Instruction/ maintenance manual of the product VO27 Vax
Go to page of 14
2 3 c f a d 1 2 3 Putting your cleaner together Remove your Rapide XL from the carton with caution. The handle is connected to the body by a cord. Note : Do not tug or pull on the cord. Line up the handle to the upper body of the machine and slide into place.
4 5 4 5 6 Putting your cleaner together Feed the cord through the slots on the back of the handle and push into place. P lace a nut into the recess in the back of the upper handle. While holding the nut in place insert one of the large screws through the front of the upper handle and tighten.
6 7 2 3 4 T ool storage S lide the tool caddy downwards until it is secured in place. Note : The tool caddy can be removed for storage on a wall. C onnect upholstery attachment to end of hose by pressing until it clicks into place.
8 5 6 Pre-treating your carpets with the pre-treatment wand and solution (model V -027PT only) R emove solution tank cap. C AUTION : Do not overfill. Y ou should leave 1-2 cm of air space. Fill the tank with pre-treatment solution. R eplace the solution tank cap.
10 10 Pre-treating your carpets with the pre-treatment wand and solution (model V -027PT only) Using the wand and the trigger , apply pre-treatment solution to carpets. T urning the spray nozzle clockwise or anti-clockwise will alter the spray pattern.
12 13 4 5 6 How to operate your cleaner R emove solution tank cap. C AUTION : Do not overfill. Y ou should leave 1-2 cm of air space. Fill the tank with V AX AAA Carpet Cleaner . The cleaner can be stored with solution in the solution tank. It does not have to be removed after each use.
14 15 1 2 3 How to operate your cleaner P lug the cord into an electrical socket. Step on the handle release pedal to put the cleaner into a cleaning position. T urn main power switch, brush switch and soap switch all to the ON position. Note : See page 10 for details on the various switch functions.
1 2 3 H ose attachments P ut the cleaner in its upright position. T urn the brush switch and power switch to the off position. R emove the hose from its stored position on the back of the cleaner . Lift the hose attachment cover located on the top of the dirty water tank.
7 8 9 H ose attachments W hile depressing the blue solution spray trigger , pull the attachment in a downward motion. Release the trigger and push the attachment forward in the same path to remove dirty water and solution from upholstery . For heavily soiled areas, repeat if necessary .
1 2 3 E mptying the dirty water tank D epress the dirty water tank latch and simultaneously pull the dirty water tank nozzle tab up and away from the cleaner . R emove the dirty water tank by lifting the dirty water tank handle and pulling the tank out of the base.
7 8 E mptying the dirty water tank R eturn dirty water tank to the base of the cleaner by tipping the nozzle down into the basin and dropping it into place. L ift the front of the cleaner base off the carpeting with one hand. Line up the black tabs with the grooves of the front nozzle.
4 1 B elt or brush removal and replacement 1 . Loop the belt around the rear shaft. 2. Loop the top of the belt above the small pulley and the bottom of the belt around the lower small pulley .
T roubleshooting Problem Cleaner won’t run V acuum won’t pick up/loss of suction W ater escaping from the V acuum Cleaner attachments won’t spray Cleaner won’t dispense solution No soap dispensing Will not dispense water P ossible Cause • Power cord not firmly pushed into a mains socket.
UK SERVICE & HELP - VA X CARE 0870 6061248 Mon-F ri. 9.00am to 5.00pm. An answer phone is a vailable out of these hours. If you have queries or concerns about using your VAX, call the HELPLINE. Calls are charged at the UK national rate. Please make a note of the serial number and model number of your V AX before calling.
An important point after buying a device Vax VO27 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vax VO27 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vax VO27 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vax VO27 you will learn all the available features of the product, as well as information on its operation. The information that you get Vax VO27 will certainly help you make a decision on the purchase.
If you already are a holder of Vax VO27, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vax VO27.
However, one of the most important roles played by the user manual is to help in solving problems with Vax VO27. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vax VO27 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
