Instruction/ maintenance manual of the product SIP LD4105S Teledex
Go to page of 10
SIP LD4100/4200 Series User Guide WHEN USING YOUR TELEPHONE EQUIPMENT , BASIC SAFETY PRECAUTIONS SHOULD AL WA YS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSONS, INCLUDING THE FOLLOWING: 1. READ AND UNDERST AND ALL INSTRUCTIONS.
1. Introduction to the T eledex iPhone SIP LD Series IP Phone 3 1.1 Definitions, acronyms and abbreviations 3 1.2 The SIP LD Series works like a telephone 3 1.3 T wo lines 3 1.4 The network 3 1.5 The IP-PBX 3 1.6 The network system administrator 3 2.
1. Introduction to the T eledex iPhone SIP LD Series IP Phone The T ele dex iP hone SI P LD s eries I P phon e is a SIP-co mpliant network terminal. Instead of using standard analog or digital telephone lines, it connects to the network in the same manner as computers and printers do.
2.4 Connecting the Handset Plug one end of the coil cord into the RJ-10 receptacle on the handset, and the other end into the receptacle on the left side of the base.
Figure 2 shows the welcome page of the configuration portal. The phone can be configured through the main menu provided by this portal. NOTE: Except for upgrading the software online (decribed in subsection 3.2.7), the configuration for the SIP LD series will not be activated until the phone has been reset.
3.2.5 Configure the Call Featur es (Fig. 6) The configurable call features include Do Not Disturb, Call T ransfer , Call Forward No Answer , Call Forward Busy , Call Waiting, and Call Forward All. A call forward extension number can be pre-configured.
Fig 9: Reset the Phone 3.2.9 Restore to Factory Configuration T o restore the phone to the factory (default) configuration via the configuration portal, follow these steps: 1. Click “Restore to Factory” on the left menu. 2. Click “Restore” to restore factory settings.
4.7 TRANSFERRING A CALL Note: This feature will not be valid unless it is enabled. The ND2210S can transfer an ongoing call to another phone on the same network if this feature is enabled through web portal configuration. T o transfer a call: 1. Press the FLASH key; this will place the call on hold and activate the second line.
5.4 Three-W ay Conference Calls The SIP LD series supports three-way conference calling. The CONF or FLASH key allows the user to include two other parties in a three-way conversation. One three-way conference could be done using only one line or both lines.
Power Power supplied from network switch (PoE), or from approved local power adapter Dimensions & Weight W : 9.0” (22.86 cm) D: 8.5” (21.59 cm) H: 6.47” (16.43 cm) full upright position 3.97” (10.08 cm) full flat position Wt: 2.80 lb. (1.
An important point after buying a device Teledex SIP LD4105S (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Teledex SIP LD4105S yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Teledex SIP LD4105S - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Teledex SIP LD4105S you will learn all the available features of the product, as well as information on its operation. The information that you get Teledex SIP LD4105S will certainly help you make a decision on the purchase.
If you already are a holder of Teledex SIP LD4105S, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Teledex SIP LD4105S.
However, one of the most important roles played by the user manual is to help in solving problems with Teledex SIP LD4105S. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Teledex SIP LD4105S along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
