Instruction/ maintenance manual of the product TBC-230B Tanaka
Go to page of 20
Owner’ Owner’ Owner’ Owner’ Owner’ s Man s Man s Man s Man s Man ual ual ual ual ual Model Numbers: TBC-2211, TBC-2251,TBC-230/B TBC-2211, TBC-2251,TBC-230/B TBC-2211, TBC-2251,TBC-230/B TBC.
www.tanaka-usa.com 1 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B Before using this unit: • Read the operator’s manual carefully. • Check that the cutt ing equipment is correctly assembled and adjusted. • Start the unit and check the carburetor adjustment.
www.tanaka-usa.com 2 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B Blade thrust may occur when the spinning blade contacts a solid object in the critical area. A dangerous reacti on may occur causing the entire unit and operator to be thrust violently.
www.tanaka-usa.com 3 custsvc@tanaka-i sm.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B 1. What is What? Since this manual covers several models, there m a y be some difference between pictures and your unit. Use the instructions that apply to your unit.
www.tanaka-usa.com 4 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B 2. Warnings and safety instructions. Operator Safety • Always wear a safet y face shield or goggles . • Always wear heavy, long pant s, boo ts and gloves. Do not wear loose clothing, jewelry, short pants, sandals or go barefoot.
www.tanaka-usa.com 5 custsvc@tanaka-i sm.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B 3. Assembly procedures Drive shaft to engine (Fig. 1 -1) Loosen tube locking bolt (1) about ten turns so that the bo lt tip will not obstruct drive sh aft tube to be inserted.
www.tanaka-usa.com 6 custsvc@tanaka-i sm.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B Throttle wire/stop cord Remove the air cleaner cover. (Fig. 1-4) Connect stop cords. (Fig. 1 -5) Set outer receiver (1) (if so provided) into wire guide and put throttle wire through the outer receiver.
www.tanaka-usa.com 7 custsvc@tanaka-i sm.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B When using a trimmer head (2) with a two piece type blade guard, attach the guard extension to the blade guard. (Fig. 1-9) Then loca te the guard above the gear case.
www.tanaka-usa.com 8 custsvc@tanaka-i sm.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B 4. Operating procedures Fuel (Fig. 2-1) WARNING! The trimmer is equipped with a two-stroke engine. Always run t he engine on fuel, which is mixed with oil. Provide good ventilation, when fueling or handling fuel.
www.tanaka-usa.com 9 custsvc@tanaka-i sm.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B CAUTION! Before starting, make sure the cutting attachment is not touching anything. Starting (Fig. 2-2, 2B) 1. Set ignition switch (1) to the ON position. (Fig.
www.tanaka-usa.com 10 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B Cutting (Fig. 2-4, 4B, 4C, 4D) • When cutting, operate engine at ov er 6500 rpm. Extended use at a slow speeds may wear the clutch prematurely. • Cut grass from right to left.
www.tanaka-usa.com 11 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B 5. Maintenance MAINTENANCE, REPLA CEMENT, OR REPAIR OF THE EMISSION CONT ROL DEVICES AND SYSTEMS MAY BE PERF ORMED BY ANY NONROAD ENGINE REPAIR ESTABLISHMEN T OR INDIVIDUAL.
www.tanaka-usa.com 12 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B NOTE! If element is hard due to excessive dirt buildu p , re p lace it. Drain all fuel from fuel tank and pull fuel filter line from tank. Pull filter element out of holder assembly and rinse element in warm water with detergent.
www.tanaka-usa.com 13 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B Flexible drive shaft (Fig. 3-5) Flexible drive shaft should be rem oved and lubricated with a good quality lithium grease every 20 hours.
www.tanaka-usa.com 14 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B Maintenance schedule Below you will find some genera l maintenance instructions. For further information please contact your Tanaka service dealer. Daily maintenance • Clean the exterior of th e unit.
www.tanaka-usa.com 15 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B 6. Optional Installation of free disk set (optional) (Fig. 4-1, 1 B) 1) Disassemble free disk (7) from the free disk set by loosening three bolts (8). 2) Place blade (3) as shown in drawing.
www.tanaka-usa.com 16 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B 7. Specifications NOTE: Sound levels are calculated as the time-weighte d energy total under v arious working conditions with the following time distribution: ½ idling, ½ racing.
www.tanaka-usa.com 17 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B Declaration of conformity D6claration de conformit6 Dichiarazione di conformita Konformitiitserkliirung Declaraci6n de conformidad Konformitetsdeklaration Tanaka Kogyo Co.
www.tanaka-usa.com 18 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B IMPORTANT NOTICE THIS INFORMATION IS FOR TH E US AND CANADIAN MARKETS ONLY. • To reduce the risk of injury from loss of control, never use a metal blade on a curved shaft gr ass trimmer.
www.tanaka-usa.com 19 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B Cutting Attachments for Tanaka Trimmers and Brushcutters 1) Fixed line commercial cutting heads offer excellent dur ability and light weight. Great for commercial use.
An important point after buying a device Tanaka TBC-230B (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Tanaka TBC-230B yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Tanaka TBC-230B - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Tanaka TBC-230B you will learn all the available features of the product, as well as information on its operation. The information that you get Tanaka TBC-230B will certainly help you make a decision on the purchase.
If you already are a holder of Tanaka TBC-230B, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Tanaka TBC-230B.
However, one of the most important roles played by the user manual is to help in solving problems with Tanaka TBC-230B. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Tanaka TBC-230B along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
