Instruction/ maintenance manual of the product B72BL Baumatic
Go to page of 28
1 B72BL 60 cm 4 burner glass gas hob B77BL 70 cm 5 burner glass gas hob B78BL 70 cm 5 burner gas glass hob with thermoc ouples..
User Manual for your Baumatic B72BL 60 cm 4 burner gas glass hob B77BL 5 burner gas glass hob B78BL 5 burner gas glass hob with thermocouples NOTE : This User Instruction Manual contains imp ortant information, including safety & installation p oints, which will enable you to get the most out of your appliance.
3 Contents E n v i r o n m e n t a l n o t e 4 Important safety informa tion 5 – 7 Specifications 8 Product & aperture dimensions (B72BL) 8 Product specifications (B72BL) 8 Standard accessories .
Environmental note 4 o Baum atic uses are environmentally friendly and can be recycled. o all packaging mate rial with due regard for the environment. The packaging materials that Please discard.
5 Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If yo are unsure of any of the info rmation contained i booklet, pleas u n this e contact the Baumatic Technical ent.
6 hild Safety o d ny time. During and after use, all surfaces will become hot. o se ensure that they are kept under close supervision at all times. o ld only be allowed to utilise the appliance when supervised.
o Great care should be taken whils t using this appliance and when following the cleaning procedure. o You should not use a steam jet or any other high pressure cleaning equipment to clean the appliance.
Specifications B72BL Product dimensions: Aperture dimensions: Height: 510 mm Height: 490 mm Width: 580 mm Width: 560 mm Depth: 50 mm Product specifications: o 1 x 3.
B77BL & B78BL Product dimensions: Aperture dimensions: Height: 510 mm Height: 510 mm Width: 680 mm Width: 562 mm Depth: 50 mm Product specifications: o 1 x 3.50 kW triple crown (wok) burner o 1 x 3.00 kW rapid-burner o 2 x 1.75 kW semi-rapid burners o 1 x 1.
Electrical details Rated Voltage: 230 Vac 50 Hz Supply Connection: 3 A (double pole switched fused outlet with 3mm contact gap) Max Rated Inputs: 0.008 to 0.02 kW (depending on model) Mains Supply Lead: 3 core x 0.75mm² (Type RR-F <HAR> marked) Gas details Connection: Rp ½ (ISO R7) Type: Natural Gas (20.
B77BL/B78BL Using the gas hob Before first use IMPORTANT: You should clean the hob surface (see “Cleaning and maintenance” section). Turning the hob on The following symbols will appear on the con.
12 Automatic electric ignition To ignite a burner: o Press in the control knob of the bu rner that you wish to light and turn it anti-clockwise to the maximum position. o If you keep the control knob depressed, the automatic ignition for the burner will operate.
Energy saving tips o The diametre of the bottom of th e pan should correspond to that of the burner. o The burner flame must never exte nd beyond the diametre of the pan. o Use flat bottomed pans only o When possible, keep a lid on the pan whilst cooking.
14 tly Although it is easier to cl ean some deposits whilst the hob surface is still warm. Make sure that the hob surface, pan supports and hob burners ha ve all cooled sufficien before you attempt to touch t hem.
Installation The installation must be carried out by a CORGI registered installer, in accordance with the current version of the following. o Gas Safety Regulations (Installation & Use) o Building.
Positioning The adjacent furniture must be able to withstand a minimum temperature rise of 85°C above the ambient temperature of the room it is located in, during periods of use. o This appliance can be located in a kitchen, a kitchen diner or a bed sitting room.
Unpacking the appliance When unpacking the appliance please check that the following items are contained within the packaging: 1 x Baumatic hob 4 x Pan stands (B72BL) 5 x Pan stands 1 x Installation a.
o Cut a hole in the worktop that corresponds with the drawings shown on page 17. o IMPORTANT: You must have a gap of at least 25 mm between the underneath of the appliance an d any surface that is below it. o Carefully turn the hob upside do wn and place it on a cushioned mat.
o Place the clamp (B) over the holes that match the size of the screws. There are one set of screw holes in each corner of the hob. Slightly tighten a screw (C) through the clamp (B) so that the clamp is attached to the hob, but so that you can still adjust the position of it.
20 Ventilation requirements o The room containing the hob sh ould have an air supply in accordance with the current ed ition of BS 5440: Part 2: o The room must have opening windows or equivalent; some rooms may also require a permanent vent. o If the room has a volume between 5 and 10m³, it will require an air vent of 50cm² (effective area).
Gas Safety (Installation and Use) Regulations IMPORTANT: The appliance MUST be connected to the gas supply by use of a ½ BSP Elbo w, seal, copper pipe and an isolation tap fitted in an easily accessible position.
Gas adjustment (Conversion to LPG) All work must be carried out by a CORGI registered engineer. IMPORTANT: Always isolate the cooker from the electricity supply before changing the in jectors and/or adjusting the minimum flow of the burners. o Remove the pan-stands, burners and flame spreaders (A) .
Minimum flow adjustment for hob gas taps. All work must be carried out by a CORGI registered engineer. IMPORTANT: Always isolate the hob from the electricity supply before changing the injectors and/or adjusting the minimum flow of the burners. o Switch the burner on and set the knob at the minimum position.
Gas tap maintenance These maintenance operations MUST ONLY be carried out by a CORGI registered engineer. IMPORTANT: Before carrying out any maintenance operations, disconnect the appliance from th e gas and electricity supplies.
Electrical connection This appliance must be installed by a qualified person in accordance with the latest edition of the I.E.E. Regulations and in compliance with Baumatic’s instructions. Before connecting the appliance, ma ke sure that the supply voltage marked on the rating plate corresponds with your mains supply voltage.
My appliance isn’t working correctly IMPORTANT: If your appliance appears not to be operating correctly, then yo u should disconnect it from your mains supply and then contact the Baumatic Service Department on telephone number (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF.
27 United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Service Telephone (0118) 933 6911 Service Fax (0118) 986 9124 Spares Telephone (01235) 4372 44 Technical Advice Telephone (0118) 933 6933 E-mail: sales@baumatic.
28.
An important point after buying a device Baumatic B72BL (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Baumatic B72BL yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Baumatic B72BL - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Baumatic B72BL you will learn all the available features of the product, as well as information on its operation. The information that you get Baumatic B72BL will certainly help you make a decision on the purchase.
If you already are a holder of Baumatic B72BL, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Baumatic B72BL.
However, one of the most important roles played by the user manual is to help in solving problems with Baumatic B72BL. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Baumatic B72BL along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
