Instruction/ maintenance manual of the product 24 VDC Beckett
Go to page of 16
Potential for Fire, Smoke and Asphyxiation Hazards T o the Homeowner or Equipment Owner: Please read and carefully follow all instructions provided in this manual regarding your responsibilities in caring for your heating equipment. Contact a professional, quali fi ed service agency for installation, start-up or service work.
2 Contents Burner Application Scope and Intended Use ........... 2 Prepare Before Installing ............................................ 3 Notice Special Requirements............................................. 3 Speci fi cations ..................
3 24 Vdc SDC Burner Manual Notice Special Requirements If you discover damage to the burner or controls during unpacking, notify the carrier at once and fi le the appropriate claim. When contacting Beckett for service information — Please record the burner serial number (and have available when calling or writing).
4 T able 1. Combustion Head Firing Rates Firing Rate GPH (min - max) Head 1.75 - 3.25 F22/F220 2.50 - 5.50 F310 Section: General Information & Nozzle Assembly Maintenance Adequate V oltage Require.
5 24 Vdc SDC Burner Manual Section: Nozzle Assembly Maintenance Correct Nozzle and Flow Rate Required Incorrect nozzles and fl ow rates could result in impaired combustion, under- fi ring, over- fi ring, sooting, puff-back of hot gases, smoke and potential fi re or asphyxiation hazards.
6 Figure 5. ‘Z’ Dimensions Using Gauge SK9787 Section: Nozzle Assembly Maintenance The Beckett Z gauge (part number Z- 2000) is available to permit checking the F head “Z” dimension without removing the burner .
7 24 Vdc SDC Burner Manual A. Connect Fuel Lines For oil supply system speci fi cations for tanks not mounted on machines, carefully follow the pump manufacturer ’s literature and the latest edition of the National Fire Protection Association (NFP A) 31 standard.
8 Section: Burner Wiring Explosion, Fire, Scald, & Burn Hazard All heating equipment must have HIGH LIMIT controls to protect against excessive temperature and/or pressure. The control must interrupt electrical power and shutdown the burner , if operating or safety controls fail and cause a runaway condition.
9 24 Vdc SDC Burner Manual Section: Drive Component Maintenance Driv e Component Maintenance A. Motor , Blower Wheel, & Coupling Replacement The motor will require replacement if the proper voltage is measured at the motor input, and the motor will either not run, or the current draw with a free running pump exceeds 10% of the rated current.
10 Explosion and Fire Hazard Failure to follow these instructions could lead to equipment malfunction and result in heavy smoke emission, soot-up, hot gas puff-back, fi re and asphyxiation hazards.
11 24 Vdc SDC Burner Manual Section: Maintain & Service Burner Maintain & Ser vice Bur ner A. Owner ’ s Information Have your equipment inspected at regular intervals by a quali fi ed service agency to assure continued proper operation. The burner should be adjusted using dedicated combustion test equipment.
12 T roubleshooting Oil burners that are designed for use on road maintenance equipment are built to take temperature extremes, vibration, and rough handling.
13 24 Vdc SDC Burner Manual Section: T roubleshooting T able 3. Troubleshooting Chart Symptom Possible Cause Oil Not Igniting If the burner is not igniting, the burner motor , drive coupling, and oil pump are operating and oil is fl owing to the nozzle through the solenoid valve, check the following possibilities.
14 R eplacement P ar ts Section: Replacement Parts 21 20 14 15 19 17 16 13 12 10 9 8 4 5 6 7 3 2 1 22 18 11 * ‘ X ’s indicate timing options. Contact Beckett for available part numbers.
15 24 Vdc SDC Burner Manual.
The R. W . BECKETT CORPORA TION (“Beckett”) warrants to persons who purchase its “Products” from Beckett for resale, or for incorporation into a product for resale (“Customers”), that its equipment is free from defects in material and workmanship.
An important point after buying a device Beckett 24 VDC (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Beckett 24 VDC yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Beckett 24 VDC - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Beckett 24 VDC you will learn all the available features of the product, as well as information on its operation. The information that you get Beckett 24 VDC will certainly help you make a decision on the purchase.
If you already are a holder of Beckett 24 VDC, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Beckett 24 VDC.
However, one of the most important roles played by the user manual is to help in solving problems with Beckett 24 VDC. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Beckett 24 VDC along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center