Instruction/ maintenance manual of the product B-8204-QM-R Toshiba
Go to page of 22
- 1 - Rotary Cutter Module B-8204-QM-R Installation Manual 1. APPLICABLE MODEL This optional kit is the rotary cutter module, which is intended for the following models: B-SX4T Series, B-SX5T Series NOTE: When using the Rotary Cutter to the B-SX4T Series, be sure to install the Ribbon Saving Module (B-9904-R/R2-QM).
- 2 - 3) Remove the four B-4x5 screws from the side panel (L). 4) Open the top cover and remove the three P- 4x8 screws that secure the side panel (L). 5) Lift the side panel (L) and put it aside. 6) Disconnect the fan motor harness from CN19 on the Main PC board, and then separate the side panel (L).
- 3 - 8) Connect the 9-pin connector of the harness ass’y to CN7 and 2-pin connector to CN9 on the cutter driver unit, respectively. 9) Fit the bush to the harness ass’y in the orientation as shown below. 10) Insert the harness ass’y into the hole in the main frame.
- 4 - 11) Fix the harness ass’y with the clamp. 12) Connect the 9-pin connector of the harness ass’y to CN15, and 2-pin connector to CN18 on the Main PC board, respectively. 13) Turn the head lever counterclockwise to Free position. 14) Open the ribbon shaft holder plate.
- 5 - 16) Connect the four harnesses of the cutter unit to CN8, CN10, CN11 and CN12 on the cutter drive unit. 17) Fit the two tabs of the cutter drive unit into the notches, and then fix the cutter unit with the three SM-4x8 screws.
- 6 - 18) Attach the cutter cover to the cutter unit with the two screws so that the tab of the cutter cover turns on the cutter cover open switch. NOTES: 1. Be careful not to pinch the cutter harness by the cutter cover. 2. Make sure that the anti-static brush is protruding from the media outlet.
- 7 - 3.2 Installing the Rotary Cutter Unit on the B-SX5T Series Since the strip module is st andard on the B-SX5T series, it is necessary to remove the rewinder guide plate, strip sensor, etc. before in stalling the cutter module. 1) Turn the power off and disconnect the power cord.
- 8 - 5) Lift the side panel (L) and put it aside. 6) Disconnect the fan motor harness from CN19 on the Main PC board, and then separate the side panel (L). 7) Remove the SM-4x8 screw that secures the operation panel ass’y. 8) Half open the top cover, otherwise the operation panel ass’y cannot be removed from the printer.
- 9 - 10) Disconnect the operation panel harness from the operation panel ass’y. 11) Turn the head lever clockwise to Free position. 12) Open the ribbon shaft holder plate.
- 10 - 13) Raise the print head block until it stops. 14) Remove the two SMW-4x8 screws that se cure the strip sensors (TR) and (LED). 15) Release the strip sensor (LED) har ness from the cable clamp, and disc onnect it from the shorter harness of the strip sensor harness (TR).
- 11 - 16) Remove the Expansion I/O board from the prin ter temporarily using the following procedure. (1) Disconnect the Expansion I/O cable from CN1 on the Expansion I/O board. (2) Remove the two B-3x6 screws to detach the Expansion I/O board from the printer.
- 12 - 20) Fix the cutter drive unit to the printer with the three SM-4x8 screws. 21) Connect the 9-pin connector of the harness ass’y to CN7 and 2-pin connector to CN9 on the cutter driver unit, respectively. 22) Fit the bush to the harness ass’y in the orientation as shown below.
- 13 - 24) Fix the harness ass’y with the clamp. 25) Connect the 9-pin connector of the harness ass’y to CN15, and 2-pin connector to CN18 on the Main PC board, respectively. 26) Connect the four harnesses of the cutter unit to CN8, CN10, CN11 and CN12 on the cutter drive unit.
- 14 - 27) Fit the two tabs of the cutter drive unit into the notches, and then fix the cutter unit with the three SM-4x8 screws. 28) Attach the cutter cover to the cutter unit with the two screws so that the tab of the cutter cover turns on the cutter cover open switch.
-15 - ロータリーカッターモジュール(B-8204-QM-R) 組込説明書 このたびは「ロータリーカッターモジュール B-8204-QM-R」をお買い上げいただき、誠にあり.
-16 - ■ 組込手順 1) プリンタの電源スイッチを OFF にし、電源プラグをコンセ ントから抜きます 。 2) 用紙発行口下側の黒い化粧ネジ２本を外し、目.
-17 - 7) ヘッドレバーを Free の位置まで回します。 8) リボンシャフト固定板を静か に右側へ倒します。 9) 印字ヘッド機構部を持ち上げてロ ックしま.
-18 - 11) カッターケーブルをカッター制御部の CN7 と CN9 へ接続します。 12) カッターケーブルにコードブッシュを取り 付けます。 13) カッターケーブ.
-19 - 14) コードクランプでカッターケーブルを止め、Main PC 板の CN15 と CN18 へカッターケーブル を接続します。 15) カッター機構部の４本のコネクタ.
-20 - 16) カッター制御部の２つの突起部とカッ ター機構部の角穴を合わせ、セム スネジ(SM-4x8)３ 本でカッター 機構部を固定します。 補足 ケー ブル.
-21 - 18) 印字ヘッド機構部のロック を解除して静かに下ろ し、リボンシ ャフト固定板を閉め ます。 19) 冷却 ファンケーブルを接続し、左サイドカバ.
FMMB0067606 Printed in Japan EO2-38009F Ⓒ東芝テック株式会社 2008.
An important point after buying a device Toshiba B-8204-QM-R (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toshiba B-8204-QM-R yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toshiba B-8204-QM-R - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toshiba B-8204-QM-R you will learn all the available features of the product, as well as information on its operation. The information that you get Toshiba B-8204-QM-R will certainly help you make a decision on the purchase.
If you already are a holder of Toshiba B-8204-QM-R, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toshiba B-8204-QM-R.
However, one of the most important roles played by the user manual is to help in solving problems with Toshiba B-8204-QM-R. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toshiba B-8204-QM-R along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
