Instruction/ maintenance manual of the product Welding System Tripp Lite
Go to page of 8
Saf ety 2 F eature Identification 3 Operation 4 Application Guide 5 Mounting 6 Batter y Connection 7 A C Output Connection 8 (back page) T roubleshooting/Service/ Maintenance/W arranty 8 (back page) W arranty Registr ation 8 (back page) Owner’ s Man ual P o werV er ter ® Plus DC-to-A C In ver ters Input Output 12 VDC 120V , 60 Hz.
Impor tant Safety Instructions SA VE THESE INSTR UCTIONS! This manual contains important instructions and warnings that should be followed during the installation, operation and storage of all T ripp Lite Inverters.
3PV Feature Identification Identify the premium features on your specific model and quickly locate instructions on how to maximize their use. Operating Mode Switch: controls Inverter operation.
4PV Operation Switch Modes Switch between the following operating modes as appropriate to your situation: “ON/REMOTE”: Switch to this setting to pro- vide connected equipment with AC power . Also, switch to this setting to remotely monitor and control the Inverter with the use of an optional remote module.
5PV Application Guide 540 watts ÷ 12V = 45 DC Amps 45 DC Amps × 5 Hrs. Runtime × 1.2 = 270 Amp-Hours Match Battery Amp-Hour Capacity to Y our Application Select a battery or system of batteries that will provide your Inverter with proper DC voltage and an adequate amp-hour capacity to power your application.
V ehicular and Non-V ehicular Horizontal Mount Using the measurements from the diagram, install two user-sup- plied ¼" ( 6 mm) fasteners into a rigid horizontal surface, leaving the heads slightly raised. Slide the Inverter/Charger back over the fasteners to engage the mounting slots molded on the bottom of th e Inverter/Charger cabinet.
7PV • Connect DC W iring: Y ou must run positive cable(s) through user-sup- plied UL-listed fuse(s) and fuse block(s) of the proper size. See Specifications page for Minimum Recommended Cable Sizing Chart. An excellent sour ce of cables is battery jumper cables.
8PV T ry these remedies for common Inverter problems before calling for assistance. Call T ripp Lite Customer Service at (773) 869-12 34 before returning your unit for service. T r oubleshooting SYMPT OM PROBLEMS CORRECTIONS No AC Output Operating Mode Switch is set to “OFF .
An important point after buying a device Tripp Lite Welding System (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Tripp Lite Welding System yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Tripp Lite Welding System - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Tripp Lite Welding System you will learn all the available features of the product, as well as information on its operation. The information that you get Tripp Lite Welding System will certainly help you make a decision on the purchase.
If you already are a holder of Tripp Lite Welding System, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Tripp Lite Welding System.
However, one of the most important roles played by the user manual is to help in solving problems with Tripp Lite Welding System. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Tripp Lite Welding System along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
