Instruction/ maintenance manual of the product CDP-50 Tangent
Go to page of 20
O p e r a t i o n M a n u a l CDP -50 CD-Pla yer.
01 ACCESSORIES Accessories 1 x CDP-50 1 x Remote control 2 x Batteries (Optional) 1 x Operation manual This operation manual supplies all the information that you need to have about your T angent CDP-50.
02 CONTENTS ACCESSORIES Accessories 01 CONTENTS Contents 02 SAFETY PRECAUTIONS Safety precautions 03 IMPORT ANT SAFETY INSTRUCTIONS Important safety instructions 04 IMPORT ANT INFORMA TION Important i.
TO MINIMISE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE. DO NOT OPEN THE CABINET AS IT CONT AINS DANGEROUS VOL T AGE.
W ARNING: IT IS IMPORT ANT THA T YOU READ AND OBSERVE BOTH THE INSTRUCTIONS IN THIS MANUAL AND THE INSTRUCTIONS ON THE UNIT . KEEP THIS MANUAL FOR FUTURE REFERENCE. This unit was designed and manufactured with a view to providing maximum safety for the user .
Service Do not attempt to carry out any service work yourself. By opening or removing the cabinet, you will be exposed to dangerous voltage or other hazards.
IMPOR T ANT INFORMA TION Handling instructions The top and back panel of the unit may become warm after prolonged use. This is not due to a defect. T urn off the power when the unit is not used.
07 CONNECTION Do not turn on the power before all connections have been made correctly . Check that all connections have been made correctly before turning on the power .
08 REMOTE CONTROL Installation of batteries Remove the cover as illustrated. Position two batteries of the type AAA/R03/UM4 in the battery compartment. Make sure that the orientation of the batteries is correct (see drawing at bottom). Replace the cover .
09 Some of the functions of the unit can only be performed by means of the remote control. Some functions are connected with the selected signal input source. Some buttons on the remote control may therefore not be available if the corresponding signal input source has not been selected.
8 9 1 0 1 2 3 4 5 6 7 10 FRONT P ANEL AND CONNECTIONS Front panel Mains switch: Used to interrupt the mains voltage. LED indicator: Lights green when the unit is turned on. Lights red when the unit is in standby mode or in operation. Program: Makes it possible to play the tracks of a CD a certain order .
1 1 FRONT P ANEL AND CONNECTIONS Connections 1 2 3 Stereo Output: Analogue stereo output. For connection to stereo amplifier or receiver with analogue input. Optical Output: Optical SPDIF output. For connection to stereo amplifier or receiver with digital input.
12 CONNECTION Audio connection layout Subwoofer (Optional).
13 OPERA TION AND FUNCTIONS PH ON O PO WE R CD P- 50 C D- PLA YE R 1 3 3 T urn on the unit by pressing the mains switch. Press the standby button on the remote control to switch to standby mode. The display will turn of f and all functions will be reduced to a minimum to make sure that the unit uses minimal power .
14 OPERA TION AND FUNCTIONS Pause - 8 8 4 - 0:38 Press the PLA Y/P AUSE button once more to stop playback. The small play symbol will disappear , and a small pause symbol will be displayed instead. T o continue playback, press the PLA Y/P AUSE button again.
15 OPERA TION AND FUNCTIONS Forward and rewind - 8 8 5 - 2:35 It is possible to perform a search in the track played. If you wish to search forward, depress the >> (next) button until you get to that part of the track that you wish to hear . Y ou will see that the time counter in the display counts up very quickly .
16 OPERA TION AND FUNCTIONS Program Repeat - 8 8 1 5 -58:34 The CDP-50 can be programmed to play the tracks of a CD in a certain order . Press the PROGRAM button when playback has been stopped. The MEMOR Y symbol and "Pr p:01" will be displayed.
17 TROUBLESHOOTING T roubleshooting PROBLEM CAUSE/REMEDY No power when unit is turned on. - Switch on the electric current at the socket. - Check that the plug has been correctly inserted into the socket. - The internal fuse has blown and must be replaced by a qualified service technician.
18 TECHNICAL DA T A T echnical data Output voltage 0.7V+/-2dB Frequency characteristics (Reference: 1kHz 0dB) 20 Hz 0dB -0.5 dB +/- 1 dB 100 Hz 0dB 0 dB +/- 1 dB 10 kHz 0dB -0.5 dB +/- 2 dB 20 kHz 0dB -3.0 dB +/- 2 dB Channel balance < 2.0 dB Separation > 60 dB Harmonious distortion (T H D + noise) < 0.
www . .c om tangent - audio.
An important point after buying a device Tangent CDP-50 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Tangent CDP-50 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Tangent CDP-50 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Tangent CDP-50 you will learn all the available features of the product, as well as information on its operation. The information that you get Tangent CDP-50 will certainly help you make a decision on the purchase.
If you already are a holder of Tangent CDP-50, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Tangent CDP-50.
However, one of the most important roles played by the user manual is to help in solving problems with Tangent CDP-50. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Tangent CDP-50 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
