Instruction/ maintenance manual of the product Wireless Cable/DSL Router US Robotics
Go to page of 13
Wir eless Cable/DSL R outer Companion R eference Guide R24.0262.00.
1 What Y ou Need to Begin For Broadband Router Functions: • PC with an Ethernet N IC installed or an 802.11b Wireless Adapter installed • A functioning Ethernet-based cable or DSL modem OR an RS-232-based analog or ISDN modem • Operating system installation CD-ROM (i.
3 2 Back View 1. R ESE T Button: Press in and hold the R ES ET button. While holding the RE SET button, unplug then plug back in the power supply . When the Wireless Cable/DSL Router has power again, continue to hold the RE SET button for about five seconds to reset the Wireless Cable/DSL Router to the factory default settings.
5 4 3. Connect the power supply T urn on your cable or DSL modem. Connect the included power cord to the power jack on the Wireless Cable/DSL Router . Plug the power cord into a standard power outlet. T urn on your PC. Congratulations! The installation procedure is now complete.
7 6 3. Connect the power supply T urn on your analog or ISDN modem. Connect the included power cord to the power jack on the Wireless Cable/DSL Router . Plug the power cord into a standard power outlet. 4. Select the connection method Launch a Web browser .
9 8 Click Next to launch the Add Printer Wizard . When prompted to choose how your printer is attached to your computer , select Local Printer . Select USRPRTSHR for the printer port and click Next . You will then need to supply Windows with the correct printer drivers provided by the printer’ s manufacturer .
11 10 I do not know if my assigned IP Address is Static or Dynamic. Possible Solution: If you have cable or DSL ser vice, you most likely have a Dynamic I P address. Y ou should always check with your service provider to verify this information, since some providers will assign Static IP addresses.
13 12 Are Y ou Still Having Problems? 1. Go to the Suppor t section of the U.S. Robotics Web site at www.usr .com . Many of the most common difficulties users experience have been addressed in the FAQ and T roubleshooting Web pages for your specific product.
15 14 Appendix A This guide covers most cable and DSL installations that are configured for Dynamic or Static I P addressing. This guide assumes that you have active and properly functioning cable or DSL Internet service.
17 16 Note: If you collected any network information, you will need to enter this information into the WAN configuration screens of the Primary Setup section of the Configuration Utility . Note: Write down the settings for your Wireless Cable/DSL Router for future reference.
19 18 In the location or address line of your Web browser , type http://192.168.123.254 to access the Configuration Utility . The Web-based Configuration Utility is where you can go to make any changes to the settings of the Wireless Cable/DSL Router .
20 U.S. Robotics shall not be responsible for any software, firmware, information, or memory data of Customer contained in, stored on, or integrated with any products returned to U.S. Robotics for repair , whether under warranty or not. WARRANTI ES E XCL USIVE: IF A U.
21 Printed in T aiwan.
An important point after buying a device US Robotics Wireless Cable/DSL Router (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought US Robotics Wireless Cable/DSL Router yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data US Robotics Wireless Cable/DSL Router - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, US Robotics Wireless Cable/DSL Router you will learn all the available features of the product, as well as information on its operation. The information that you get US Robotics Wireless Cable/DSL Router will certainly help you make a decision on the purchase.
If you already are a holder of US Robotics Wireless Cable/DSL Router, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime US Robotics Wireless Cable/DSL Router.
However, one of the most important roles played by the user manual is to help in solving problems with US Robotics Wireless Cable/DSL Router. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device US Robotics Wireless Cable/DSL Router along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
