS--------------------------------------------------------------- 1 2 3 4p.14‹ DURATION-----------------------------------------------------------------5 SECONDSp.14„ CHANNEL INFO----------------------------------------------------------------- 1 2 3 4p.14‹ LABEL---------------------------------------------------------------------- CH1p.14„ STATUS DISPLAY-------------------------------------------------------------- SHOWp.14„ ALPHA BLENDING------------------------------------------------------------- 10%p.14„ QUADp.14‹ GENERALp.14QUALITY--------------------------------------------------------HIGH QUALITYp.14SAVE EVENT LOG-------------------------------------------OFFp.14NET FRAME DROP------------------------------------------ONp.14‹ CHANNELp.14FRAME----------------------------------------------------------------AVAILABLE=116p.14RATE-------------------------------------------------------------------1 FRAME/SECp.14RECORDED BYp.14— SENSOR------------------------------------------------------OFFp.14— MOTION-------------------------------------------------------OFFp.14— MANUAL------------------------------------------------------ OFFp.14— CONTINUOUS-----------------------------------------------ONp.14AUDIO------------------------------------------------------------------1 2 3 4p.14‹ SENSORp.14
Page 14 of the Western Digital 4CH TRIPLEX user manual — „ CHANNEL ROTATION
Page 14 · click to enlarge
Page 14

3. Factory Default

„ CHANNEL ROTATION

‹ CHANNELS--------------------------------------------------------------- 1 2 3 4

‹ DURATION-----------------------------------------------------------------5 SECONDS

„ CHANNEL INFO----------------------------------------------------------------- 1 2 3 4

‹ LABEL---------------------------------------------------------------------- CH1

„ STATUS DISPLAY-------------------------------------------------------------- SHOW

„ ALPHA BLENDING------------------------------------------------------------- 10%

„ QUAD

‹ GENERAL

QUALITY--------------------------------------------------------HIGH QUALITY

SAVE EVENT LOG-------------------------------------------OFF

NET FRAME DROP------------------------------------------ON

‹ CHANNEL

FRAME----------------------------------------------------------------AVAILABLE=116

RATE-------------------------------------------------------------------1 FRAME/SEC

RECORDED BY

— SENSOR------------------------------------------------------OFF

— MOTION-------------------------------------------------------OFF

— MANUAL------------------------------------------------------ OFF

— CONTINUOUS-----------------------------------------------ON

AUDIO------------------------------------------------------------------1 2 3 4

‹ SENSOR

SENSOR NUMBER------------------------------------------------ 1

— TYPE----------------------------------------------------------- NORMAL OPEN

— RELAY OUTPUT

¾ ALARM------------------------------------------- 1 2

¾ CHANNEL------------------------------------- ON

¾ DURATION------------------------------------ 5 SECONDS

‹ MOTION

REGION--------------------------------------------------------------- FULL

RELAY OUTPUT

— ALARM NUMBER------------------------------------------ 1 2

z LIVE · z RECORD

Page 15 of the Western Digital 4CH TRIPLEX user manual — POST RECORD--------------------------------------------------- 2 SECONDS
Page 15 · click to enlarge
Page 15

SENSITIVITY L 1 2 3 4 5 6 7 8 9 H

POST RECORD 2 SECONDS

„ MUX

‹ GENERAL

RESOLUTION -------------------------------------------------------360 X 240

QUALITY-------------------------------------------------------------- HIGH QUALITY

SAVE EVENT LOG--------------------------------------------------OFF

NET FRAME DROP------------------------------------------------ON

‹ CHANNEL

CHANNEL NUMBER ---------------------------------------------CH1

— FRAME RATE ---------------------------------------------- AVAILABLE=116

— RATE-----------------------------------------------------------1 FRAME/SEC

— RECORDED BY

¾ SENSOR---------------------------------------- OFF

¾ MOTION----------------------------------------- OFF

¾ MANUAL--------------------------------------- OFF

¾ CONTINUOUS--------------------------------ON

— AUDIO--------------------------------------------------------- 1 2 3 4

‹ SENSOR

SENSOR NUMBER----------------------------------------------- 1

— TYPE---------------------------------------------------------- NORMAL OPEN

— RELAY OUTPUT

¾ ALARM----------------------------------------- 1 2

¾ CHANNEL------------------------------------- 1 2 3 4

¾ DURATION------------------------------------ 5 SECONDS

‹ MOTION

CHANNEL NUMBER ---------------------------------------------CH1

— REGION------------------------------------------------------ FULL

— RELAY OUTPUT

¾ ALARM NUMBER--------------------------------- 1 2

— SENSITIVITY L 1 2 3 4 5 6 7 8 9 H

POST RECORD 2 SECONDS

„ SCHEDULE

„ ADMIN PASSWORD--------------------------------------------------------- SELECT

„ USER PASSWORD----------------------------------------------------------- SELECT

z SYSTEM

Page 16 of the Western Digital 4CH TRIPLEX user manual — „ STORAGE OVERWRITE-------------------------------------------------- ON
Page 16 · click to enlarge
Page 16

„ FACTORY DEFAULT SELECT

„ DATE FORMAT--------------------------------------------------------------YYYY/MM/DD

„ CURRENT DATE------------------------------------------------------------YYYY/MM/DD

„ CURRENT TIME------------------------------------------------------------- HH:MM:SS

„ GMT AREA-------------------------------------------------------------------- [GMT+0:00]

„ DAYLIGHT SAVING--------------------------------------------------------- OFF

„ SITE ID------------------------------------------------------------------------- DVR

„ LOG----------------------------------------------------------------------------- SELECT

„ SYSTEM -----------------------------------------------------------------------SELECT

„ CAPTURED IMAGE-------------------------------------------------------- SELECT

„ SEND MAIL -------------------------------------------------------------------OFF

„ PTZ CHANNELS ------------------------------------------------------------ 1 2 3 4

‹ CAMERA TYPE ------------------------------------------------------ - - -

‹ CAMERA ID------------------------------------------------------------ 1

„ CLIENT ACCESS -------------------------------------------------------------ON

„ PORT NUMBER -------------------------------------------------------------- 4456

„ NETWORK TYPE-------------------------------------------------------------LAN

‹ DHCP-------------------------------------------------------------------OFF

‹ DDNS--------------------------------------------------------------------ON

‹ DDNS SERVER IP xxx.xxx.xxx.xxx

‹ IP ADDRESS xxx.xxx.xxx.xxx

‹ GATEWAY xxx.xxx.xxx.xxx

‹ SUBNET MASK xxx.xxx.xxx.xxx

„ STORAGE OVERWRITE ON

„ HDD FORMAT---------------------------------------------------------------- MASTER

„ AUTO ERASING (30DAYS) ---------------------------------------------- OFF

„ CD-RW BACKUP SELECT (CD-RW version only)

„ S/W UPGRADE W/ CD-RW SELECT (CD-RW version only)

Show 4 more labels / short text on this page
z INFO · z PTZ · z NETWORK · z STORAGE
Page 17 of the Western Digital 4CH TRIPLEX user manual — 4-2-1. Channel Rotation
Page 17 · click to enlarge
Page 17

4. Setup

4-1. Initial menu

Press the Setup button, then Setup menu will appear.

Western Digital 4CH TRIPLEX — 4. Setup diagram (page 17)
Fig. 6 · 4. Setup
Western Digital 4CH TRIPLEX — 4. Setup diagram (page 17)
Fig. 7 · 4. Setup

4-2. LIVE

4-2-1. Channel Rotation

1. Select LIVE and press SEL button to show LIVE setup screen.
2. Select a live display rotation channel among channel 1,2,3,4 with SEL button. (Yellow

means that the channel is included in channel rotation during live display. The only

yellow colored channels will be appeared in channel rotation during live display. White

means that the channel is not included in channel rotation during live display.)

Western Digital 4CH TRIPLEX — 4-2-1. Channel Rotation diagram (page 17)
Fig. 8 · 4-2-1. Channel Rotation
3. Select a channel for channel rotation, move the cursor to “Duration” to set the rotation

time of display screen. (Duration time varies 2, 3, 5, 10, 15, 20, & 30 seconds) 4-2-2. Channel Info 4-2-2-1. LABEL

1. Select LIVE and press SEL button to show LIVE setup menu
2. Go to CHANNEL INFO and select the channel you wish to change the channel name of.

The name of the chosen channel shows up at LABEL field.

Page 18 of the Western Digital 4CH TRIPLEX user manual — 4-2-2-3. ALPHABLENDING
Page 18 · click to enlarge
Page 18
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 18)
Fig. 9 · 3. Factory Default
3. Press SEL button when the cursor is LABEL field (channel name). A keyboard will

appear for you to type in a new name.

Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 18)
Fig. 10 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 18)
Fig. 11 · 3. Factory Default
4. Name the label (channel name) by using

buttons and SEL button. Press

enter to save. The name is changed in LABEL field.

4-2-2-2. Status Display

1. Select LIVE and press SEL button to show LIVE setup menu
2. Select whether to or the status Information by using

buttons.

Western Digital 4CH TRIPLEX — 4-2-2-2. Status Display diagram (page 18)
Fig. 12 · 4-2-2-2. Status Display

shows the status information on the live screen (channel name, HDD Status,

Current Time, LOCK, NETWORK)

hides the status information on the live screen. When is checked, press the

MISC button to show the status information.

4-2-2-3. ALPHABLENDING

1. Select LIVE and press SEL button to show LIVE setup menu.
2. Adjust Alpha Blending from 0% to 90% by using

buttons.

Page 19 of the Western Digital 4CH TRIPLEX user manual — 4-3. RECORD
Page 19 · click to enlarge
Page 19
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 19)
Fig. 13 · 3. Factory Default

4-3. RECORD

In Record Setup, you can choose from QUAD, MUX, and SCHEDULE recording mode. In each mode, the

recording quality, recording frame, audio, sensor, motion detector, and other details can be customized. 4-3-1. Select Recording Mode (QUAD, MUX, SCHEDULE)

1. Select RECORD and press SEL button to go to the recording mode select screen.
Western Digital 4CH TRIPLEX — 4-3. RECORD diagram (page 19)
Fig. 14
2. Move the cursor to SELECT MODE bar and press SEL button.
Western Digital 4CH TRIPLEX — 4-3. RECORD diagram (page 19)
Fig. 15

The current recording mode is highlighted in colors.

3. Use

buttons to move the cursor to the desired mode (QUAD, MUX or

SCHEDULE) and press SEL button.

Page 20 of the Western Digital 4CH TRIPLEX user manual — 3. Factory Default
Page 20 · click to enlarge
Page 20
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 20)
Fig. 16 · 3. Factory Default
4. The selected mode becomes highlighted. Press ESC button to go back to LIVE mode,

and from then the selected recording mode will be applied to recording sessions. 4-3-2. QUAD Recording Mode

Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 20)
Fig. 17 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 20)
Fig. 18 · 3. Factory Default

1. Select RECORD and press SEL button to go to Select Mode for recording.
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 20)
Fig. 19 · 3. Factory Default
2. Select QUAD on the Select Mode screen to go to QUAD setup screen.
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 20)
Fig. 20 · 3. Factory Default
Page 21 of the Western Digital 4CH TRIPLEX user manual — 4-3-2-2. CHANNEL Setup
Page 21 · click to enlarge
Page 21

4-3-2-1. GENERAL Setup

In QUAD Setup screen, select GENERAL to go to the GENERAL setup screen.

Western Digital 4CH TRIPLEX — 4-3-2-1. GENERAL Setup diagram (page 21)
Fig. 21 · 4-3-2-1. GENERAL Setup

z QUALITY – Press

button to select recording quality.

DVR supports three types of recording quality in QUAD recording mode.

offers somewhat harsh picture quality and small file size.

offers average picture quality and medium file size.

offers fine picture quality but file size is the largest.

The user should choose the appropriate quality level considering his/her purpose.

z SAVE EVEN LOG – Press

button to set ON or OFF

- LOG will be recorded when events occur.

z NET FRAME DROP - Press

button to set ON or OFF

- When network bandwidth is not sufficient for transmitting all frames, DVR

transmits only I frame, dropping B and P frame.

4-3-2-2. CHANNEL Setup

Select CHANNEL in QUAD setup screen to go to CHANNEL setup screen.

Western Digital 4CH TRIPLEX — 4-3-2-2. CHANNEL Setup diagram (page 21)
Fig. 22 · 4-3-2-2. CHANNEL Setup

z FRAME RATE – It shows the available frame rate.

button to select the recording speed.

The QUAD recording mode supports

NTSC1, 4, 8, 15, 22, and 30FPS
PAL1, 4, 7, 13, 18 and 25FPS

z RATE –Press

Page 22 of the Western Digital 4CH TRIPLEX user manual — 4-3-2-3. SENSOR Setup
Page 22 · click to enlarge
Page 22

z SENSOR – Press

button to set or .

: Video will be recorded when the sensor is activated.

Please refer to “4-3-2-3. SENSOR Setup”.

z MOTION – Press

button to set or .

: Video will be recorded when the motion is detected.

Please refer to “4-3-2-4. MOTION Setup”.

z MANUAL - Press

button to set or

: Video will be recorded when the user press RECORD button.

z CONTINUOUS - Press

button to set or

: Video will be ALWAYS recorded when DVR is in operation.

z AUDIO – Move the cursor on the one of , , , and and press SEL

button to select the audio port that will be recorded. The selected audio channels

will be highlighted in Yellow.

4-3-2-3. SENSOR Setup

In QUAD setup screen, select SENSOR to go to SENSOR setup screen.

Western Digital 4CH TRIPLEX — 4-3-2-3. SENSOR Setup diagram (page 22)
Fig. 23 · 4-3-2-3. SENSOR Setup

5 seconds of Pre-Record will be applied to all channels as default.

z SENSOR NUMBER – Press

button to select sensor that one want to set and

link with the recording channel.

z TYPE - Press

button to select the type of sensor to be activated.

Select the right sensor type according to the type of installed sensor with DVR.

NORMAL OPEN – Normal Open type sensor

NORMAL CLOSE – Normal Close type sensor

z ALARM - Press

button to select the port on which an alarm out is made

Page 23 of the Western Digital 4CH TRIPLEX user manual — 4-3-2-4. MOTION DETECTION Setup
Page 23 · click to enlarge
Page 23

when sensor is activated.

z CHANNEL - Press

button to set or

: Video will be recorded when the sensor is activated.

z DURATION - Press

button to select the duration of alarm output and the

recording time of the linked channel.

Available alarm output and channel recording duration – 5, 10, 15, 30, 60, 120, and 180

seconds.

4-3-2-4. MOTION DETECTION Setup

In QUAD setup screen, select MOTION to go to MOTION setup screen.

Western Digital 4CH TRIPLEX — 4-3-2-4. MOTION DETECTION Setup diagram (page 23)
Fig. 24 · 4-3-2-4. MOTION DETECTION Setup

z REGION – FULL

In QUAD mode, the motion detection is applied to full screen region only.

z ALARM NUMBER - Press

buttons to select the port on which an alarm out is

made when motion is detected.

z SENSITIVITY – Move the cursor on the field of SENSIVITY “L 1 2 3 4 5 6 7 8 9 H”

and select sensitivity using

buttons. The selected sensitivity will be highlighted

in Yellow color.

SENSITIVITY “1” - Only reacts to big movements (low sensitivity).

SENSITIVITY “5” - Reacts to average movements (medium sensitivity).

SENSITIVITY “9” - Reacts even to small movements (high sensitivity).

z POST RECORD – Using

buttons, select the duration of post-recording.

Page 24 of the Western Digital 4CH TRIPLEX user manual — 4-3-3-1. GENERAL Setup
Page 24 · click to enlarge
Page 24

4-3-3. MUX Recording Mode

Western Digital 4CH TRIPLEX — 4-3-3. MUX Recording Mode diagram (page 24)
Fig. 25 · 4-3-3. MUX Recording Mode
Western Digital 4CH TRIPLEX — 4-3-3. MUX Recording Mode diagram (page 24)
Fig. 26 · 4-3-3. MUX Recording Mode

<RESOLUTION: 360X240> <RESOLUTION: 720X480>

Difference in recording resolution depending on image resolution setting in MUX mode

1. Select RECORD and press SEL to move to RECORD select mode.
Western Digital 4CH TRIPLEX — <RESOLUTION: 360X240> <RESOLUTION: 720X480> diagram (page 24)
Fig. 27
2. Select MUX in RECORD select mode screen to go to MUX setup screen.
Western Digital 4CH TRIPLEX — <RESOLUTION: 360X240> <RESOLUTION: 720X480> diagram (page 24)
Fig. 28

4-3-3-1. GENERAL Setup

In MUX setup screen, select GENERAL to move to GENERAL select mode.

Page 25 of the Western Digital 4CH TRIPLEX user manual — 4-3-3-2. CHANNEL Setup
Page 25 · click to enlarge
Page 25
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 25)
Fig. 29 · 3. Factory Default

z RESOLUTION – Press

button to select recording resolution.

z QUALITY – Press

button to select recording quality.

DVR supports four types of picture quality in MUX recording mode.

offers somewhat harsh picture quality but small file size.

offers average picture quality and average file size.

offers fine picture quality and big file size.

User should choose the appropriate picture quality considering his/her purpose.

z SAVE EVEN LOG – Press

button to set ON or OFF

- LOG will be recorded when events occur.

z NET FRAME DROP - Press

button to set ON or OFF

- When network bandwidth is not sufficient for transmitting all frames, DVR

transmits only I frame, dropping B and P frame.

4-3-3-2. CHANNEL Setup

In MUX setup screen, select CHANNEL to go to CHANNEL setup screen.

Western Digital 4CH TRIPLEX — 4-3-3-2. CHANNEL Setup diagram (page 25)
Fig. 30 · 4-3-3-2. CHANNEL Setup

z CHANNEL NUMBER - Press

button to select the channel.

z FRAME RATE – It shows the available frame rate.

button to select the recording speed of the channel.

The MUX recording mode supports

NTSC: 360x240 - 1 to 30FPS / 720X480 - 1, 4, 8, 15, 22, and 30FPS

PAL: 360X288 - 1 to 25FPS / 720X576 - 1, 4, 7, 13, 18 and 25FPS

z RATE –Press

Page 26 of the Western Digital 4CH TRIPLEX user manual — 4-3-3-3. SENSOR Setup
Page 26 · click to enlarge
Page 26

z SENSOR – Press

button to set or .

: Video will be recorded when the sensor is activated.

Please refer to “4-3-3-3. SENSOR Setup”.

z MOTION – Press

button to set or .

: Video will be recorded when the motion is detected.

Please refer to “4-3-3-4. MOTION Setup”.

z MANUAL - Press

button to set or

: Video will be recorded when the user press RECORD button.

z CONTINUOUS - Press

button to set or

: Video will be ALWAYS recorded when DVR is in operation.

z AUDIO – Move the cursor on the one of , , , and audio inputs and

press SEL button to select the audio port that will be recorded. The selected audio

channels will be highlighted in Yellow.

4-3-3-3. SENSOR Setup

In MUX screen, select SENSOR to go to SENSOR setup screen.

Western Digital 4CH TRIPLEX — 4-3-3-3. SENSOR Setup diagram (page 26)
Fig. 31 · 4-3-3-3. SENSOR Setup

5 seconds of Pre-Record will be applied to all channels as default.

z SENSOR NUMBER – Press

button to select sensor that one want to set and

link with recording channel.

z TYPE - Press

button to select the type of sensor to be activated

Select the right sensor type according to the type of installed sensor with DVR.

NORMAL OPEN – Normal Open type sensor

NORMAL CLOSE – Normal Close type sensor

z ALARM - Press

button to select the port on which an alarm out is made

Page 27 of the Western Digital 4CH TRIPLEX user manual — 4-3-3-4. MOTION DETECTION Setup
Page 27 · click to enlarge
Page 27

when sensor is activated.

z CHANNEL - Press

button to select the channel to record when sensor is

activated.

z DURATION - Press

button to select the duration of alarm output and the

recording time of the linked channel.

Available alarm output and channel recording duration – 5, 10, 15, 30, 60, 120, and 180

4-3-3-4. MOTION DETECTION Setup

In MUX setup screen, select MOTION to go to MOTION setup screen.

Western Digital 4CH TRIPLEX — 4-3-3-4. MOTION DETECTION Setup diagram (page 27)
Fig. 32 · 4-3-3-4. MOTION DETECTION Setup

z CHANNEL NUMBER - Press

buttons to select the channel to set the motion

detection.

z REGION – Press

buttons to select the process of the motion detection area

setup.

: The motion detection is always applied to full screen region.

: The user can set 4 motion detection areas per channel. Please refer to “5-11.

Motion Detection Region Setup” for individual motion detection area setup.

z ALARM NUMBER - Press

buttons to select the port on which an alarm out is

made when motion is detected.

z SENSITIVITY – Move the cursor on the field of SENSIVITY “L 1 2 3 4 5 6 7 8 9 H”

and select sensitivity using

buttons. The selected sensitivity will be highlighted

in Yellow color.

SENSITIVITY “1” - Only reacts to big movements (low sensitivity).

SENSITIVITY “5” - Reacts to average movements (medium sensitivity).

SENSITIVITY “9” - Reacts even to small movements (high sensitivity).

z POST RECORD – Using

buttons, select the duration of post-recording.

seconds

Page 28 of the Western Digital 4CH TRIPLEX user manual — 4-3-4-1. Applied Function with Respect to the Cursor’s Location
Page 28 · click to enlarge
Page 28

4-3-4. SCHEDULE Recording Mode

SCHEDULE supports the weekly recording plan. The default recording mode of schedule is

MUX recording mode and recording frame rate set in MUX recording mode is applied. (Please

refer to “4-3-3-2. CHANNEL setup”)

1. Select RECORD and press SEL to move to RECORD select mode.
Western Digital 4CH TRIPLEX — 4-3-4. SCHEDULE Recording Mode diagram (page 28)
Fig. 33 · 4-3-4. SCHEDULE Recording Mode
2. Select SCHEDULE to go to the screen where recording schedule can be set. The

screen will show the plan chart of one day of the week.

Western Digital 4CH TRIPLEX — 4-3-4. SCHEDULE Recording Mode diagram (page 28)
Fig. 34 · 4-3-4. SCHEDULE Recording Mode

4-3-4-1. Applied Function with Respect to the Cursor’s Location

z TIMEApplies to the whole region
z CH1Applies only to the CH1 column
z CH2Applies only to the CH2 column
z CH3Applies only to the CH3 column
z CH4Applies only to the CH4 column
z 1~23Applies only to the specified time slot
z PREVMove to the previous day of the week
z NEXTMove to the next day of the week
z COPY PREVCopy schedule of current day to the previous day of the week and

move to that day.

z COPY NEXT: Copy schedule of current day to the next day of the week and move to

that day.

Page 29 of the Western Digital 4CH TRIPLEX user manual — 4-3-4-3. Schedule setup as QUAD recording mode
Page 29 · click to enlarge
Page 29

4-3-4-2. Mapping Recording methods and Front Buttons Front Buttons Recording Method Detailed Feature REW SENSOR Record when the sensor is activated BACK JUMP/STEP MOTION Record when motion is detected PLAY/PAUSE RECORD Record continuously JUMP/STEP MOTION & SENSOR Record by sensor and motion detection FF NONE No recording CAPTURE QUAD Record in QUAD mode

Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 29)
Fig. 35 · 3. Factory Default

When the recording setups in QUAD and MUX mode differ from what is used in schedule, DVR

records by using the method that would record more.

(E.g. If MUX channel 1 is set to record by MOTION and it is to be recorded by SENSOR in

SCHEDULE, channel 1 will be recorded by both SENSOR and MOTION.)

4-3-4-3. Schedule setup as QUAD recording mode

To set QUAD recording mode, place the cursor on TIME and 0 to 23 and press

CAPTURE button then QUAD passage will appear on each cell.

When Schedule is set as QUAD recording mode, recording frame rate and settings in

QUAD setup will be applied. (Please refer to “4-3-2-2. CHANNEL setup”)

Western Digital 4CH TRIPLEX — 4-3-4-3. Schedule setup as QUAD recording mode diagram (page 29)
Fig. 36 · 4-3-4-3. Schedule setup as QUAD recording mode
Page 30 of the Western Digital 4CH TRIPLEX user manual — 4-4. SYSTEM
Page 30 · click to enlarge
Page 30

4-4. SYSTEM

Select SYSTEM and press SEL button to go to SYSTEM setup menu. 4-4-1. ADMIN PASSWORD

ADMIN PASSWORD can be edited here.

Western Digital 4CH TRIPLEX — 4-4. SYSTEM diagram (page 30)
Fig. 37
Western Digital 4CH TRIPLEX — 4-4. SYSTEM diagram (page 30)
Fig. 38
1. Place the cursor on “Select” in the field of ADMIN PASSWORD and press SEL button.
2. CURRENT PASSWORD: Enter the current password using 1,2,3, and 4 and press SEL

button.

3. NEW PASSWORD: Enter a new password using 1,2,3, and 4 and press SEL button.
4. CONFIRM PASSWORD: Retype the new password and press SEL button to confirm the

new password. When “Password Changed” appears as bellow, press “YES” using SEL

button to confirm the change.

Western Digital 4CH TRIPLEX — 4-4. SYSTEM diagram (page 30)
Fig. 39
Western Digital 4CH TRIPLEX — 4-4. SYSTEM diagram (page 30)
Fig. 40
Western Digital 4CH TRIPLEX — 4-4. SYSTEM diagram (page 30)
Fig. 41
Western Digital 4CH TRIPLEX — 4-4. SYSTEM diagram (page 30)
Fig. 42

The factory default password is “1111”.

To delete password, just press SEL button without typing any numbers in the NEW

PASSWORD and CONFIRM PASSWORD field.

Applied region and authorization of ADMIN PASSWORD & USER PASSWORD

z ADMIN – All setting changes and other features are accessible

z USER – Making setup changes and turning off the power is disallowed

The user can make Password (ADMIN PASSWORD & USER PASSWORD) ONLY using the

numbers of “1”, “2”, “3”, and “4”. The available figures of the password (ADMIN PASSWORD

& USER PASSWORD) are 8 figures.

Page 31 of the Western Digital 4CH TRIPLEX user manual — 4-4-4. DATE FORMAT
Page 31 · click to enlarge
Page 31

4-4-2. USER PASSWORD

USER PASSWORD can be edited here.

Western Digital 4CH TRIPLEX — 4-4-2. USER PASSWORD diagram (page 31)
Fig. 43
1. Place the cursor on the “Select” and press SEL button.
2. CURRENT PASSWORD: Enter the current password and press SEL button.
3. NEW PASSWORD: Enter a new password and press SEL button.
4. RETYPE PASSWORD: Retype the new password and press SEL button.

The default password is “1111.”

To delete password, just press SELECT without typing any numbers in the NEW PASSWORD

and CONFIRM PASSWORD field.

4-4-3. FACTORY DEFAULT

Reset DVR to factory default settings.

Western Digital 4CH TRIPLEX — 4-4-3. FACTORY DEFAULT diagram (page 31)
Fig. 44
Western Digital 4CH TRIPLEX — 4-4-3. FACTORY DEFAULT diagram (page 31)
Fig. 45
Western Digital 4CH TRIPLEX — 4-4-3. FACTORY DEFAULT diagram (page 31)
Fig. 46
Western Digital 4CH TRIPLEX — 4-4-3. FACTORY DEFAULT diagram (page 31)
Fig. 47
Western Digital 4CH TRIPLEX — 4-4-3. FACTORY DEFAULT diagram (page 31)
Fig. 48
1. When the system is reset with factory default settings, all customized settings shall be

removed.

2. Users can maintain the user defined and customized settings very easily with network client

S/W, please refer to “7-6-5. Saving and loading settings.”

4-4-4. DATE FORMAT

It display format of the date and the user can changed the format of date.

Page 32 of the Western Digital 4CH TRIPLEX user manual — 4-4-5. CURRENT DATE
Page 32 · click to enlarge
Page 32
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 32)
Fig. 49 · 3. Factory Default

Supported date formats and examples

z YYYY-MM-DD Î 2003-07-11

z MM-DD-YYYY Î 07-11-2003

z DD-MM-YYYY Î 11-07-2003

z YYYY/MM/DD Î 2003/07/11

4-4-5. CURRENT DATE

It displays current date, which can be edited.

Western Digital 4CH TRIPLEX — 4-4-5. CURRENT DATE diagram (page 32)
Fig. 50
1. Place the cursor on the Current Date field and press SEL button. This will highlight

the first part of the date (one of year, month, or day depending on the display format)

in yellow.

2. Press

buttons to set the date in the shown date format.

3. Press SEL button to apply the changed date.
4. If there are existing data on the date of editing, DVR display “If yes, the recorded

data will be deleted.” as shown below.

Western Digital 4CH TRIPLEX — 4-4-5. CURRENT DATE diagram (page 32)
Fig. 51
Western Digital 4CH TRIPLEX — 4-4-5. CURRENT DATE diagram (page 32)
Fig. 52
Page 33 of the Western Digital 4CH TRIPLEX user manual — NOTICE
Page 33 · click to enlarge
Page 33
5. Press “YES” to delete the related data or press “NO” to keep the data and cancel the

date change.

WARNING

If the user selects , all the data from the changed date will be deleted.

4-4-6. CURRENT TIME

Displays the current time, which can be edited.

Western Digital 4CH TRIPLEX — 4-4-6. CURRENT TIME diagram (page 33)
Fig. 53
1. Place the cursor on the Current Time field and press SEL button. This will highlight

the front part of the displayed time yellow.

2. Use

buttons to set the time in hr/min/sec format.

3. Press SEL button to apply the changed time.
4. If there are existing data at the time of editing, DVR display “If yes, the recorded data

will be deleted.”

5. Press “YES” to delete the related data or press “NO” to keep the data and cancel the

time change.

4-4-7. GMT AREA

buttons to add or lessen to adjust the time of DVR in accordance with GMT time

zone of the country or territory. Then the time in the field of CURRENT TIME will be changed.

Western Digital 4CH TRIPLEX — 4-4-7. GMT AREA diagram (page 33)
Fig. 54
Western Digital 4CH TRIPLEX — 4-4-7. GMT AREA diagram (page 33)
Fig. 55

NOTICE

To apply DAYLIGHT SAVING function properly, GMT AREA setting should be done before

DAYLIGHT SAVING setting. Please refer to WORLD TIME ZONE MAP.

Press

Page 34 of the Western Digital 4CH TRIPLEX user manual — EXCEPTION
Page 34 · click to enlarge
Page 34

4-4-8. DYALIGHT SAVING

1. Press

buttons to decide whether to apply DAYLIGHT SAVING or not by selecting

or .

Western Digital 4CH TRIPLEX — 4-4-8. DYALIGHT SAVING diagram (page 34)
Fig. 56
2. After selecting , move the cursor to BEGIN (MM/DD/HH) field and press SEL

button. This will highlight the front part of the displayed date in yellow.

3. Use

buttons to set the date in MM/DD/HH format.

4. Press SEL button to apply the changed time.
Western Digital 4CH TRIPLEX — 4-4-8. DYALIGHT SAVING diagram (page 34)
Fig. 57
5. When CURRENT DATE and CURRENT TIME is located between BEGIN and END,

DLS (DAYLIGHT SAVING) is applied and operated.

Western Digital 4CH TRIPLEX — 4-4-8. DYALIGHT SAVING diagram (page 34)
Fig. 58
Western Digital 4CH TRIPLEX — 4-4-8. DYALIGHT SAVING diagram (page 34)
Fig. 59

NOTICE

- The Northern Hemisphere: The date and time in BEGIN is earlier than END.

- The Southern Hemisphere: The date and time in END is earlier than BEGIN.

EXCEPTION

- DLS can’t start from 23:00.

- DLS can’t be applied, if the date of BEGIN and END is same.

Page 35 of the Western Digital 4CH TRIPLEX user manual — 3. Factory Default
Page 35 · click to enlarge
Page 35
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 35)
Fig. 60 · 3. Factory Default
Page 36 of the Western Digital 4CH TRIPLEX user manual — 4-5-2. LOG
Page 36 · click to enlarge
Page 36

4-5. INFO

Select INFO from the SETUP menu and press SEL button to go to INFO setup screen. 4-5-1. SITE ID

Site description of DVR is shown and can be edited here.

Western Digital 4CH TRIPLEX — 4-5. INFO diagram (page 36)
Fig. 61
Western Digital 4CH TRIPLEX — 4-5. INFO diagram (page 36)
Fig. 62
Western Digital 4CH TRIPLEX — 4-5. INFO diagram (page 36)
Fig. 63
Western Digital 4CH TRIPLEX — 4-5. INFO diagram (page 36)
Fig. 64

Enter in the site description by using

buttons and SEL button and press the

ENTER key on the keyboard to save and apply the new description.

4-5-2. LOG

LOG files are shown here.

Western Digital 4CH TRIPLEX — 4-5-2. LOG diagram (page 36)
Fig. 65

Place the cursor “Select” LOG field and press SEL button. The window will appear as

bellow.

Western Digital 4CH TRIPLEX — 4-5-2. LOG diagram (page 36)
Fig. 66
Western Digital 4CH TRIPLEX — 4-5-2. LOG diagram (page 36)
Fig. 67
Western Digital 4CH TRIPLEX — 4-5-2. LOG diagram (page 36)
Fig. 68
Western Digital 4CH TRIPLEX — 4-5-2. LOG diagram (page 36)
Fig. 69
1. Select date using

button and SEL button on the left window. Then the cursor

will be shifted to the right window.

Page 37 of the Western Digital 4CH TRIPLEX user manual — 4-5-4. CAPTURED IMAGE
Page 37 · click to enlarge
Page 37
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 37)
Fig. 70 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 37)
Fig. 71 · 3. Factory Default
2. Press

buttons and SEL button to open the LOG list.

Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 37)
Fig. 72 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 37)
Fig. 73 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 37)
Fig. 74 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 37)
Fig. 75 · 3. Factory Default

4-5-3. SYSTEM

Displays DVR information such as name of tools.

Western Digital 4CH TRIPLEX — 4-5-3. SYSTEM diagram (page 37)
Fig. 76
Western Digital 4CH TRIPLEX — 4-5-3. SYSTEM diagram (page 37)
Fig. 77
Western Digital 4CH TRIPLEX — 4-5-3. SYSTEM diagram (page 37)
Fig. 78
Western Digital 4CH TRIPLEX — 4-5-3. SYSTEM diagram (page 37)
Fig. 79
Western Digital 4CH TRIPLEX — 4-5-3. SYSTEM diagram (page 37)
Fig. 80
Western Digital 4CH TRIPLEX — 4-5-3. SYSTEM diagram (page 37)
Fig. 81

¾ SYSTEM NAME – It shows the model name of DVR.

¾ SERIAL ID – It shows the serial ID of DVR.

¾ SOFTWARE VERSION – It shows the software version of DVR.

¾ HARDWARE VERSION – It shows the hardware version of DVR.

¾ CURRENT IP ADDRESS – It shows, if available, the assigned IP address that is in

use by DVR.

¾ HDD CAPACITY – It shows the HDD capacity of DVR.

4-5-4. CAPTURED IMAGE

The images that were captured during playback can be displayed here.

Page 38 of the Western Digital 4CH TRIPLEX user manual — 4-5-5. SEND MAIL (IP ADDRESS Mailing)
Page 38 · click to enlarge
Page 38
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 38)
Fig. 82 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 38)
Fig. 83 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 38)
Fig. 84 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 38)
Fig. 85 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 38)
Fig. 86 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 38)
Fig. 87 · 3. Factory Default

Captured images are sorted by date/time, which indicates the time of recording. Select a

file from the list to view the captured image.

To capture a still image and view, please refer to “5-8. Still Image Capturing, Viewing, and

Viewing.”

4-5-5. SEND MAIL (IP ADDRESS Mailing)

If the network is linked with LAN-DHCP or ADSL, which support dynamic IP addresses, DVR

can send out the dynamic allocated IP addresses by mails. It is unnecessary for a distant user

to confirm the IP address when he/she connects to the network since he/she can view it after

receiving it by email.

1. Press

buttons to decide whether to send mail or not by selecting or

.

Western Digital 4CH TRIPLEX — 4-5-5. SEND MAIL (IP ADDRESS Mailing) diagram (page 38)
Fig. 88 · 4-5-5. SEND MAIL (IP ADDRESS Mailing)
Western Digital 4CH TRIPLEX — 4-5-5. SEND MAIL (IP ADDRESS Mailing) diagram (page 38)
Fig. 89 · 4-5-5. SEND MAIL (IP ADDRESS Mailing)

Move the cursor to MAIL ADRESS field and press SEL button to type in the mail address on

the keyboard that appears.

Western Digital 4CH TRIPLEX — 4-5-5. SEND MAIL (IP ADDRESS Mailing) diagram (page 38)
Fig. 90 · 4-5-5. SEND MAIL (IP ADDRESS Mailing)
Western Digital 4CH TRIPLEX — 4-5-5. SEND MAIL (IP ADDRESS Mailing) diagram (page 38)
Fig. 91 · 4-5-5. SEND MAIL (IP ADDRESS Mailing)
Western Digital 4CH TRIPLEX — 4-5-5. SEND MAIL (IP ADDRESS Mailing) diagram (page 38)
Fig. 92 · 4-5-5. SEND MAIL (IP ADDRESS Mailing)
Western Digital 4CH TRIPLEX — 4-5-5. SEND MAIL (IP ADDRESS Mailing) diagram (page 38)
Fig. 93 · 4-5-5. SEND MAIL (IP ADDRESS Mailing)
Western Digital 4CH TRIPLEX — 4-5-5. SEND MAIL (IP ADDRESS Mailing) diagram (page 38)
Fig. 94 · 4-5-5. SEND MAIL (IP ADDRESS Mailing)

To type @, press “Caps Lock” button. Then @ will appear on the top line.

Page 39 of the Western Digital 4CH TRIPLEX user manual — 4-5-6. BUZZER
Page 39 · click to enlarge
Page 39
2. Press

buttons and SEL button to type an email address on the keyboard,

and use “ENTER” button on the keyboard to save and apply the changed e-mail

address.

Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 39)
Fig. 95 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 39)
Fig. 96 · 3. Factory Default
3. Move the cursor under Mail Server IP field and press SEL button to select the IP

number. Then the first part should turn into yellow color as bellow.

Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 39)
Fig. 97 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 39)
Fig. 98 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 39)
Fig. 99 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 39)
Fig. 100 · 3. Factory Default

buttons to modify the IP address. The other parts of the IP address can be

modified as same as the first part.

4. Press SEL button to apply the modified IP Address.

IMPORTANT

To receive e-mail with Dynamic IP address from DVR, User has to apply IP address of Mail Server

run by Manufacturer on the field of “MAIL SERVER IP”.

4-5-6. BUZZER

User can turn ON or OFF the sound of inter buzzer.

Western Digital 4CH TRIPLEX — 4-5-6. BUZZER diagram (page 39)
Fig. 101
Western Digital 4CH TRIPLEX — 4-5-6. BUZZER diagram (page 39)
Fig. 102
Western Digital 4CH TRIPLEX — 4-5-6. BUZZER diagram (page 39)
Fig. 103
Western Digital 4CH TRIPLEX — 4-5-6. BUZZER diagram (page 39)
Fig. 104

Press

Page 40 of the Western Digital 4CH TRIPLEX user manual — screen. 4-7-1. CLIENT ACCESS
Page 40 · click to enlarge
Page 40

4-6. PTZ

In order to use the PTZF function, the same camera type as the PTZF camera that is connected

to the chosen channel should be selected as follows.

1. Select DEVICE and press SEL button to show DEVICE setup menu.
2. On the field of , select the channel on which you wish to change the

PTZF type of the camera. The field of will show the camera type that is

currently selected for that channel.

Western Digital 4CH TRIPLEX — 4-6. PTZ diagram (page 40)
Fig. 105
3. After selecting the channel, move the cursor to the field of using

buttons. Select the camera type, using

buttons.

4. If the camera has a specific camera ID, move the cursor on the field of

and select the camera ID using

buttons.

4-7. NETWORK

Select NETWORK from the SETUP menu and press SEL button to go to NETWORK setup

screen. 4-7-1. CLIENT ACCESS

The access from NETWORK CLIENT S/W can be turned off.

Western Digital 4CH TRIPLEX — screen. 4-7-1. CLIENT ACCESS diagram (page 40)
Fig. 106 · screen. 4-7-1. CLIENT ACCESS
Western Digital 4CH TRIPLEX — screen. 4-7-1. CLIENT ACCESS diagram (page 40)
Fig. 107 · screen. 4-7-1. CLIENT ACCESS
Western Digital 4CH TRIPLEX — screen. 4-7-1. CLIENT ACCESS diagram (page 40)
Fig. 108 · screen. 4-7-1. CLIENT ACCESS
Western Digital 4CH TRIPLEX — screen. 4-7-1. CLIENT ACCESS diagram (page 40)
Fig. 109 · screen. 4-7-1. CLIENT ACCESS
Western Digital 4CH TRIPLEX — screen. 4-7-1. CLIENT ACCESS diagram (page 40)
Fig. 110 · screen. 4-7-1. CLIENT ACCESS
Western Digital 4CH TRIPLEX — screen. 4-7-1. CLIENT ACCESS diagram (page 40)
Fig. 111 · screen. 4-7-1. CLIENT ACCESS
Western Digital 4CH TRIPLEX — screen. 4-7-1. CLIENT ACCESS diagram (page 40)
Fig. 112 · screen. 4-7-1. CLIENT ACCESS
Western Digital 4CH TRIPLEX — screen. 4-7-1. CLIENT ACCESS diagram (page 40)
Fig. 113 · screen. 4-7-1. CLIENT ACCESS

- The access between NETWORK CLIENT S/W and the system will be blocked up.

Page 41 of the Western Digital 4CH TRIPLEX user manual — NOTE
Page 41 · click to enlarge
Page 41

4-7-2. LAN

Users connected to LAN network, which uses static IP addresses, should follow the setup

described below.

1. Press

buttons to set network type to .

2. Press

buttons to set DHCP to .

3. Press

buttons to set DDNS to .

4. Use

buttons to edit DDNS SERVER IP Address. And press SEL button to

apply the changed DDNS SERVER IP address.

Western Digital 4CH TRIPLEX — 4-7-2. LAN diagram (page 41)
Fig. 114
Western Digital 4CH TRIPLEX — 4-7-2. LAN diagram (page 41)
Fig. 115
Western Digital 4CH TRIPLEX — 4-7-2. LAN diagram (page 41)
Fig. 116

NOTE

To use DDNS function, the DVR Serial number and Domain Name should be registered at

DDNS Server.

5. Place the cursor on the IP Address field and press SEL button. This will highlight the

first part of IP address in yellow color.

Western Digital 4CH TRIPLEX — NOTE diagram (page 41)
Fig. 117
Western Digital 4CH TRIPLEX — NOTE diagram (page 41)
Fig. 118
Western Digital 4CH TRIPLEX — NOTE diagram (page 41)
Fig. 119
Western Digital 4CH TRIPLEX — NOTE diagram (page 41)
Fig. 120
6. Use

buttons to edit the IP Address. And press SEL button to apply the

changed IP address.

7. Edit GATAWAY and SUBNET MASK using the same method as above. 4-7-3. LAN –DHCP (Dynamic Host Configuration Protocol)

Users connected to LAN – DHCP network, which uses dynamic IP addresses, should follow the

setup described below.

Page 42 of the Western Digital 4CH TRIPLEX user manual — 4-7-4. ADSL
Page 42 · click to enlarge
Page 42
1. Press

buttons to set network type to .

2. Press

buttons to set DHCP to .

3. Press

buttons to set DDNS to .

4. Use

buttons to edit DDNS SERVER IP Address. And press SEL button to

apply the changed DDNS SERVER IP address.

NOTE

To use DDNS function, the DVR Serial number and Domain Name should be registered at

DDNS Server.

5. When DVR is rebooted, the newly assigned IP address appears in the CURRENT IP

ADDRESS field.

Western Digital 4CH TRIPLEX — NOTE diagram (page 42)
Fig. 121
Western Digital 4CH TRIPLEX — NOTE diagram (page 42)
Fig. 122
Western Digital 4CH TRIPLEX — NOTE diagram (page 42)
Fig. 123
Western Digital 4CH TRIPLEX — NOTE diagram (page 42)
Fig. 124
Western Digital 4CH TRIPLEX — NOTE diagram (page 42)
Fig. 125
Western Digital 4CH TRIPLEX — NOTE diagram (page 42)
Fig. 126

For setting a mail address that will receive the assigned IP addresses that are frequently

changed, please refer to “4-5-5. SEND MAIL (IP ADDRESS Mailing).”

4-7-4. ADSL

Users connected to ADSL network, which uses dynamic IP addresses, should follow the setup

description below.

1. Press

buttons to set network type to .

Western Digital 4CH TRIPLEX — 4-7-4. ADSL diagram (page 42)
Fig. 127
Western Digital 4CH TRIPLEX — 4-7-4. ADSL diagram (page 42)
Fig. 128
Western Digital 4CH TRIPLEX — 4-7-4. ADSL diagram (page 42)
Fig. 129
Western Digital 4CH TRIPLEX — 4-7-4. ADSL diagram (page 42)
Fig. 130
Western Digital 4CH TRIPLEX — 4-7-4. ADSL diagram (page 42)
Fig. 131
2. Place the cursor on “default” in the SERVICE ID field and press SEL button to type the

ADSL service ID. Then the keyboard will appear.

Page 43 of the Western Digital 4CH TRIPLEX user manual — 4-8-2. HDD FORMAT
Page 43 · click to enlarge
Page 43
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 43)
Fig. 132 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 43)
Fig. 133 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 43)
Fig. 134 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 43)
Fig. 135 · 3. Factory Default
3. Press

buttons and SEL button to type the ADSL service ID on the keyboard,

and use “ENTER” button on the keyboard to save and apply the saved ID.

4. Edit PASSWORD using the same method as editing SERVICE ID.
8. Press

buttons to set DDNS to .

5. Use

buttons to edit DDNS SERVER IP Address. And press SEL button to

apply the changed DDNS SERVER IP address.

6. The assigned IP address appears in the CURENT IP ADDRESS field.

For setting a mail address that will receive the assigned IP addresses that are frequently

changed, please refer to “4-5-5. SEND MAIL (IP ADDRESS Mailing).”

4-8. STORAGE

Select STORAGE and press SEL button to go to STORAGE setup screen.

Western Digital 4CH TRIPLEX — 4-8. STORAGE diagram (page 43)
Fig. 136

4-8-1. STORAGE OVERWRITE

Set up storage overwriting of the hard disk.

: The oldest data will be deleted and replaced with new data if the hard disk has

fully been recorded.

4-8-2. HDD FORMAT

You can format the hard disk by deleting all stored data.

1. Place the cursor on “SELECT” and press SEL button. DVR will show “ All data will

be deleted from HDD.” to confirm the procedure.

Page 44 of the Western Digital 4CH TRIPLEX user manual — 4-8-5. S/W UPGRADE W/ CD-RW (Available only in model with CD-RW)
Page 44 · click to enlarge
Page 44
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 44)
Fig. 137 · 3. Factory Default
2. If you select “YES,” DVR will reconfirm the formatting procedure, showing “ Do you

really want to delete all data?”

Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 44)
Fig. 138 · 3. Factory Default
3. Formatting will proceed when you select “YES”. If you select “NO”, the hard disk

formatting will not proceed and all saved data will be maintained.

WARNING

Formatting the hard disk by deleting all saved data will delete the captured images

as well. If you wish to preserve the captured images, please save those images by

network client S/W before proceeding of HDD formatting.

4-8-3. AUTO ERASING (30DAYS)

: The data prior 30days from the temporary date will be automatically deleted.

4-8-4. CD-RW BACKUP (Available only in model with CD-RW)

This menu is to be enabled only when DVR has CD-RW.

Please refer to “5-15. Video back up in CD”.

4-8-5. S/W UPGRADE W/ CD-RW (Available only in model with CD-RW)

This menu is to be enabled only when DVR has CD-RW. The upgrade guide will be provided by

another material.

Page 45 of the Western Digital 4CH TRIPLEX user manual — 5-2-1. QUAD Screen Setup
Page 45 · click to enlarge
Page 45

5. OPERATIONS

5-1. Power ON/OFF

5-1-1. Power ON

A. Connect the camera input cables to the camera input port on the back of DVR.

B. Connect the monitor cable to the video output port on the back of DVR.

C. Connect the power cable to the power input port on the back of DVR.

D. Press the POWER button only after DVR and other equipments have been fully

connected. The LED on the POWER button and SENSOR, MOTION, RECORD, and

NETWORK LED on the front right view will light up when DVR starts up.

Western Digital 4CH TRIPLEX — 5-1-1. Power ON diagram (page 45)
Fig. 139 · 5-1-1. Power ON

E. The graphic image (with logo or without logo) will appear while DVR is being booted.

F. After the logo disappears, a divided screen shows up on the monitor.

G. The LOCK function is automatically activated when DVR is initially started up. To use

the ‘LIVE screen viewing’ and other functions, press the LOCK button and enter in the

password. (The factory default password is ‘1111’.)

H. The LED on the POWER button stays lit up while DVR is being operated. 5-1-2. Power OFF

A. DVR cannot be turned off using the POWER button when the LOCK function is on.

Deactivate the LOCK function by pressing LOCK and entering the password.

B. Turn off DVR by pressing the POWER button on the front view of DVR.

C. When DVR is being turned off, the LED on the POWER button and SENSOR,

MOTION, RECORD, and NETWORK LED on the front right view stay on for a while.

D. The LED is no longer lit when DVR is turned off.

5-2. LIVE Display

5-2-1. QUAD Screen Setup

You can switch from Quarterly Divided Screen Setup from Full Screen mode and vice versa

by pressing QUAD/MUX button.

Page 46 of the Western Digital 4CH TRIPLEX user manual — 5-3-1. OSD ICON on LIVE Screen
Page 46 · click to enlarge
Page 46
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 46)
Fig. 140 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 46)
Fig. 141 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 46)
Fig. 142 · 3. Factory Default

5-2-2. Individual Full Screen Setup

Press the channel buttons on DVR to select a channel. The selected channel is highlighted

as yellow. Press SEL button to display the channel in full screen.

Western Digital 4CH TRIPLEX — 5-2-2. Individual Full Screen Setup diagram (page 46)
Fig. 143 · 5-2-2. Individual Full Screen Setup
Western Digital 4CH TRIPLEX — 5-2-2. Individual Full Screen Setup diagram (page 46)
Fig. 144 · 5-2-2. Individual Full Screen Setup
Western Digital 4CH TRIPLEX — 5-2-2. Individual Full Screen Setup diagram (page 46)
Fig. 145 · 5-2-2. Individual Full Screen Setup
Western Digital 4CH TRIPLEX — 5-2-2. Individual Full Screen Setup diagram (page 46)
Fig. 146 · 5-2-2. Individual Full Screen Setup

5-2-3. Auto Channel Rotation

This function is useful when viewing each of the channels in full screen one by one. To set

time interval and channels to rotate, please refer to “4-2 LIVE Setup/ A. Channel Rotation”

5-3. OSD ICON

5-3-1. OSD ICON on LIVE Screen

OSD Icon shows the operation status of DVR on the LIVE screen.

Page 47 of the Western Digital 4CH TRIPLEX user manual — 5-4. LED Information
Page 47 · click to enlarge
Page 47
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 47)
Fig. 147 · 3. Factory Default

(2) It shows the recording trigger.

‹ R – When recording is triggered by Manual record button.

‹ M – When recording is triggered by Motion detection.

‹ S – When recording is triggered by Sensor.

(3) Remaining space in Hard Disk

(6) LOCK, AUTO, NETWORK Status

– When NETWORK CLIENT is connected.

- DVR is locked by a password.

– Auto Channel Rotation is turned on

5-3-2. Show/Hide OSD ICON on LIVE Screen

You can hide OSD Icon by pressing MISC button. Press MISC button again and press ESC

button to show OSD Icon.

Western Digital 4CH TRIPLEX — 5-3-2. Show/Hide OSD ICON on LIVE Screen diagram (page 47)
Fig. 148 · 5-3-2. Show/Hide OSD ICON on LIVE Screen

Please refer to “4-2. LIVE Setup / B. STATUS INFO”.

5-4. LED Information

A. MOTION – LED lights up when motion is detected.

B. SENSOR – LED lights up when sensor is activated.

C. RECORD – LED lights up when recording is in progress

D. NETWORK – LED lights up when Network client is connected.

Show 6 more labels / short text on this page
(1) Channel Name · (4) Date · (5) Time · ‹ · ‹ · ‹
Page 48 of the Western Digital 4CH TRIPLEX user manual — 5-6-1. Search when DVR has one HDD
Page 48 · click to enlarge
Page 48

5-5. Recording

5-5-1. MANUAL Recording

In Manual Recording, manually press the buttons on DVR to record. This method is

useful when recording is necessary while monitoring live channels. The recordable

channels are limited to the channels that its Record By Manual function is turned on.

This is explained under “4-3-2-2. CHANNEL Setup (QUAD) / 4-3-3-2. CHANNEL Setup

(MUX)”. When the RECORD button is pressed, the LED on the RECORD button, the

RECORD LED, and “R” icon on the screen lights up and starts recording. Press the

RECORD button again to stop recording.

5-5-2. SCHEDULE Recording

In Scheduled Recording, DVR automatically records at the specified time. Please refer

to “4-3-3. SCHEDULE Record Mode” for Scheduled Recording Setup.

5-5-3. SENSOR Recording

When SENSOR is operated, SENSOR LED, RECORD LED and “S” on the screen light

up and the channel that is connected to the Sensor starts to record. Please refer to “4-

3-2-3. SENSOR Setup (QUAD)” / “4-3-3-3. SENSOR Setup (MUX)”. 5-5-4. MOTION Recording

When motion is detected, MOIITON LED lights up, RECORD LED and “M” on the screen

light up and the channel that is connected to the motion is recorded. Please refer to “4-3-

2-4. MOTION Setup (QUAD)” / “4-3-3-4 MOTION Setup (MUX)”)

5-5-5. CONTINOUS Recording

DVR is always recording, when DVR is running. Please refer to “4-3-2-2. CHANNEL

Setup (QUAD)” / “4-3-3-2. CHANNEL Setup (MUX)”.

5-6. PLAYBACK

5-6-1. Search when DVR has one HDD

A. Press the SEARCH button to go to the Search Menu.

B. Select the date firstly with

buttons. Press SEL button to move to select channel.

Page 49 of the Western Digital 4CH TRIPLEX user manual — 3. Factory Default
Page 49 · click to enlarge
Page 49

The selected date is highlighted yellow.

Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 49)
Fig. 149 · 3. Factory Default

C. Select a desired channel with

buttons. Selected channel is highlighted yellow.

Press SEL button to set the time. Refer to Audio Recording and SENSOR & MOTION

related recording information.

Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 49)
Fig. 150 · 3. Factory Default

D. Move the TIME BAR (Red Vertical Bar) to select time at the bottom of the Recording

Information Columns. Move the time bar using

buttons. The time bar moves by

7, 15, 22, 30, 37, 45, 52, 00 minutes. The selected time is shown up on the upper part

of the Select Channel field.

Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 49)
Fig. 151 · 3. Factory Default

E. To change the date again, move to Date by pressing SEL button.

F. After completing time selection, move to the playback screen by pressing the

PLAY/PAUSE button.

z QUAD – 4 channels are displayed at once

z MUX (Resolution360 X 240) – The selected channel is displayed. The channel is

played in full screen mode. Press SEL button to playback with the original recording

resolution during playback.

z MUX (Resolution: 720 X 480) – The selected channel is displayed.

Page 50 of the Western Digital 4CH TRIPLEX user manual — D. REW
Page 50 · click to enlarge
Page 50

During playback, press the MISC button to hide the OSD ICON (date, channel name, time,

playing speed, time bar). 5-6-2. Search when DVR has two HDD

A. At first you need to set removable HDD as SLAVE and fixed HDD as master. The

installation guide will be provided by another material.

B. Press the SEARCH button to go to the Search Menu. Then the window for HDD

selection will be appeared.

Western Digital 4CH TRIPLEX — playing speed, time bar). 5-6-2. Search when DVR has two HDD diagram (page 50)
Fig. 152 · playing speed, time bar). 5-6-2. Search when DVR has…

C. Select HDD that you want to search and playback. And then the next steps are the

same as “5-6-1. Search when DVR has one HDD”. 5-6-3. Playback buttons

Western Digital 4CH TRIPLEX — same as “5-6-1. Search when DVR has one HDD”. 5-6-3. Playback buttons diagram (page 50)
Fig. 153 · same as “5-6-1. Search when DVR has one HDD”. 5-6-3.…

A. PLAY/PAUSE

Press the button to play channels in normal speed (X1).

Press it again to pause.

B. FF

Press the button to play channels faster than the normal speed (X1)

The fast-forwarding speed is shown up on the upper right corner of the display screen.

i. X2 – twice as fast

ii. X4 – 4 times as fast

iii. X16 – 16 times as fast

C. JUMP/STEP

When playback is paused, press the button to step forward to the next frame.

During play or fast-forward, it jumps 2 minutes forward from the current spot.

D. REW

Press the button to reverse play channel faster than the normal speed ( - X1).

The speed is shown up on the upper right corner of the display screen.

i. - X2 – twice as fast

ii. - X4 – 4 times as fast

Page 51 of the Western Digital 4CH TRIPLEX user manual — 5-7-2. Viewing Captured Image
Page 51 · click to enlarge
Page 51

iii. - X16 – 16 times as fast

E. JUMP/STEP

When playback is paused, press the button to step backward to the previous frame.

During play or fast-forward, it jumps 2 minutes backward from the current spot.

5-7. Still Image Capturing, Viewing, and Backup

5-7-1. Capturing Still Image

During playback, press the Pause PLAY/PAUSE button to pause playing screen at desired

spot and press the CAPTURE button. It saves 3 consecutive frames as one file.

Western Digital 4CH TRIPLEX — 5-7-1. Capturing Still Image diagram (page 51)
Fig. 154 · 5-7-1. Capturing Still Image
Western Digital 4CH TRIPLEX — 5-7-1. Capturing Still Image diagram (page 51)
Fig. 155 · 5-7-1. Capturing Still Image

You must press the Play/Pause button to pause the screen, then press the Capture button in

order to capture images.

5-7-2. Viewing Captured Image

Select a list to play the images. Saved frames can be viewed in order by pressing SEL

button. The image that is saved in 360X240 is played in 360X240 in the middle of the

monitor screen. The image that is saved in 720X480 is played in 720X480 in full of the

monitor screen.

Western Digital 4CH TRIPLEX — 5-7-2. Viewing Captured Image diagram (page 51)
Fig. 156 · 5-7-2. Viewing Captured Image
Western Digital 4CH TRIPLEX — 5-7-2. Viewing Captured Image diagram (page 51)
Fig. 157 · 5-7-2. Viewing Captured Image
Western Digital 4CH TRIPLEX — 5-7-2. Viewing Captured Image diagram (page 51)
Fig. 158 · 5-7-2. Viewing Captured Image
Western Digital 4CH TRIPLEX — 5-7-2. Viewing Captured Image diagram (page 51)
Fig. 159 · 5-7-2. Viewing Captured Image
Western Digital 4CH TRIPLEX — 5-7-2. Viewing Captured Image diagram (page 51)
Fig. 160 · 5-7-2. Viewing Captured Image
Page 52 of the Western Digital 4CH TRIPLEX user manual — 5-8-1. PTZF Operation
Page 52 · click to enlarge
Page 52
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 52)
Fig. 161 · 3. Factory Default

5-7-3. Still image Backup in USB flash memory stick

1. Connect an USB flash memory stick into USB port.
2. Select the still image that you want to backup in an USB flash memory stick. Please

refer to “5-8-2. Viewing Captured Image”.

3. Press SEL button. Then the still image will be stored in an USB flash memory stick.

NOTICE

Please contact to the supplier or installer of DVR in order to confirm the compatible models of

USB flash memory stick.

5-8. PTZF

5-8-1. PTZF Operation

To control the PTZF functions of the camera, connect the controller to the RS-485 port.

For speed dome cameras that supports RS-485, connect them directly to the RS-485 port. But if

the camera is controlled with RS-232C, one needs to use Signal Converter (RS-485 to RS-232C).

1. In PTZ from the SETUP menu, set the protocol type of the camera for the channel you

wish to control to be the same as the camera that is installed. If the camera has a specific

camera ID, move the cursor on the field of and select the camera ID using

buttons.

2. Press the MISC button in triple to go to the screen where PTZF can be adjusted.
Page 53 of the Western Digital 4CH TRIPLEX user manual — 3. Factory Default
Page 53 · click to enlarge
Page 53
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 53)
Fig. 162 · 3. Factory Default
3. PAN/TILT – to pan or tilt the selected channel
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 53)
Fig. 163 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 53)
Fig. 164 · 3. Factory Default
4. ZOOM/FOCUS – to zoom or focus the selected channel
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 53)
Fig. 165 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 53)
Fig. 166 · 3. Factory Default
5. CAMERA INITIAL – to go to CAMERA INITIAL settings for the selected channel
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 53)
Fig. 167 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 53)
Fig. 168 · 3. Factory Default

This menu is to initialize the PTZ setting of the camera.

Although the camera is initialized, no message will be appeared.

Page 54 of the Western Digital 4CH TRIPLEX user manual — 5-8-2. PTZF Camera link to RS-485
Page 54 · click to enlarge
Page 54

5-8-2. PTZF Camera link to RS-485

Western Digital 4CH TRIPLEX — 5-8-2. PTZF Camera link to RS-485 diagram (page 54)
Fig. 169 · 5-8-2. PTZF Camera link to RS-485
Page 55 of the Western Digital 4CH TRIPLEX user manual — 3. Factory Default
Page 55 · click to enlarge
Page 55
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 55)
Fig. 170 · 3. Factory Default
Page 56 of the Western Digital 4CH TRIPLEX user manual — 5-9. Brightness, Contrast, Hue, Saturation & Alpha-
Page 56 · click to enlarge
Page 56

5-9. Brightness, Contrast, Hue, Saturation & Alpha-

blending Adjustment

Press the MISC button twice to go to the screen where brightness, contrast and alpha-blending

can be adjusted.

Western Digital 4CH TRIPLEX — 5-9. Brightness, Contrast, Hue, Saturation & Alpha- diagram (page 56)
Fig. 171 · 5-9. Brightness, Contrast, Hue, Saturation & Alpha-
Western Digital 4CH TRIPLEX — 5-9. Brightness, Contrast, Hue, Saturation & Alpha- diagram (page 56)
Fig. 172 · 5-9. Brightness, Contrast, Hue, Saturation & Alpha-
Western Digital 4CH TRIPLEX — 5-9. Brightness, Contrast, Hue, Saturation & Alpha- diagram (page 56)
Fig. 173 · 5-9. Brightness, Contrast, Hue, Saturation & Alpha-
Western Digital 4CH TRIPLEX — 5-9. Brightness, Contrast, Hue, Saturation & Alpha- diagram (page 56)
Fig. 174 · 5-9. Brightness, Contrast, Hue, Saturation & Alpha-
Western Digital 4CH TRIPLEX — 5-9. Brightness, Contrast, Hue, Saturation & Alpha- diagram (page 56)
Fig. 175 · 5-9. Brightness, Contrast, Hue, Saturation & Alpha-
Western Digital 4CH TRIPLEX — 5-9. Brightness, Contrast, Hue, Saturation & Alpha- diagram (page 56)
Fig. 176 · 5-9. Brightness, Contrast, Hue, Saturation & Alpha-
Western Digital 4CH TRIPLEX — 5-9. Brightness, Contrast, Hue, Saturation & Alpha- diagram (page 56)
Fig. 177 · 5-9. Brightness, Contrast, Hue, Saturation & Alpha-
Western Digital 4CH TRIPLEX — 5-9. Brightness, Contrast, Hue, Saturation & Alpha- diagram (page 56)
Fig. 178 · 5-9. Brightness, Contrast, Hue, Saturation & Alpha-
Western Digital 4CH TRIPLEX — 5-9. Brightness, Contrast, Hue, Saturation & Alpha- diagram (page 56)
Fig. 179 · 5-9. Brightness, Contrast, Hue, Saturation & Alpha-
Western Digital 4CH TRIPLEX — 5-9. Brightness, Contrast, Hue, Saturation & Alpha- diagram (page 56)
Fig. 180 · 5-9. Brightness, Contrast, Hue, Saturation & Alpha-
Western Digital 4CH TRIPLEX — 5-9. Brightness, Contrast, Hue, Saturation & Alpha- diagram (page 56)
Fig. 181 · 5-9. Brightness, Contrast, Hue, Saturation & Alpha-
1. BTIGHTNESS – to adjust the BRIGHTNESS of the selected channel using

buttons.

2. CONTRAST – to adjust the CONTRAST level of the selected channel using

buttons.

3. HUE – to adjust the CONTRAST level of the selected channel using

buttons.

4. SATURATION – to adjust the CONTRAST level of the selected channel using

buttons.

5. ALPHABLENDING – to adjust the ALPHABLENDING of the selected channel’s status icon

buttons.

using

Page 57 of the Western Digital 4CH TRIPLEX user manual — motion detection regions per channel. 5-11-1. Region Setup
Page 57 · click to enlarge
Page 57

5-10. OSD position and Screen size Adjustment

The position of OSD on LIVE screen can be adjusted up and down.

Depending on the characteristics of the monitor, being able to adjust the position of OSD and

Screen Size may be a very useful feature.

Western Digital 4CH TRIPLEX — 5-10. OSD position and Screen size Adjustment diagram (page 57)
Fig. 182 · 5-10. OSD position and Screen size Adjustment
Western Digital 4CH TRIPLEX — 5-10. OSD position and Screen size Adjustment diagram (page 57)
Fig. 183 · 5-10. OSD position and Screen size Adjustment
Western Digital 4CH TRIPLEX — 5-10. OSD position and Screen size Adjustment diagram (page 57)
Fig. 184 · 5-10. OSD position and Screen size Adjustment
Western Digital 4CH TRIPLEX — 5-10. OSD position and Screen size Adjustment diagram (page 57)
Fig. 185 · 5-10. OSD position and Screen size Adjustment
Western Digital 4CH TRIPLEX — 5-10. OSD position and Screen size Adjustment diagram (page 57)
Fig. 186 · 5-10. OSD position and Screen size Adjustment

5-10-1. Adjusting OSD Ceiling & Bottom Line

Place the cursor on CEILING/BOPTTOM LINE and then use

and SEL button, and the

dark horizontal line across the top/bottom of the screen to adjust the OSD position.

Western Digital 4CH TRIPLEX — 5-10-1. Adjusting OSD Ceiling & Bottom Line diagram (page 57)
Fig. 187 · 5-10-1. Adjusting OSD Ceiling & Bottom Line

5-10-2. Adjusting Screen size

If your monitor does not display verges of screen, you can make the screen size shrunk.

Select SCREEN SIZE menu and then set screen size with SEL button.

5-11. Motion Detection Region Setup

MUX recording mode not only allows full screen motion detection but also lets you assign 4

motion detection regions per channel. 5-11-1. Region Setup

1. Select INDIVIDUAL on REGION field in the MOTION menu and press SEL button to go

to Motion Region Setting screen.

Page 58 of the Western Digital 4CH TRIPLEX user manual — 3. Factory Default
Page 58 · click to enlarge
Page 58
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 58)
Fig. 188 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 58)
Fig. 189 · 3. Factory Default
2. From 1. GREEN 2. ORANGE 3. MINT 4. VIOLET, select the region you wish to adjust.

Place the cursor on “1.Set” and press SEL button to obtain a box that lets you select a

region.

Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 58)
Fig. 190 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 58)
Fig. 191 · 3. Factory Default
3. Move the cursor using

buttons to select the desired region.

Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 58)
Fig. 192 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 58)
Fig. 193 · 3. Factory Default
4. After selecting a region, press SEL button and save the region data.
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 58)
Fig. 194 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 58)
Fig. 195 · 3. Factory Default
5. Press the ESC button to go back to Motion Region Setting screen.
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 58)
Fig. 196 · 3. Factory Default
Page 59 of the Western Digital 4CH TRIPLEX user manual — 5-12-1. Audio Setup and Connection
Page 59 · click to enlarge
Page 59

5-11-2. Deleting Region

1. Select INDIVIDUAL for REGION in the MOTION menu and press SELECT button to go

to Motion Region Setting screen.

Western Digital 4CH TRIPLEX — 5-11-2. Deleting Region diagram (page 59)
Fig. 197 · 5-11-2. Deleting Region
2. From 1. GREEN 2. ORANGE 3. MINT 4. VIOLET, select the region you wish to delete.

Place the cursor on “2.DELETE” and press SEL button. When DVR asks “Do you Delete

This Region Data?” select “YES” to delete the selected region. A mode for setting a new

region will proceed.

Western Digital 4CH TRIPLEX — 5-11-2. Deleting Region diagram (page 59)
Fig. 198 · 5-11-2. Deleting Region
Western Digital 4CH TRIPLEX — 5-11-2. Deleting Region diagram (page 59)
Fig. 199 · 5-11-2. Deleting Region

5-12. Audio

5-12-1. Audio Setup and Connection

1. Connect the audio input and audio output cable to the audio connection port on the back

of DVR.

2. In CHANNEL menu of MUX menu, select the desired audio input channel for each video

channel by highlighting it yellow.

Western Digital 4CH TRIPLEX — 5-12-1. Audio Setup and Connection diagram (page 59)
Fig. 200 · 5-12-1. Audio Setup and Connection
3. When recording by sensor, motion detection, manual or schedule begins, on a channel

that the audio is linked to, audio recording begins automatically.

Page 60 of the Western Digital 4CH TRIPLEX user manual — 5-12-2. Playback
Page 60 · click to enlarge
Page 60
4. In MUX recording mode, if you wish to listen to the audio of a channel live, select the

channel from live screen using the number buttons. (The channel label becomes

highlighted yellow as bellow). Audio live is not available for listening when the SETUP

menu is being set up.

5-12-2. Playback

1. Connect the audio cable to the audio output port on the back of DVR.
2. Check the status part where audio is recorded (highlighted in yellow) from the SEARCH

menu. (Audio field will be highlighted in yellow even when only one channel is

recorded.)

Western Digital 4CH TRIPLEX — 5-12-2. Playback diagram (page 60)
Fig. 201 · 5-12-2. Playback
3. Use

buttons and SEL button to select the date, channel and time you wish

to play. Press the PLAY/PAUSE button to play the audio with video.

Page 61 of the Western Digital 4CH TRIPLEX user manual — 5-13-2. RS-422/485
Page 61 · click to enlarge
Page 61

5-13. External Terminal Information

5-13-1. RS-232C

Western Digital 4CH TRIPLEX — 5-13-1. RS-232C diagram (page 61)
Fig. 202
Western Digital 4CH TRIPLEX — 5-13-1. RS-232C diagram (page 61)
Fig. 203

1 DCD Data Carrier Detect 6 DSR Data Set Ready 2 RxD Receive Data 7 RTS Request to Send 3 TxD Transmit Data 8 CTS Clear to Send 4 DTR Data Terminal Ready 9 RI Ring Indicator 5 GND Signal Ground

5-13-2. RS-422/485

Western Digital 4CH TRIPLEX — 5-13-2. RS-422/485 diagram (page 61)
Fig. 204

No Name Description (RS-422) 1 NC Not Connected. 2 RxD+ Receive Data+ 3 TxD+ Transmit Data+ 4 TxD- Transmit Data- 5 GND Signal Ground 6 RxD- Receive Data- 7 NC Not Connected. 8 NC Not Connected. 9 NC Not Connected.

Western Digital 4CH TRIPLEX — 5-13-2. RS-422/485 diagram (page 61)
Fig. 205

No Name Description (RS-485) 1 NC Not Connected. 2 NC Not Connected. 3 TxD+ Transmit Data+ 4 TxD- Transmit Data- 5 GND Signal Ground 6 NC Not Connected. 7 NC Not Connected. 8 NC Not Connected. 9 NC Not Connected.

Page 62 of the Western Digital 4CH TRIPLEX user manual — 5-15-1. Back up in CD
Page 62 · click to enlarge
Page 62

5-14. Sensor Installation

DVR can connect up to 4sensors. There are two simple steps to install the sensors.

z Connect THE SENSOR SIGNAL LINE

z Connect the sensor power line (10~12V)

Western Digital 4CH TRIPLEX — 5-14. Sensor Installation diagram (page 62)
Fig. 206 · 5-14. Sensor Installation

Vice versa connection of Positive and Negative will occur a fatal error or a malfunction of DVR.

5-15. Video back up in CD (Available only in model with CD-RW)

5-15-1. Back up in CD

1. Please go to “STORAGE” in the SETUP menu.
2. And then go to CD-RW BACKUP and place the cursor “SELECT” and press SEL button.

The window for CD back up will appear as bellow. Please set the channels and time to

backup.

Page 63 of the Western Digital 4CH TRIPLEX user manual — 5-15-2. Playback Data in CD
Page 63 · click to enlarge
Page 63
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 63)
Fig. 207 · 3. Factory Default
3. If the recorded data on DVR is QUAD mode, you need to select Q on VIDEO. If you do

not select Q, QUAD mode will not be backed up on the CD.

4. If the selected data volume exceeds CD media size, you need to put another CD in. And

then DVR automatically proceeds backing up from the end of the data of the previous

CD.

5. BACKUP is completed, the following message will appear.
6. BACKUP is failed, the following message will appear.

When user proceeds CD-RW BACKUP, all the other functions such as networking and

recording will be on hold.

5-15-2. Playback Data in CD

1. Please put CD in CD-RW in PC.
2. Please start Network Client S/W.
3. Please go to SEARCH and select PLAYBACK VIDEO button.

window will pop-up.

Western Digital 4CH TRIPLEX — 5-15-2. Playback Data in CD diagram (page 63)
Fig. 208 · 5-15-2. Playback Data in CD
4. Please select and open the backed up data.

The file format of the backed up data is *.nsf. You can review and playback the backed

up data on CD only in Network Client S/W.

And then Search

Page 64 of the Western Digital 4CH TRIPLEX user manual — 6. HDD Installation
Page 64 · click to enlarge
Page 64

6. HDD Installation

6-1. Installing HDD in removable HDD rack

For DVR, the hard disk, on which images are saved, is installed into the RACK.

The hard disk is installed into DVR as shown in the following instructions.

1. Prepare a hard disk and rack as shown below.
Western Digital 4CH TRIPLEX — 6. HDD Installation diagram (page 64)
Fig. 209 · 6. HDD Installation
2. Set the hard disk to master. (Refer to the JUMPER SETTING of the hard disk being
Western Digital 4CH TRIPLEX — 6. HDD Installation diagram (page 64)
Fig. 210 · 6. HDD Installation
3. Open the upper cover of the rack and connect the power cable and data cable of the

hard disk and the rack.

Western Digital 4CH TRIPLEX — 6. HDD Installation diagram (page 64)
Fig. 211 · 6. HDD Installation
4. Put the cover back on as shown.
Western Digital 4CH TRIPLEX — 6. HDD Installation diagram (page 64)
Fig. 212 · 6. HDD Installation
5. Tighten the clamping screws on both sides of the rack.

installed)

Page 65 of the Western Digital 4CH TRIPLEX user manual — 6-2. HDD Jumper Setting
Page 65 · click to enlarge
Page 65
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 65)
Fig. 213 · 3. Factory Default
6. Assemble the rack containing the hard disk into DVR while holding up the handle.
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 65)
Fig. 214 · 3. Factory Default
7. Have the rack fixed in using the key of the rack. Otherwise, “HDD INSTALLATION

FAILURE” message will pop-up.

Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 65)
Fig. 215 · 3. Factory Default
8. If the hard disk is not formatted and recognizable by DVR, an automatic formatting will

be done when the power of DVR is turned on. The notice “FORMATING” will appear on

the screen as shown below during formatting.

6-2. HDD Jumper Setting

DVR allows on one hard disk to be assembled into the REMOVEBLE HDD RACK and a new

hard disk’s JUMPER SETTING should be set to either SINGLE or MASTER. All hard disks

provide information needed for JUMPER SETTING on the hard disks’ exterior. Please beware

that DVR will not run properly without a proper JUMPER SETTING.

Refer to the following homepages of major hard disk manufacturers of additional information on

JUMPER SETTING.

z WESTERN DIGITALwww.westerndigital.com
z SEAGATEwww.seagate.com
z HITACHIwww.hgst.com
z MAXTERwww.maxter.com
Page 66 of the Western Digital 4CH TRIPLEX user manual — WARNING
Page 66 · click to enlarge
Page 66

6-3. HDD Indicator

When the POWER is on, the hard disk indicator is displayed as the chart shows.

ITEM INDICATOR POWER GREEN LED HDD ACCESS YELLOW LED

Western Digital 4CH TRIPLEX — 6-3. HDD Indicator diagram (page 66)
Fig. 216 · 6-3. HDD Indicator

WARNING

1. DVR must be turned off when one installs a hard disk into DVR.
2. DVR must be turned off when changing hard disk.
3. The system will recognize HDD installed only when the key of the rack must

be locked.

Page 67 of the Western Digital 4CH TRIPLEX user manual — 7-3-1. Network ACCESS ON/OFF
Page 67 · click to enlarge
Page 67

7. NETWORKING

DVR can be connected to LAN or ADSL network and supports functions and additional features

that are available on remote DVR.

7-1. NETWORK CLIENT S/W Main Features

z Remote real-time monitoring

z Remote search and playback of saved data in DVR

z Various BACKUP functions – Image data backup during remote live display or remote

playback, directly download image data from a remote DVR.

z Remote camera control

z Supports dynamic IP addresses

7-2. Computer System Requirements

z Operating SystemMicrosoft Windows 98/SE, Microsoft Windows ME, Microsoft

Windows 2000, or Microsoft Windows XP

z CPUPentium III (Celeron) 1.6GHz or higher
z RAM128MB or higher

NETWORK CLIENT S/W may not operate if the VGA card in PC is outmoded or is not well-

known brand.

7-3. Network Setup in DVR

To make regular use of NETWORK CLIENT S/W, the network type of DVR must be set same as

the connected network after setting Network Access “ON”. DVR supports various types of

network including dynamic IP and static IP environments.

For details regarding network environments and related numbers, please consult the network

administrator of the installed site.

7-3-1. Network ACCESS ON/OFF

1. Select NETWORK in the SETUP menu to set up your network.
2. CLIENT S/W ACCESS can be turned ON/OFF. CLIENT ACCESS must be turned ON for

network to be connected from CLIENT to DVR.

z Remote setup

Page 68 of the Western Digital 4CH TRIPLEX user manual — 7-3-3. For LAN –DHCP Users
Page 68 · click to enlarge
Page 68
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 68)
Fig. 217 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 68)
Fig. 218 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 68)
Fig. 219 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 68)
Fig. 220 · 3. Factory Default

7-3-2. For LAN Users

Select LAN for NETWORK TYPE using

buttons. Edit the IP address assigned from

LAN as well as LAN’s GATEWAY and SUBNET MASK. Use

buttons to edit the

buttons to move from field to field.

Western Digital 4CH TRIPLEX — 7-3-2. For LAN Users diagram (page 68)
Fig. 221 · 7-3-2. For LAN Users
Western Digital 4CH TRIPLEX — 7-3-2. For LAN Users diagram (page 68)
Fig. 222 · 7-3-2. For LAN Users

For details regarding IP ADDRESS, GATEWAY, and SUBNET MASK, please consult the

network administrator of the installed site.

7-3-3. For LAN –DHCP Users

1. If LAN is using DHCP, set DHCP to “ON”.

For DHCP installation, please refer to “4-7-3. LAN Setup –DHCP (Dynamic Host

Configuration Protocol)”.

2. Set up the email address that will send out the assigned IP address of DVR, and the

related Mail Server’s IP address in the INFO menu.

numbers and use

Page 69 of the Western Digital 4CH TRIPLEX user manual — 7-3-4. For ADSL (Dynamic IP address) Users
Page 69 · click to enlarge
Page 69
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 69)
Fig. 223 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 69)
Fig. 224 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 69)
Fig. 225 · 3. Factory Default

For setting up an email address for sending out assigned IP addresses to the client user,

please refer to “4-5-5. SEND MAIL (IP ADDRESS Mailing)”.

IMPORTANT

To receive e-mail with Dynamic IP address from DVR, User has to apply IP address of Mail

Server run by Manufacturer on the field of “MAIL SERVER IP”.

7-3-4. For ADSL (Dynamic IP address) Users

1. If you are using ADSL, change the NETWORK TYPE to ADSL.

Enter the service ID and password of ADSL using the keyboard shown below.

Western Digital 4CH TRIPLEX — 7-3-4. For ADSL (Dynamic IP address) Users diagram (page 69)
Fig. 226 · 7-3-4. For ADSL (Dynamic IP address) Users

Consult the ADSL service administrator for ID and password.

3. Set up the email address that will send out the assigned IP address of DVR, and the

related Mail Server’s IP address in the INFO menu.

Page 70 of the Western Digital 4CH TRIPLEX user manual — 7-4-2. NETWORK CLIENT S/W Start Up – Static IP Address
Page 70 · click to enlarge
Page 70
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 70)
Fig. 227 · 3. Factory Default

For setting up an email address for sending out assigned IP addresses to the client user, please

refer to “4-5-5. SEND MAIL (IP ADDRESS Mailing)”.

IMPORTANT

To receive e-mail with Dynamic IP address from DVR, User has to apply IP address of Mail

Server run by Manufacturer on the field of “MAIL SERVER IP”.

7-4. NETWORK CLIENT S/W Installation and Start Up

7-4-1. NETWORK CLIENT S/W Installation

Do the following before starting installation.

z Close all programs that are operating on the computer before installing Network Client

S/W.

z If there is an existing Network Client S/W on the computer, uninstall the older version.

Insert the enclosed CD-ROM into the PC’s CD-ROM, and run the file named ‘DVR.exe’ to begin

the installation of Network Client S/W. The icon shown below is created when the installation of

Network Client S/W is completed.

7-4-2. NETWORK CLIENT S/W Start Up – Static IP Address

1. Run CLIENT S/W and press the SITE button. A dialogue box for entering IP address and

password appears.

Page 71 of the Western Digital 4CH TRIPLEX user manual — 3. Factory Default
Page 71 · click to enlarge
Page 71
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 71)
Fig. 228 · 3. Factory Default
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 71)
Fig. 229 · 3. Factory Default
2. Enter the assigned IP address from DVR setup menu into the IP ADDRESS field and enter

the password if DVR is using a password. After pressing OK, the LIVE screen appears after

it has been connected to the network. 7-4-3. NETWORK CLIENT S/W Start Up – Dynamic IP Address

1. If DVR is connected to LAN-DHCP or ADSL, identify the IP address that has been sent to

the established email address.

2. Run NETWORK CLIENT S/W and press the SITE button. A dialogue box for entering IP

address and password appears.

Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 71)
Fig. 230 · 3. Factory Default
3. Enter the IP address received through the established email address into the IP ADDRESS

field and enter the password if DVR is using a password. After pressing OK, the LIVE screen

appears after it has been connected to the network.

Page 72 of the Western Digital 4CH TRIPLEX user manual — 11. CONTROL (ALARM OUT)
Page 72 · click to enlarge
Page 72

7-5.LIVE

Western Digital 4CH TRIPLEX — 7-5.LIVE diagram (page 72)
Fig. 231
1. Enlarge Channel
2. QUAD Screen ROTATE Screen
3. Display Live Images on Full-screen without any control tools
4. IP Address Displayed
5. Date and Time Displayed

6. SITE

7. SEARCH

8. SETUP

9. Remote Camera Control
10. Camera Channels ON/OFF

11. CONTROL (ALARM OUT)

12. SENSOR Indicator
13. Video backup during Live display
14. Still Image backup during live display
15. Select Audio
16. Terminate Network Client S/W
17. Hard Disk in Use
Page 73 of the Western Digital 4CH TRIPLEX user manual — 9 RECORDED BY: SENSOR, MOTION, MANUAL
Page 73 · click to enlarge
Page 73

7-6. SETUP

Press the SETUP button on the upper right of GUI to go to remote DVR SETTING menu.

Western Digital 4CH TRIPLEX — 7-6. SETUP diagram (page 73)
Fig. 232

7-6-1. RECORD

A. SELECT MODE

You can select your recording mode here; the selected mode is inversed.

¾ MUX – Record in MUX mode (inversed during MUX recording)

¾ QUAD – Record in QUAD mode

¾ SCHEDULE – Record in SCHEDULE mode

Western Digital 4CH TRIPLEX — A. SELECT MODE diagram (page 73)
Fig. 233

Please refer to “4-3-1. Selecting Recording Mode (QUAD, MUX, SCHEDULE)”.

B. MUX SETTING

¾ RESOLUTIONSelect from 720 X 480 and 360 X 240
¾ QUALITYSelect quality among LOW / NORMAL / HIGH
¾ AUDIOSetup Volume Control and INPUT GAIN

¾ CH1 / CH2 / CH3 / CH4

— CHANNEL

9 FRAME RATESelect recording frame rate

9 RECORDED BY: SENSOR, MOTION, MANUAL

9 RECORD AUDIO: NONE, 1, 2, 3, 4

9 NET FRAME DROP

— MOTION

9 FULL MOTION REGIONFull-screen Motion Detect Mode
9 SET REGIONInversed when motion detection region is being setup
9 RELAY OUTPUT - ALARMSelect alarm
Page 74 of the Western Digital 4CH TRIPLEX user manual — — RELAY OUTPUT
Page 74 · click to enlarge
Page 74

9 SENSIVITY – Select from LOW, NORMAL, and HIGH

¾ SENSOR1 / SENSOR2 / SENSOR3 / SENSOR4

— TYPESelect from NORMAL OPEN / NORMAL CLOSE

— RELAY OUTPUT

9 ALARMSelect alarm to be set off when the sensor is activated
9 CHANNELSelect channel to be recorded when the sensor is activated
9 DURAITONSelect the duration of recording when the sensor is activated
Western Digital 4CH TRIPLEX — — RELAY OUTPUT diagram (page 74)
Fig. 234

Please refer to “4-3-3 MUX Recording Mode”.

C. QUAD SETTING

¾ QUALITYSelect quality among LOW / NORMAL / HIGH
¾ AUDIOSetup Volume Control and Input Gain

¾ CHANNEL & MOTION

— AVAILABLE FRAME RATEUsable Frame
— FRAME RATESelect recording frame rate

— RECORDED BY: SENSOR, MOTION, MANUAL

— SENSOR PRERECORD

— RECORD AUDIO: NONE, 1, 2, 3, 4

— NET FRAME DROP

— RELAY OUTPUT - ALARMSelect alarm to be set off when motion is detected

— SENSIVITY – Select from LOW, NORMAL, and HIGH

¾ SENSOR1 / SENSOR2 / SENSOR3 / SENSOR4

— TYPESelect from NORMAL OPEN / NORMAL CLOSE

— RELAY OUTPUT

Page 75 of the Western Digital 4CH TRIPLEX user manual — D. SCHEDULE SETTING
Page 75 · click to enlarge
Page 75
9 ALARMSelect the alarm to be set off when Sensor is activated
9 CHANNELSelect the channel to be recorded when Sensor is activated
9 DURATIONSelect the duration of alarm and recording time when Sensor is
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 75)
Fig. 235 · 3. Factory Default

Please refer to “4-3-2. QUAD Recording Mode”.

D. SCHEDULE SETTING

Western Digital 4CH TRIPLEX — D. SCHEDULE SETTING diagram (page 75)
Fig. 236

The schedule setup and usage instruction are the same as DVR.

Please refer to “4-3-4. SCHEDULE Recording Mode” for more

instructions.

activated

Page 76 of the Western Digital 4CH TRIPLEX user manual — ¾ OLD PASSWORD
Page 76 · click to enlarge
Page 76

7-6-2. LIVE

D. CH1 / CH2 / CH3 / CH4

¾ LABELShow the selected channel name
¾ P/T/Z/F TYPESelect the appropriate camera protocol for the channel

E. ROTATION SETTING

¾ CHANNELSelect a channel to rotate

¾ DURATION: Select the time interval between each channel for automatic channel rotation.

Western Digital 4CH TRIPLEX — E. ROTATION SETTING diagram (page 76)
Fig. 237

Please refer to “4-2. LIVE”

7-6-3. SYSTEM

A. SYSTEM INFORMATION

¾ SITE DECSRIPTION: Edit DVR information of DVR that is connected to network.

¾ IP ADDRESSShow IP Address of the appropriate site
¾ SERIAL IDShow the serial number for DVR that is connected to network
¾ S/W VERSIONShows the S/W version of DVR that is connected to network
¾ H/W VERSIONShows the H/W version of DVR that is connected to network
¾ Client VERSIONShow the client S/W version

B. USER PASSWORD (PASSWORD Edit Menu)

¾ OLD PASSWORD

¾ NEW PASSWORD

¾ COMFIRM PASSWORD

C. TIME ZONE

D. DAY LIGHT SAVING (DLS) SETTING

Page 77 of the Western Digital 4CH TRIPLEX user manual — ¾ IP ADDRESS:
Page 77 · click to enlarge
Page 77
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 77)
Fig. 238 · 3. Factory Default

ADMIN password can’t be amended on Network Client S/W.

7-6-4. NETWORK

A. ADSL SETTINGS

¾ SERVICE IDEnter ADSL service ID
¾ PASSWORDEnter ADSL password

B. LAN SETTING

¾ USE DHCPSelect to use DHCP

¾ IP ADDRESS:

¾ GATEWAY

¾ SUBNET MASK

C. NETWORK UPGRADE

Western Digital 4CH TRIPLEX — ¾ IP ADDRESS: diagram (page 77)
Fig. 239
Page 78 of the Western Digital 4CH TRIPLEX user manual — 7-6-6. Saving and Uploading Settings
Page 78 · click to enlarge
Page 78

7-6-5. BACKUP

Western Digital 4CH TRIPLEX — 7-6-5. BACKUP diagram (page 78)
Fig. 240

Available backup file format

*.nsf – This format can be playback only in network client S/W.

*.avi – This format can be playback only in Media Player.

7-6-6. Saving and Uploading Settings

1. Saving Settings

If you wish to use the current settings later on, customize the settings and press the

SAVE button at the bottom left corner. Save the file on the computer. (File Format: ndc)

Western Digital 4CH TRIPLEX — 7-6-6. Saving and Uploading Settings diagram (page 78)
Fig. 241 · 7-6-6. Saving and Uploading Settings
2. Uploading the saved settings

If you wish to use the saved setting, press the LOAD button on the bottom left corner.

Select the setting you wish to use and the setting is applied to DVR.

Page 79 of the Western Digital 4CH TRIPLEX user manual — 7-7-1. Buttons in Search menu
Page 79 · click to enlarge
Page 79

7-7. SEARCH

Western Digital 4CH TRIPLEX — 7-7. SEARCH diagram (page 79)
Fig. 242

7-7-1. Buttons in Search menu

1. Enlarge the selected channel on display
2. The Graphic Bar shows the recorded part for the day in Pink (MUX Record) and

Green (QUAD).

Western Digital 4CH TRIPLEX — 7-7-1. Buttons in Search menu diagram (page 79)
Fig. 243 · 7-7-1. Buttons in Search menu
3. Time Select Bar (Move the bar to the part you wish to play).
4. AUDIO, SENSOR, MOTION – Each bar shows audio, sensor, and motion in
5. PLAY button
6. PAUSE button
7. Indicate the 1,2 graphic by hour
Western Digital 4CH TRIPLEX — 7-7-1. Buttons in Search menu diagram (page 79)
Fig. 244 · 7-7-1. Buttons in Search menu
8. Disconnect
9. Button to go to Live window
10. Button to go to SETUP window
11. Select Date for Search button
12. Video BACKUP during playback

recording

Page 80 of the Western Digital 4CH TRIPLEX user manual — NOTE
Page 80 · click to enlarge
Page 80
13. Still image capture during playback
14. Playing audio of selected playback channel
15. 4channels simultaneous playback
16. Browsing and playback the backup video
17. Download still images from DVR

7-7-2. Search when DVR has two HDD

18. BACKUP through Time Setting from DVR
1. Press SEARCH button. Then the window will appear.
Western Digital 4CH TRIPLEX — 7-7-2. Search when DVR has two HDD diagram (page 80)
Fig. 245 · 7-7-2. Search when DVR has two HDD
2. Select HDD to search and playback.

7-8. BACK UP

7-8-1. Video BACKUP during LIVE DISPLAY

1. During LIVE DISPLAY, press the channel button you wish to backup. The button will

turn red and starts backup is proceeded.

2. Press the same button again at the point where you wish to stop BACKUP. A window

where you can save the Backup Data in DVR will appear.

Western Digital 4CH TRIPLEX — 7-8-1. Video BACKUP during LIVE DISPLAY diagram (page 80)
Fig. 246 · 7-8-1. Video BACKUP during LIVE DISPLAY
3. Enter file name (file format: avi) and press “Save”.

NOTE

To save audio data along with video data, press and activate Audio button before pressing

Video Backup button.

Page 81 of the Western Digital 4CH TRIPLEX user manual — 7-8-2. STILL IMAGE capture during LIVE DISPLAY
Page 81 · click to enlarge
Page 81

7-8-2. STILL IMAGE capture during LIVE DISPLAY

1. During LIVE DISPLAY, press the channel button you wish to backup.
2. A window for saving the image will appear.
3. Enter file name (file format: bmp or jpg) and press “Save”. 7-8-3 Video BACKUP during Playback
1. From the SEARCH Menu, press the channel button you wish to back up. The channel

button will turn red and backup is proceeded.

2. Press the same button again at the point where you wish to stop BACKUP. A window

where you can save the Backup Data on the computer will appear.

Western Digital 4CH TRIPLEX — 7-8-2. STILL IMAGE capture during LIVE DISPLAY diagram (page 81)
Fig. 247 · 7-8-2. STILL IMAGE capture during LIVE DISPLAY
3. Enter file name (file format: avi) and press “Save”. 7-8-4. STILL IMAGE capture during Playback
1. During Playback, press the channel button you wish to backup.
2. A window for saving the image will appear.
Page 82 of the Western Digital 4CH TRIPLEX user manual — 7-8-6. BACKUP through Time Setting
Page 82 · click to enlarge
Page 82
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 82)
Fig. 248 · 3. Factory Default
3. Enter file name (file format: bmp) and press “Save”. 7-8-5. Downloading Still Images from DVR
1. Press the following button to download the still image, which is saved in DVR, through

the network.

2. When the Download window appears, select the desired file from the list on the left and

move it to the list on the right. Select the folder to save from DIRECTORY and press

SAVE to start downloading.

Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 82)
Fig. 249 · 3. Factory Default

7-8-6. BACKUP through Time Setting

1. Press the following button to backup by setting a specified time.
2. A window for where you can select the time period will appear.
Western Digital 4CH TRIPLEX — 7-8-6. BACKUP through Time Setting diagram (page 82)
Fig. 250 · 7-8-6. BACKUP through Time Setting
3. Select the desired time.
4. Select a folder and make a file name of backup data by pressing the BROWSE button.
Page 83 of the Western Digital 4CH TRIPLEX user manual — 7-8-7. Converting <nsf> CD backup format to <avi> format
Page 83 · click to enlarge
Page 83
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 83)
Fig. 251 · 3. Factory Default
5. Select the channel to backup.
6. Backup starts when you press START
Western Digital 4CH TRIPLEX — 3. Factory Default diagram (page 83)
Fig. 252 · 3. Factory Default
7. When BACKUP is completed, “Backup complete” will appear.

7-8-7. Converting <nsf> CD backup format to <avi> format

1. Search and playback backup file in “nsf” format.
2. During playback, press the channel button when you wish to convert. Then button color

becomes Red.

3. Press the channel button when you wish to finish converting.
4. A window for saving the image will appear.
Western Digital 4CH TRIPLEX — 7-8-7. Converting <nsf> CD backup format to <avi> format diagram (page 83)
Fig. 253 · 7-8-7. Converting <nsf> CD backup format to <avi> fo…
5. Enter file name and press “Save”.
Page 84 of the Western Digital 4CH TRIPLEX user manual — NOTE
Page 84 · click to enlarge
Page 84

8. Networking by Web Browser

8-1. Download Web Brower Viewer and Connection

1. Enter the DVR IP address. Then the window will appear as bellow. Click “YES” to

download Web Browser Viewer from the server run by the manufacturer.

Western Digital 4CH TRIPLEX — 8. Networking by Web Browser diagram (page 84)
Fig. 254 · 8. Networking by Web Browser

NOTE

Web Browser Viewer is to be downloaded from the server run by the manufacturer, not from DVR.

In other words, PC and DVR should be linked with Internet in order to use Web Brower networking.

2. Web Browser Viewer will be downloaded and installed. A dialogue box for entering IP

address and password will appear.

Western Digital 4CH TRIPLEX — NOTE diagram (page 84)
Fig. 255
3. Enter IP address and the password and click the “Connect” button.
Page 85 of the Western Digital 4CH TRIPLEX user manual — 8-2-2. SEARCH
Page 85 · click to enlarge
Page 85

8-2. Main Features

8-2-1. LIVE

Western Digital 4CH TRIPLEX — 8-2-1. LIVE diagram (page 85)
Fig. 256

8-2-2. SEARCH

Western Digital 4CH TRIPLEX — 8-2-2. SEARCH diagram (page 85)
Fig. 257
Page 86 of the Western Digital 4CH TRIPLEX user manual — NOTE
Page 86 · click to enlarge
Page 86

8-2-3. BACKUP

Western Digital 4CH TRIPLEX — 8-2-3. BACKUP diagram (page 86)
Fig. 258

9. Networking by DDNS (Dynamic Domain Name

Server)

1. Check the serial number of DVR from SETUP>INFO>SYSTEM>SERIAL ID.
2. Please contact a distributor or an installer to register the DVR on DDNS Server.
3. Register your own domain name on DDNS Server.

NOTE

If your own domain name and serial ID of DVR are registered at DDNS server run by

manufacturer, IP address of DDNS Server run by Manufacturer should be applied on DDNS

SERVER IP filed.

If your own domain name and serial ID of DVR are registered at DDNS server run by

distributor, Please ask the distributor IP address of DDNS Server and apply it on DDNS

SERVER IP filed.

4. After your own domain name and serial ID of DVR are registered at DDNS server, user

can access network with your own domain name.

Page 87 of the Western Digital 4CH TRIPLEX user manual — 11. Network access beyond Rauter
Page 87 · click to enlarge
Page 87

10. Playback of local HDD in Network Client S/W

1. Take HDD out from DVR and connect it to PC as Slave.
2. Please go to CMOS setup and confirm that CMOS recognizes HDD and its size or not.
3. Save CMOS setting and boot PC.
4. Run Network Client S/W.
5. Press SEARCH button and then SITE button of Network Client S/W.
6. Type “127.0.0.1” in IP field of window.
7. All functionality of playback is the same as remote HDD search.

11. Network access beyond Rauter

In order to access beyond Rauter (Firewall), user must open 20 TCP ports for Command level,

Live channels, and Storage channels. If these all ports are not open properly, user can not

access DVR beyond a rauter.

If DVR sets port number with 4456 as bellow, user has to open 20 TCP ports from 4456 to

If DVR sets port number with 1111, user has to open 20 TCP ports from 1111 to 1130.

In order to access network, user has to enter “External IP Address:xxxx” (Ex.

111.222.333.444:4456) in the field of “Server address”

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Western Digital 4CH TRIPLEX

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Western Digital 4CH TRIPLEX

Be the first to ask — other owners or our team will answer.

Original document

Western Digital 4CH TRIPLEX manual PDF

87 pages·3.5 MB·DVR·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…