Instruction/ maintenance manual of the product ISDN GW 3201 TANDBERG
Go to page of 18
Codian ISDN Gateway ISDN GW 3201 Series Getting started.
Codian ISDN GW ISDN GW 3201 Series Getting started.
Copy right © Codian 2008. All rights reser ved. This Getting Star ted Guide ma y not be copied, photocopied, translated, r eproduc ed, or con verted into any electronic or machine-readable form in whole or in par t without prior wr itten appro v al of Codian Limited.
T able of conten ts General inf ormation .......... .......... .......... ........... .......... .......... ............. .......... ........... .......... .. .... . 1 About the ISDN g ateway .......... ........... ............ .......... ........... .
General information 1 General informa tion About the ISD N gatewa y The ISDN GW 3201 Series is a range of high perfor mance video gatew a ys which enables ISDN netw ork connectivity for the Codian IP-based video infrastr ucture products as w ell as IP-based endpoints.
2 LED behavior T able 1 descr ibes the behavior of the LEDs . T able 1: ISDN gateway LED behavior LED Co lor Indicates Compact Flash Activity Flashing gr een One of: the ISDN gatewa y is booting .
General information 3 Ethernet P or t Status , for each Ether net por t: FDX Green The link has been negotiated as a full-du plex link Act Gr een Pa ckets are being transmitted on this por t Link Gree.
4 Connecting the ISDN gatew ay Befor e you start Y our ISDN connection Outside North America Check with your netw ork pro vider to ensure that your incoming ISDN PRI line is ter minated in an NTU/CSU (Netw ork T er m ination Unit/ Channel Ser vice Unit).
Connecting the ISDN gateway 5 Step one: Connect power Connect the po w er connector on the rear of the unit to the pow er supply using the supplied po wer ca ble .
6 Initial configur ation Step one: Connect to the console port 1 Ensure po wer is connected to the ISDN gate wa y and the Status LED is g reen. 2 Connect the console por t of the ISDN gate w a y to the ser ial por t of your PC using the bl ue RJ45 to DB9 console cable supplied.
Initial configuration 7 1 T o configure Ethernet Port A, enter the following for auto-sensing mode: ethertype auto or to configure a speed and duplex, use the follo wing command: ethertype <10|100&.
8 Configuring the ISDN ga teway Step one: Log in to the ISDN gate wa y All administration of the ISDN gate wa y is perfor med via the web interf ace . T o log in to the ISDN gatewa y: 1 Use your bro wser to na vigate to the IP addr ess of the ISDN gate wa y (to discov er the IP address, refer to the pr evious sectio n).
Configuring the ISDN gateway 9 Step three: C onfigure an H.323 gatek e eper If you ha ve H.32 3 endpoints, using an H.323 ga tekeeper can ma ke it easier for ca llers to make their call. Y ou can configure the ISDN gate wa y to use an exter nal gatekeeper or its o wn built-in gatek eeper .
10 ISDN to IP dial plan setup Options 1 and 2 will automaticall y handle both voice and video calls . Option 1 - This example assumes that y ou ha v e a PRI line that has 100 numbers (00 to 99) associated with it and tha t all your endpoints are r e gistered to a gatekeeper with registrations in the range 5900 - 5999.
Troubleshooting and tec hnical support information 11 T r oubleshooting and technical suppor t information Refer to this section if you ar e exper ienci ng difficulties with the ISDN gate wa y. Ensure that y ou ha ve follo w ed the instr uctions in this guide when installing and configuring the ISDN gatew ay.
12 Getting more help If the documentation does not an sw er your questio n or you ha v e a prob lem with one of our products: 1 Refer to the T echnical FA Q and T roubleshooter sections of the w eb site. W e keep both sections up to da te with the latest infor mation fr om our tec hnical suppor t team regarding the r esolution of customer issues .
Pin outs 13 Pin outs The pin numbering for the PRI por ts on the ISDN gatewa y is shown in Figur e 2. The pin assignments for the PRI por ts are sho wn in T able 2: Figur e 2: Pin numbering for PRI po.
61-0019-03.
An important point after buying a device TANDBERG ISDN GW 3201 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought TANDBERG ISDN GW 3201 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data TANDBERG ISDN GW 3201 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, TANDBERG ISDN GW 3201 you will learn all the available features of the product, as well as information on its operation. The information that you get TANDBERG ISDN GW 3201 will certainly help you make a decision on the purchase.
If you already are a holder of TANDBERG ISDN GW 3201, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime TANDBERG ISDN GW 3201.
However, one of the most important roles played by the user manual is to help in solving problems with TANDBERG ISDN GW 3201. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device TANDBERG ISDN GW 3201 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
