Instruction/ maintenance manual of the product AST-7000 Tanaka
Go to page of 8
Owner’ Owner’ Owner’ Owner’ Owner’ s Man s Man s Man s Man s Man ual ual ual ual ual Model Numbers: AST-7000 AST-7000 AST-7000 AST-7000 AST-7000 A A A A A UT UT UT UT UT O-ST O-ST O-ST O-ST O-ST AR AR AR AR AR T TRIMMER T TRIMMER T TRIMMER T TRIMMER T TRIMMER Date 04-19-01 Supplier T o The Outdoor P ower Equipment Industry ISM, Inc .
www.tanakapowerequipment.com 1 custsvc@tanaka-ism.com Owner’s Manual AST-7000 Major Parts Since this manual covers several models, there may be some difference between pictures and your unit.
www.tanakapowerequipment.com 2 custsvc@tanaka-ism.com Owner’s Manual AST-7000 GENERAL INSTRUCTIONS FOR SAFETY OPERATION All the TANAKA products are delivered with an Owner's manua l. Please read it carefully to get acquainted with the operation of your unit.
www.tanakapowerequipment.com 3 custsvc@tanaka-ism.com Owner’s Manual AST-7000 I. IMPORTANT SAFETY INSTRUCTIONS 1. Do not depress the "Start Button" while recharging the battery. This will result in damage to the battery charger. The battery charger must be disconnected from the unit before starting.
www.tanakapowerequipment.com 4 custsvc@tanaka-ism.com Owner’s Manual AST-7000 4. Installation of safety guard (Fig. 4 & 5) 1. Secure the safety guard to the shaft as shown in Figure 4. NOTE: The safety guard must be installed 5" from the top of the gear case as shown in figure 5.
www.tanakapowerequipment.com 5 custsvc@tanaka-ism.com Owner’s Manual AST-7000 (III. Operating Procedures cont.) 2. Starting Procedure The AST-7000 battery is not fully charged at the factory. It is necessary to charge it fully before operation. Please follow "C harging Procedures".
www.tanakapowerequipment.com 6 custsvc@tanaka-ism.com Owner’s Manual AST-7000 (III. Operating Procedures cont.) 6. Carburetor adjustment: (Fig. 14 & 15) The carburetor has been preset at the factor y and probably won't require adjusting.
www.tanakapowerequipment.com 7 custsvc@tanaka-ism.com Owner’s Manual AST-7000 (IV. Maintenance cont.) 2. Blade 1. When replacing blade, purchase one recommended by TANAKA, with a 25.4 mm (one inch) fitting hole. 2. When installing saw blade, always face the stamped side up.
An important point after buying a device Tanaka AST-7000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Tanaka AST-7000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Tanaka AST-7000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Tanaka AST-7000 you will learn all the available features of the product, as well as information on its operation. The information that you get Tanaka AST-7000 will certainly help you make a decision on the purchase.
If you already are a holder of Tanaka AST-7000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Tanaka AST-7000.
However, one of the most important roles played by the user manual is to help in solving problems with Tanaka AST-7000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Tanaka AST-7000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
