Instruction/ maintenance manual of the product Storm 9528 Troy-Bilt
Go to page of 28
m _ _ _ ,_m_ r Operator's Manual Two-Stage Snow Thrower 8526--Storm 9528--Storm J IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY WARNING: This unit is equipped with an internal combustio.
Content Important Safe Operation Practices Assembling Your Snow Thrower Know Your Snow Thrower Operating Your Snow Thrower Making Adjustments TABLE OF CONTENTS Page 3 6 8 10 13 Content Page Maintainin.
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. DANGER: This machine was built to be operated according to the rules for safe operation in this manual.
Operation 1. Do not puthands or feetnear rotating parts, in the auger/impeller housing or chute assembly. Contact with the rotating parts can amputate hands and feet. 2. The auger/impeller control lever is a safety device. Never bypass its operation. Doing so makes the machine unsafe and may cause personal injury.
YOUR RESPONSIBILITY Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine. Do not modify engine To avoid serious injury or death, do not modify engine in any way.
SECTION 2: ASSEMBLING YOUR SNOW THROWER NOTE: References to right or left side of the snow thrower are determined from behind the unit in the operating position (standing directly behind the snow thrower, facing the handle panel). IMPORTANT: Two replacement auger shear pins are included with this manual (or stowed in the plastic handle panel).
NOTE: If the flange keepers will not easily click into place, use the palm of your hand to apply swift, firm pressure to the back of each. 5. Remove the clevis pin and hairpin clip from the upper portion of the chute mast. • Position the control head over the chute mast and rear portion of the chute assembly.
SECTION 3: KNOW YOUR SNOW THROWER Drive Control Electric Starter Button Gas Cap Oil Fill Chute Assembly Clean-out_ Tool Shift Lever Chute Directional Control / Auger Control f Engine Controls Electric.
Auger Control f The auger control is located on the left handle. Squeeze the control grip against the handle to engage the augers and start snow throwing action. Release to stop. Drive Control The drive control is located on the right handle. Squeeze the control grip against the handle to engage the wheel drive.
SECTION 4: OPERATING YOUR SNOW THROWER Before Starting ,_ WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating. Gas & Oil Fill-Up Service the engine with gasoline and oil as instructed in the Tecumseh Engines manual packed separately with your snow thrower.
• Pull the starter handle with a firm, rapid stroke. IMPORTANT: Do not release the handle and allow it to snap back. Keep a firm hold on the starter handle and allow it to slowly recoil. • As the engine warms, slowly rotate the choke control to the OFF position.
• Retighten the hex jam nut. See Figure 1. • Repeat Auger Control Test to verify proper adjustment has been achieved. ii ', Figure 1 Chute Clean-Out Tool The chute clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip.
SECTION 5: MAKING ADJUSTMENTS _, WARNING: Never attempt to make any adjustments while the engine is running, except where specified in operator's manual. ShiftRod Adjustment If the full range of speeds (forward and reverse) cannot be achieved, refer to the figures to the right and adjust the shift rod as follows: 1.
Drive Control When the drive control is released and in the disengaged "up" position, the cable should have very little slack. It should NOT be tight. Check the adjustment of the drive control as follows: 1. With the drive control released, push the snow thrower gently forward.
SECTION 6: MAINTAINING AND SERVICING YOUR SNOW THROWER WARNING: Before lubricating, repairing, or inspecting, disengage all controls and stop engine. Wait until all moving parts have come to a complete stop. Engine Refer to the separate Tecumseh Engines manual packed with your unit for all engine maintenance.
i ' /' / ....... / / i is .......... i i' Auger BeltReplacement To remove and replace your snow thrower's auger belt, proceed as follows: 1. Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws.
/ 7 / i DriveBelt Replacement To remove and replace your snow thrower's auger belt, proceed as follows: 1. Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws. • Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap.
Friction WheelRemoval If the snow thrower fails to drive with the drive control engaged, and performing the drive control cable adjustment on page 14 fails to correct the problem, the friction wheel may need to be replaced. Follow the instructions below.
Augers • The augers are secured to the spiral shaft with two shear pins and cotter pins. If the auger should strike a foreign object or ice jam, the snow thrower is designed so that the pins may shear. Refer to Figure 6. • If the augers will not turn, check to see if the pins have sheared.
SECTION 8: TROUBLE SHOOTING GUIDE Trouble Possible Cause(s) Engine fails to start Fuel tank empty, or stale fuel. Blocked fuel line. Choke control not in ON position Faulty spark plug. Ignition key not present. Spark plug wire disconnected. Engine not primed.
NOTES 21.
SECTION 9: PARTS LIST 15 4O 16 25 5 30 21 10 19 18 22 13 2O 36 47 17 12 29 39 "15 / 22.
Style Q REF. PART NO. NO. 1 631-04127 2 631-04133 3 631-04134 4 684-04105 5 684-04106 6 710-04326 7 710-04354 8 710-1026 9 710-1233 10 711-04287 11 711-0677 12 712-04064 13 712-04081A 14 714-0104 15 7.
Style Q 18 7O 7 38 26 7 _17 3 22 41 34 j 30 32 56 2 49 68 _2_ 62 5458 _ 61 4 64 65 8 6 e 35 7 24.
Style Q REE PART NO. NO. 1 731-2643 2 684-04057 3 710-0347 4 710-0451 5 710-0703 6 710-0726 7 712-04063 8 712-04064 9 712-04065 10 714-0507 11 725-0157 12 726-04012 13 731-04705 14 732-0611 15 736-017.
Style Q 13 4O 58 53 57 47 7 20 24 ¢_/,/ 30 36 56 24 50 7 48 14 4 41 60 49 55 52 21 58 27 62 26 61 / 32 38 25 67 66 26.
Style O RER PART NO. NO. 1 517-04026 2 517-04025 3 B56-0012A 4 584-04066 5 584-04045 6 584-04139 7 710-0627 8 710-0788 90 710-1652 711-04246A 11 712-0711 12 714-0161 13 716-0231 14 716-0136 15 717-041.
MANUFACTURER'S LIMITED WARRANTY FOR: ® m The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used in the United States and/or its territo.
An important point after buying a device Troy-Bilt Storm 9528 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Troy-Bilt Storm 9528 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Troy-Bilt Storm 9528 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Troy-Bilt Storm 9528 you will learn all the available features of the product, as well as information on its operation. The information that you get Troy-Bilt Storm 9528 will certainly help you make a decision on the purchase.
If you already are a holder of Troy-Bilt Storm 9528, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Troy-Bilt Storm 9528.
However, one of the most important roles played by the user manual is to help in solving problems with Troy-Bilt Storm 9528. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Troy-Bilt Storm 9528 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
