Instruction/ maintenance manual of the product 2200XLT Tripp Lite
Go to page of 8
1 Copyright © 1999 Tripp Lite. All rights reserved. SmartPro ® is a registered trademark of Tripp Lite. Installation: p. 3 - 4 Basic Operation: p. 4 - 6 Storage & Service: p. 7 Specifications: p. 7 Safety: p. 2 W arranty & Insurance: p. 6 1111 W.
2 This manual contains important instructions and warnings that should be followed during the installation, operation and storage of all Tripp Lite UPS Systems. UPS Location W arnings • Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight.
3 Installation Plug y our UPS into an electrical outlet. The SmartPro 2200XLT should be connected to a 15-amp dedicated circuit. Plug y our equipment into y our UPS. T urn y our UPS ON. Set the System Enable Switch (DIP Switch #4, UPS back panel) to the “ENABLE” (UP) position.
4 Switches System Enable Switch (DIP Switch #4) This switch is located in the set of 4 switches next to the UPS’s DB9 ports. It activates the battery charger and intelligent microproces- sor. Always leave it in the “ENABLE” (UP) position when your UPS is plugged in.
5 ON/Standby Switch This momentary switch controls power to the UPS receptacles. Engage it momentarily and release it to toggle between the “ON” mode (power ON at the UPS receptacles) and “Standby” mode (power OFF at the UPS receptacles).
6 This multi-colored light displays 4 separate UPS load conditions. It will turn from green (low) to yellow (medium) to red (high) as you connect equipment to show you the load level your UPS is support- ing. When the light is red your UPS is supporting a load above 85% of its capacity.
7 Specifications Storage & Service Storage Turn your UPS OFF: first engage the ON/Standby Switch and release it to place your UPS in the “Standby” mode; then set the System Enable Switch (Jumper #4, UPS rear panel) to "DISABLE" (down); finally, disconnect the UPS power cord from the wall outlet.
8 93-1503 (9911081) 1111 W. 35th Street Chicago, IL 60609 USA Customer Support: (773) 869-1234 www.tripplite.com 9911081 230V Smartpro 2200T OM.p65 11/24/99, 12:00 PM 8.
An important point after buying a device Tripp Lite 2200XLT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Tripp Lite 2200XLT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Tripp Lite 2200XLT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Tripp Lite 2200XLT you will learn all the available features of the product, as well as information on its operation. The information that you get Tripp Lite 2200XLT will certainly help you make a decision on the purchase.
If you already are a holder of Tripp Lite 2200XLT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Tripp Lite 2200XLT.
However, one of the most important roles played by the user manual is to help in solving problems with Tripp Lite 2200XLT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Tripp Lite 2200XLT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
