Instruction/ maintenance manual of the product C-1000A Viking Electronics
Go to page of 8
The C-1000A Controller dramatically expands the potential installation sites for many peripher- als such as doorboxes and paging amplifiers. Doorboxes and paging amplifiers can now be used on single l.
I I n n s s t t a a l l l l a a t t i i o o n n a a n n d d A A p p p p l l i i c c a a t t i i o o n n s s A. One or T wo Doorboxes Sharing a Phone Line VIKING © MODEL C-1000A VIKING ELECTRONICS HUDSON, WI 54016 DOOR ENTRY/P AGING CONTROLLER POWER 13.
The C-1000A can also be used without a C.O. line. This is ideal for connecting the C-1000A to an unused trunk/line input of your phone system or connecting to phones used only for doorbox communication. 1. Connect the power , required doorboxes, and doorstrike out- puts (if required) as shown in section A .
G . Adding Paging to Homes and Small Businesses with Single Line Phones The C-1000A can be used to control a paging amplifier from a single phone line. The amplifier used must provide talk battery , such as the P A-2A ( Fax Back Document 485 ) or CP A-7B ( Fax Back Document 455 ).
P P r r o o g g r r a a m m m m i i n n g g A. Accessing the Programming Mode 2. Accessing the Programming Mode Remotely a. Call into the C-1000A from a T ouch T one phone. Note: Call in from another line to avoid C.O. busy signals,etc. b. Answer the call using the device on the “ PHONES ” port.
O O p p e e r r a a t t i i o o n n A. Doorbox Controller A visitor pressing the “Call” button will cause the phones connected to the “PHONES” port to ring. Simply answer your phone to converse with the visitor . G . N.O./N.C. Cont act Selection F .
If a C.O. line call is in progress and a doorbox is activated, a single or double “call waiting” tone will be heard indi- cating doorbox 1 or doorbox 2 is calling. T o place the in-progress call on hold and answer the calling doorbox, sim- ply dial a T ouch T one “ # ”, pulse dial a “ 2 ” or hook flash twice.
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and it s affiliates and/or subsidiaries assume no responsibility for errors and omissions contained in this information.
An important point after buying a device Viking Electronics C-1000A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Viking Electronics C-1000A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Viking Electronics C-1000A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Viking Electronics C-1000A you will learn all the available features of the product, as well as information on its operation. The information that you get Viking Electronics C-1000A will certainly help you make a decision on the purchase.
If you already are a holder of Viking Electronics C-1000A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Viking Electronics C-1000A.
However, one of the most important roles played by the user manual is to help in solving problems with Viking Electronics C-1000A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Viking Electronics C-1000A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
