Instruction/ maintenance manual of the product 15RTV TOA Electronics
Go to page of 20
15-INCH TFT-LCD MONITOR 15 RTV INSTRUCTION MANUAL Please read this manual thoro ughly before us e, and ke ep it handy for future reference..
SAFETY INSTRUCTION……………………………… …………………………………….2 - 3 CAUTIONS ……………………………… ………..…… ……………… ………… …… ………..4 FCC RF INTERFERENCE STATEMENT …… …… ………………………………………….
1. Read all of these instructions. 2. Save these instructions for later use. 3. Follow all warnings and instruction s marked on the product. 4. Unplug this product from the wall outlet before cle aning. Do not use liquid cleaners or aerosol cleaners. Use a damp cl oth for cleaning.
Refer all servicing to service personnel. 14. Unplug this product from the wall ou tlet and refer servicing to qualified service personnel under the following conditions. A. When the power cord or plug is damaged or frayed. B. If liquid has been spilled into the product.
▶ NEVER REMOVE THE BACK COV ER Removal of the back cover should be carried out only by qualified personnel. ▶ DO NOT USE IN HOSTILE ENVIRONMENTS To prevent shock or fire hazard, do not expose the unit to rain or moisture. This unit is designed to be used in the office or home.
NOTE This equipment has be en tested a nd found to comply with the lim its for a Cla ss B digital device, pursuant to Part 15 of the FCC Rules. T hese limits are desi gne d to provide reasonabl e protection against harmful interference i n a residential installation.
A. BOTTOM PANEL CONTROL 1. DC 12V IN 2. D-SUB IN PC Signal Input 3. VIDEO 1(AV1) IN Composite signal Input for AV1 4. VIDEO 1(AV1) OUT Video looping output for AV1 5. VIDEO 2(AV2) IN Composite signal Input for AV2 6. VIDEO 2(AV2) OUT Video looping output for AV2 7.
B. REMOTE CONTROLLER 1. POWER( ) Turns the power ON or O FF. There will be a few seconds delay before the d isplay appears. 2. SOURCE Select pc or video( PC / AV1 / AV2 / S-Video ) sources. 3. MUTE Mute the sound. 4. MENU Activates and exits the On Screen Displ ay.
1. SOURCE Select input source, and move the previous menu. 2. MENU Activates and exits the On Scre en Display . This button can also be used to move previous menu or status. OSD MENU(MAIN) : Input Source, Screen, Audio, OSD, Color , Utility , Exit. 3/4.
1. SELF-TEST DISPLAY When there is no connection at PC, the On Screen Display will show for 3 seconds. 2. OSD MENU DESCRIPTION : Input Source Select PC or AV1, SVIDEO.
: Screen : Brightness Increase or decrease the intensity of the image. : Contrast Increase or decrease the intensity (lightness or di mness) of the image. : H. position (PC Mode Only) Move image horizontally on screen right or left. : V. position (PC Mode Only) Move image vertically on screen up or down.
: Audio : Volume Adjust audio volume. 11 ………………………………… ………………………………………… INSTRUCTION MANUAL.
: OSD : H. Position Move the OSD position to right( ▶ ) or left( ◀ ). : V. Position Move the OSD position to up( ▶ ) or down( ◀ ). : Transparency Select the OSD backgrou nd. : OSD Tim er Select the OSD display timing. : Language Select a language among English, Françai s, Deutsch, Español, Danish, Italiano.
: Color (PC Mode) : Color Temp Adjust color temperature to 9300, 6500, user. (note : 9300 is factory default) : Red Adjust red color for user. : Green Adjust green color for user.
: Utility : Recall Select to reset all setting to the factory default values. : Lock Select ON or OFF (ON : Control key lock. OFF : Control key unlock) : Exit : Exit Turn off OSD Menu. INSTRUCTION MANUAL ……………………………………… …………………………………… 14 H :15.
Wall - mount installation : 1) Remove the pedestal mount installed on the monitor. 2) Us e the VESA standard mount ing design and the 100mm h ole pattern on the back panel to install the LCD monit or to the (optional) mounting bracket sold separately .
▶ PIN ASSIGNME NTS ▶ ACCESSORY 1. POWER CORD 2. USER’S MANUAL 3. PC cable 4. Adaptor 5. Remote Control 6. Batteries 7. Wall mount (Option) INSTRUCTION MANUAL ……………………………….
This monitor features a po wer management sy stem to “power d own” upon receipt of the VESA DPMS(The display power management si gnaling) from a VESA DPMS video card. The VESA DPMS-compliant video card performs th is signaling system through not sending horizontal, vertical, or sync signal.
▶ LCD T ype 15˝ Diagonal AM-TFT(Active-Matrix) Pixel pitch (mm) : 0.297(H) 0.297(V) BRIGHTNESS: 250cd/ ㎡ (Typical) CONTRAST RATIO: 450:1(Typical) RESPONSE TIME: 12msec (Typical) ▶ RESOLUTION(H x V) 1024X768 @ 60Hz ▶ FREQUENCY HORIZONTAL : 30KHz - 4 8KHz VERTICAL : 56Hz - 75Hz ▶ INPUT SIGNAL RGB (Analog 0.
WEEE Symbols 19 ………………………………… ………………………………………… INSTRUCTION MANUAL “ Going to Sleep” message on screen Correct Disposal of This Product (Wa.
An important point after buying a device TOA Electronics 15RTV (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought TOA Electronics 15RTV yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data TOA Electronics 15RTV - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, TOA Electronics 15RTV you will learn all the available features of the product, as well as information on its operation. The information that you get TOA Electronics 15RTV will certainly help you make a decision on the purchase.
If you already are a holder of TOA Electronics 15RTV, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime TOA Electronics 15RTV.
However, one of the most important roles played by the user manual is to help in solving problems with TOA Electronics 15RTV. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device TOA Electronics 15RTV along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
