Instruction/ maintenance manual of the product C810 Taylor
Go to page of 50
Models C810 & C812 Auto Lift Grills Operating Instructions 073523-M 9/15/ 10.
Com plete this pa ge for quick r efer ence w hen ser vice is r equir ed: Taylor Distributor: Address: Phone: Serv ice: Par ts: Date of Installation: Infor mati on found on data plate : Model Number: S.
Models C 81 0 & C8 12 Table of Cont ents T able of Contents Section 1 To the Installer 1 ............................................ Installer Safety 1 ........................................................ Site P reparation 1 .................
Table of Cont ents Models C 81 0 & C8 12 Table of Contents - P age 2 Sec tion 5 Im porta nt: To the Oper ator 9 ................................. Section 6 Operating Pr ocedu res 10 ..................................... Daily Openi ng Procedures 10 .
1 Mo del s C810 & C812 To the Insta ller Section 1 To the Installer The f ollowing are general ins tallat ion inst ruct ions. For complet e installat ion det ails, pleas e see t he checko ut card. Installer Safety In all areas of the world, equipment should be installed i n accordanc e with exis ting loc al codes.
2 Mo del s C810 & C812 To the Insta ller CAUTI ON: T HIS EQ UIPM ENT MUST BE PROP ERL Y GRO UNDED! FAI L URE TO DO SO CAN RESU LT IN SEVERE PERSONAL INJURY FROM ELECTRICAL SHOCK! This unit is pr ovided with an equipot ent ial grounding lug t hat is t o be proper ly att ached t o the rear of the f ram e by the aut horized ins taller .
3 Models C 81 0 & C8 12 To the Opera tor Section 2 To the Operator The gr ill you have purc hased has been c arefully engineered and manuf act ured t o provide dependable operat ion. This gr ill, when pr operly oper ated and maint ained, will produce a c onsist ent qualit y produc t.
4 Mo del s C810 & C812 Safety Se cti on 3 Sa fety We, at T aylor Company, ar e concerned about the safet y of the oper ator when he or she com es in contac t wit h the gr ill and its parts . T aylor has gone to ext rem e eff ort s to des ign and manuf actur e built- in saf ety f eatur es t o protec t bot h you and t he serv ice technic ian.
5 Mo del s C810 & C812 Safety DO NOT use c old water or ice t o cool t he upper plat en or the lower cook s urfac e. F ailure t o follow this i nstr ucti on may result in: S serious electr ical sh.
6 Mo del s C810, C812, C816, C818 O perat or P arts Id en tif icat io n 101006 Section 4 Operator Parts Identif ication C810 E xploded V iew Figur e 1 ITE M DESCRIPTI ON PART NO. 1 CAN-GREASE 073294 2 SLIDE- GREASE CAN 073293 3 PANEL A.- SIDE-UPPER * LEFT X72962 4 PANEL-SI DE-LOWER * LEFT 073262 *5 KIT A.
7 Mo del s C810 & C812 Op erato r Parts I den ti fi cati on C812 E xploded Vi ew Figur e 2 ITE M DESCRIPTI ON PART NO. 1 CAN-GREASE 073294 2 SLIDE- GREASE CAN 073293 3 PANEL A.- SIDE UPPER-LEFT X72962 4 PANEL-SI DE-LOWER- LEFT 073262 5 PLATEN A.- 2600W 208V X73272-23 6 PANEL-BACK- LOWER 073432 7 PANEL A.
8 Mo del s C810 & C812 Op erato r Parts I den ti fi catio n 1 10207 Accessor ies Figur e 3 ITE M DESCRIPTI ON PART NO. 1 SHEET-RELEASE ( BOX 9) 073442 *2 RETAINER- SHEET RELEASE (RETENTI ON BAR) 072845 **3 CLIP- RELEASE MATERIAL W/TAB 072673 4 SCRAPER-TEFLON WI PER 075887 ITE M DESCRIPTI ON PART NO.
9 Models C 81 0 & C8 12 Impor tant : To the Opera tor Section 5 Important: To the Operator Figur e 4 ITE M DESCRIPTI ON 1 RAISE BUTTON 2 STANDBY/COOK MODE BUTTON 3 MASTER POWER SWITCH 4 CLEAN MODE.
10 Models C810 & C812 Operating Procedures Section 6 Operating Procedures The Model C810 has three independent upper platens. The Model C812 has two independent upper platens. These grills are capable of cooking a variety of products and feature two cooking options.
11 Models C810 & C812 Operating Procedures Step 4 Place the release material clips over the release material sheet. Press them into place over the release material bar at the top of the platen. Figure 8 Step 5 Check the tightness of the release material against the upper platen.
12 Models C810 & C812 Operating Procedures Care of Release Material Sheets S DO NOT fold or crease. Figure 11 S DO NOT touch with any sharp object or abrasive.
13 Models C810 & C812 Operating Procedures Figure 15 When the grill is at the proper temperature, the temperature statements will no longer display and the temperature indicators will be illuminated in green. Figure 16 Programming Menu Items To enter the Program Mode, the grill control must be in the OFF or IDLE mode.
14 Models C810 & C812 Operating Procedures Step 3 The PROGRAM MODE screen will appear. Figure 19 UNITS Key The UNITS key is used to select either English or metric units of measure. The UNITS key toggles between English or metric units with each key press.
15 Models C810 & C812 Operating Procedures To edit a menu item, press the menu item key to bring up a virtual keyboard. Type in the desired name (up to 8 characters per line) and then press the “X” key to return to the previous screen. Figure 23 ACTIVE: YES or NO.
16 Models C810 & C812 Operating Procedures Patty Placement Placement procedures of meat products must be followed on the grill. The meat must be placed on the lower grill surface from front to back. When the cook cycle is complete, the upper platen will raise.
17 Models C810 & C812 Operating Procedures Operating Procedures Cooking Product Step 1 Select the menu item to be cooked. The grill is at the correct temperature if the control does not display any temperature statements and the grill temperature indicators are green.
18 Models C810 & C812 Operating Procedures Standby Procedures Whenever the grill is idle and product is not being cooked, the upper platen must be placed in the STANDBY position. Step 1 To place the upper platen in the STANDBY position, press the STANDBY button twice from the open position.
19 Models C810 & C812 Operating Procedures Step 2 Use the wiper squeegee to clean the release material sheet on the upper platen. Use a diagonal motion to clean the sheet. Hold the handle at a slight upward angle with the wiper end facing downward.
20 Models C810 & C812 Operating Procedures Step 2 Press the CLEAN key. When the cook surfaces reach the proper temperature for cleaning, an alarm will sound and the message “READY TO CLEAN” will be displayed. Figure 34 Step 3 Press the RAISE button to cancel the alarm.
21 Models C810 & C812 Operating Procedures Step 6 Remove the release material clip, the release sheet retainer, and the release material sheet. Take these parts to the sink to be washed and rinsed. Figure 38 Step 7 Repeat steps 1 through 6 for the remaining upper platen(s).
22 Models C810 & C812 Operating Procedures 1 10204 Step 13 Using an approved high temperature grill cleaner, pour approximately 3 oz. (90 ml) onto each 12” (305 mm) cook zone. Figure 43 Step 14 Firmly attach a non-abrasive pad to the pad holder.
23 Models C810 & C812 Operating Procedures Step 21 C810: Apply grill cleaner to both sides of the center platen. Step 22 Apply grill cleaner to the inner edges of the right and left platens. Step 23 Press the RAISE button to raise the lowered platen.
24 Models C810 & C812 Operating Procedures Step 34 C810: Press the STANDBY button to lower the center platen. C812: Press the STANDBY button to lower one of the platens, if needed. Step 35 C810: With a clean, wet cloth, rinse both sides of the center platen.
25 Models C810 & C812 Operating Procedures To avoid damaging the grill: S Never use grill screens on the upper platen or the lower grill surface. S Never use any abrasives or cleaners other than the approved cleaner. S Never allow the grill scraper or the abrasive cleaning materials to come in contact with the release material.
26 Models C810 & C812 Operating Procedures Non-24 Hour Stores Only: Step 48 Wipe all areas with a clean, wet cloth. Step 49 Wipe all exterior panels. Step 50 Apply a light coat of vegetable oil to the entire lower grill plate. Figure 55 Step 51 Leave the upper platens in the OPEN position overnight.
27 Models C810 & C812 Troubleshooting Guide Section 7 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY 1. One side of the grill will not heat. The control will display the message, “FAULTY ELEMENT OR SHORTED PROBE” after the TOO COOL timer has elapsed.
28 Models C810 & C812 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY 6. The upper platen will not stay in the COOK or STANDBY position. a. Temperature is insufficient to satisfy the indicator LED's. a. Wait until the indicator L ED's turn green.
29 Models C810 & C812 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY 12. The product is under-cooked or overcooked. a. The release material sheet is worn. a. Replace the release material sheet. b. Incorrect cooking time. b. Reset the processor control for the correct time.
30 Models C810 & C812 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY 16. The display reads “HOME SWITCH NOT SEEN.” a. Defective motor control. a. Call a service technician. b. Defective stepper motor. b. Call a service technician. c. Defective stepper motor wire harness.
Section 8 Parts List 31 Mo del s C810 & C812 Parts List DESCRI PT IO N PART NUMBER C810 QTY. WARR. CLASS RE MARKS C81023G000 ADAPTOR-1/ 4MPT X 1/4 OD TUBE 052563-2 1 103 BACKSPLASH A. X72954 1 103 BAR A.- RELEASE MATERIAL X72843 3 103 PLATEN COVER +NUT-10- 32 WHIZ FLANGE LOCKNUT 020983 9 000 +SCREW-SHO ULDER 10-32X1/ 4X.
32 Parts L ist Mo del s C810 & C812 DESCRI PT IO N REMARKS WARR. CLASS C810 QTY. PART NUMBER CASTER-5" 7- 5/8 STEM 078377 2 103 CASTER-GRI LL 5" SWI VEL W/LOCK 073240 2 103 +BRACKET-CAST.
33 Mo del s C810 & C812 Parts List DESCRI PT IO N REMARKS WARR. CLASS C810 QTY. PART NUMBER GAUGE-130 PSI 1/8 MPT BACK MNT 072695-3 1 103 MANI FOLD A.-* C842* GASKET-CONTROL * C842* 072914 3 000 GUIDE- PATTY PLACEMENT GEN MKT 073440 1 103 HANDLE-PLATEN 073250 3 103 HARNESS A.
34 Parts L ist Mo del s C810 & C812 DESCRI PT IO N REMARKS WARR. CLASS C810 QTY. PART NUMBER FASTENER-SNAP I N 1/4X15/16 078329 24 000 LABEL-ELEC- CAUTION 075484 1 000 MANIFOLD A.
35 Mo del s C810 & C812 Parts List DESCRI PT IO N REMARKS WARR. CLASS C810 QTY. PART NUMBER PL UG -HO LE 1 -3/4 D IA. 027132 3 000 PL UG -HO LE 1 -3/8 D IA.
36 Parts L ist Mo del s C810 & C812 DESCRI PT IO N REMARKS WARR. CLASS C810 QTY. PART NUMBER SWITCH- PRESSURE 240V,3HP 077879-C 1 103 COMPRESSOR A.
37 Mo del s C810 & C812 Parts List DESCRI PT IO N REMARKS WARR. CLASS C810 QTY. PART NUMBER C81075GW 00 - ROHS COMPLIANT 400V 50HZ 3N~ (4 WI RE) ELECTRIC CONTROL-HI -LIM IT 550F NO RESET 074165 9 103 DIAGRAM- WIRING * C810* 073479-75 1 000 FILTER A.
38 Parts L ist Mo del s C810 & C812 DESCRI PT IO N PART NUMBER C812 QTY. WARR. CLASS RE MARKS C81223GW 40 ADAPTOR-1/ 4MPT X 1/4 OD TUBE 052563-2 1 103 BACKSPLASH A. *C812* X73651 1 000 BAR A.- RELEASE MATERIAL X72843 2 103 PLATEN COVER +NUT-10- 32 WHIZ FLANGE LOCKNUT 020983 6 000 +SCREW-SHO ULDER 10-32X1/ 4X.
39 Mo del s C810 & C812 Parts List DESCRI PT IO N REMARKS WARR. CLASS C812 QTY. PART NUMBER CASTER-GRI LL 5" SWI VEL W/LOCK 073240 2 103 CLEVIS- ROD 1/2-20 THD 079777 2 103 COMPRESSOR-AI R-230V SERV 032129SER2 1 212 +ADAPTOR-HI TEMP 1/4X1/4 OD 058769-2 1 103 +F ITT ING -HI T EM P 1 /4X 1/4 OD 9 058771-2 1 103 + MANIFOLD A.
40 Parts L ist Mo del s C810 & C812 DESCRI PT IO N REMARKS WARR. CLASS C812 QTY. PART NUMBER GUIDE- PATTY PLACEMENT GEN MKT 073440 1 103 HANDLE-PLATEN 073250 2 103 HARNESS A.- COMP. VALVE * C842 X72743 1 103 HARNESS A.- COMP. VALVE * C832 X73145 1 103 HARNESS A.
41 Mo del s C810 & C812 Parts List DESCRI PT IO N REMARKS WARR. CLASS C812 QTY. PART NUMBER LABEL-ELEC- CAUTION 075484 1 000 MANIFOLD A. -*C832* 073129 1 103 CONNECTOR-MATE LOCK 4 CI R-PIN 500534 1 103 PIN- .
42 Parts L ist Mo del s C810 & C812 DESCRI PT IO N REMARKS WARR. CLASS C812 QTY. PART NUMBER PLUG-HOLE 3/ 8 DIA BLACK PLASTI 050988 1 103 PULLEY-PLATEN CABLE 072662 4 103 PULLEY-PLATEN- LEFT 07324.
43 Mo del s C810 & C812 Parts List DESCRI PT IO N REMARKS WARR. CLASS C812 QTY. PART NUMBER SWITCH- SCREW TERMINAL 075780 2 103 LATCH SWITCH TANK-ACCUMULATOR 10LB- NPT 078820 1 103 TEE-1/ 4FPT X 1/4MPT X 1/ 4FPT 021277 1 103 AI R COMPRESSOR TEE-1/ 4OD X 1/4OD X 1/ 4OD TUBE 052562 1 103 AIR COMPRESSOR THERMOCOUPLE A.
Model C 810 073370-23 9/14/ 10.
Model C 810 073479-75 9/14/ 10.
Model C 812 073692-23 9/15/ 10.
An important point after buying a device Taylor C810 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Taylor C810 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Taylor C810 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Taylor C810 you will learn all the available features of the product, as well as information on its operation. The information that you get Taylor C810 will certainly help you make a decision on the purchase.
If you already are a holder of Taylor C810, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Taylor C810.
However, one of the most important roles played by the user manual is to help in solving problems with Taylor C810. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Taylor C810 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
