Instruction/ maintenance manual of the product 4200FA Toshiba
Go to page of 10
4200 FA -XT 1 TOSHIBA International Corp GUIDE SPECIFICATIONS THREE PHASE UNINTERRUPTIBLE POWER SYSTEM TOSHIBA 4200 FA 15 / 25 / 30 / 50 kVA UPS GUIDE SPECIFICATIONS.
4200 FA -XT 2 (15 / 25 / 30 / 50 kVA) 1.0 SCOPE 1.1 System This specification describes a conti nuous duty, three-phase, on-line, solid- state uninterruptible power supply system, hereafter referred to as the UPS.
4200 FA -XT 3 H. Input / Output EMI / RFI Filters 2.3 System Operation The UPS shall operate as an on-line, fully automatic system in the following modes: A.
4200 FA -XT 4 protection against spikes, common/normal mode noise, load steps and frequency shifts (without battery back-up capability). 3.0 SYSTEM PARAMETERS A.
4200 FA -XT 5 +/- 3% (loss or return of input power) +/- 8% (bypass to inverter) 13) Transient Voltage Recovery 50ms maximum to within 2% of nominal 14) Overload Cap. (on inverter) 125% for 90 sec., 150% for 30 sec. 15) Overload Cap. (on bypass) 1000% for 10ms, 125% for 10 min.
4200 FA -XT 6 6) Altitude: 3300 ft. maximum without derating (up to 5000 ft.- 95% capacity; up to 7500 ft. - 90% capacity) 4.0 FUNCTIONAL DESCRIPTION A.
4200 FA -XT 7 steady voltage waveform. The invert er switching speed shall be fast enough to limit audible noise to 60 dBA at 3 feet (measured on ‘A’ scale).
4200 FA -XT 8 discharging: flickers when t he battery voltage is below minimum. d) BYPASS (Green Lamp) - Lights when in circuit-bypass mode. d) FAULT (Red Lamp) - Lights when a fault has been detected.
4200 FA -XT 9 UPS Size Dimensions W e i g h t 15 kVA 20”W x 36.3”D x 59.8”H 794-998 lbs. 25 kVA 20”W x 36.3.”D x 59.8”H 804-1,003 lbs. 30 kVA 20”W x 36.3”D x 59.8”H 809-1,008 lbs. 50 kVA 35.25”W x 37.6”D x 59. 8”H 1,221-1,946 lbs.
4200 FA -XT 10 The following normally open dry contac ts shall be provided through a DB9 male connector located on the rear of the UPS enclosure: 1) UPS On 2) Bypass Active 3) Input Power Loss 4) Battery Voltage Low D.
An important point after buying a device Toshiba 4200FA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toshiba 4200FA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toshiba 4200FA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toshiba 4200FA you will learn all the available features of the product, as well as information on its operation. The information that you get Toshiba 4200FA will certainly help you make a decision on the purchase.
If you already are a holder of Toshiba 4200FA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toshiba 4200FA.
However, one of the most important roles played by the user manual is to help in solving problems with Toshiba 4200FA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toshiba 4200FA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
