Instruction/ maintenance manual of the product SF-10V Barco
Go to page of 58
SF-1 0V dis play Install ation manual R59770542/01 10/02/2012.
Barco nv Liv eDots President Kennedypark 35, B-8500 Kortrijk Phone: +32 56.23.32.11 Fax: +32 56.26.22.62 Support: www.barco.com/esupport Visit us at the web: www.
Changes Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war- ranties or merchantability and fi tness for a particular purpose.
.
Tabl e of c ont ents T ABLE OF C ONTEN TS 1 . S a f e t y ...... ...... .... ...... .... .... ...... .... ...... .... ...... .... ...... .... .... ...... .... ...... .... ...... .... ...... .. 3 1 . 1 S a f e t y g u i d e l i n e s ..................
Tabl e of co nt ents 2 R59770542 SF-10V DISPLAY 10/02/2012.
1. Safety 1. SAFETY About this chapter Read this chapter att entively . It contains important information to prevent personal injury while installing the SF -10V display . Further- more, it includes several cauti ons to prevent damage to the SF-10V tile.
1. Safety 1.1 Safet y guidelines Personal prot ection W ARNING : Ensure you understand and follow all the safety guidelines, safety instructi ons, w arnings and cauti ons menti oned in thi s manual. W ARNING : Be aware of suspe nded loads. W ARNING : Wear a hard hat to reduce the risk o f personal injury .
1. Safety 1.2 Important safety instructions Instructio ns: • Read these instructions. • Keep these instructions. • Heed all warnings . • Follow all inst ructions. • Clean only with materials or chemicals that are inert, nonabrasive, noncorrosive and non-marking.
1. Safety 1.3 Importa nt warnings Important warnings: Risk of elect ric shock: Do not open. T o reduce the risk of electric shock, do not remove cover (or back) . Remove all power and data cabling befor e opening the device for service purposes. No user-servic eable parts inside.
2. SF-10V tiles 2. SF-10V T ILES About this chapter This chapter described the SF-10V , modu lar outdoor LED tile. Overview • SF-10V tile • Stacking SF-10V packages R59770542 SF-10V DISPLAY 10/02/.
2. SF-10 V tiles 2.1 SF-10V ti le T ile o ver view The front and back v iew of the SF-10V tile. Image 2-1 Packing For safe transport ation, the SF-10V til es are stored in a s ecure way . every ti le have its separ ate package, Maxium 4 SF-10V pack- ages that inner hold the ti le can stand in a big wooden pallet.
2. SF-10V tiles 2.2 S tacki ng SF- 10V p acka ges Stacking possibilitie s for SF-10 V packages Image 2-3 W ARNING : Only th e con fi gur ations i llu strat ed abo ve can be used f or st acking. Other con fi gur ation s will da m- age the SF-10V tiles.
2. SF-10 V tiles 10 R59770542 SF-10V DISPLAY 10/02/2012.
3. Inst allati on requireme nts 3. INST ALLA TION REQUIREMENTS About this chapter This chapter enumerate t he mechanical r equirements for the SF -10V display , the electr ical requi rements to power up t he SF-10V display and the sy stem requirements to run the control software ef fi cient.
3. In stal latio n requ irem ents 3.1 Mechanical requirements for the SF-10V display Support str ucture The support structure can be provided and installed by the c ustomer because they vary from s ystem to system. Although, the following must be taken into account and must be precisely calcul ated on individual basis: 1.
3. Inst allati on requireme nts W ARNING : 90% energy is transferred into heat, which req uires a certain amount of air fl ow at the rear of the SF-1 0V displ ay . Fo r that suf fi cient free space should be available behind the display to ensure a good venti lat ion.
3. In stal latio n requ irem ents 3.2 Electrica l requirements for the SF-10V display Power requireme nts One SF-10V tile r equires 220-240 V AC, 50-60 Hz, 5.72 amps at 230 V AC. Note that one SF-10V ti le correspond wit h a display surf ace of 1,23 m².
3. Inst allati on requireme nts 3.3 System requirements for th e Control s oftware Bef ore you b egi n It is assumed you ar e familiar with the Windows operating s ystem at your site. The CD-ROM in your package contains a Windows-based instal lation program.
3. In stal latio n requ irem ents 16 R59770542 SF-10V DISPLAY 10/02/2012.
4. Sy stem over view 4. SYSTEM OVERVIEW About this chapter This chapter enumerates t he fundamental elements of an SF-10V screen display . Overview • Introduction • SF-10V tile • Power boxes •.
4. S ystem overv iew 4.1 Introduction The fundamental eleme nts of an SF-10V screen display system are : • SF-10V tiles. • Control PC. • LED Image P rocessor .
4. Sy stem over view Sources Control PC Power box TCP/IP T ile 1 LED-wall T ile 2 T ile 3 V ideo Processor Image 4-2 If th e LED Image Processor is DX–700 and DX-100 use the TCP/IP connecti on with the contr ol PC.
4. S ystem overv iew 4.2 SF-10V ti le Introduction SF-10V tile The SF-10V series is designed for ultra-large outdoor LED display installat ions. The SF-10V tile can overlay video and data sources in their nat ive quality .
4. Sy stem over view Image 4-4 Power link ca ble of 1,5 m eter ( R98502 41 ). R59770542 SF-10V DISPLAY 10/02/2012 21.
4. S ystem overv iew Image 4-5 Dummy power plug ( R9850 280 ). Data cables u sed betwee n SF-10V tile s T o meet the d emands of each SF-10V application Barco offers several lengths o f data cables to link data f rom tile to tile. Not e that the data output port of the last SF-10V tile in the data chain has to be s ealed with a dummy data plug.
4. Sy stem over view Image 4-6 Data linking c able of 1,5 m eter ( R9850210 ). R59770542 SF-10V DISPLAY 10/02/2012 23.
4. S ystem overv iew Image 4-7 D u m m yd a t ap l u g( R9850270 ). 24 R59770542 SF-10V DISPLAY 10/02/2012.
4. Sy stem over view 4.3 Power boxes Gene ral T o ensure safe and reliable operation of the SF-10V display , a suitable system for AC power distribution must be used. Though 3 rd . party solutions may be used, several sizes and types of power distributions are available from Barco.
4. S ystem overv iew 4.4 V ideo Processor Gene ral The Video processor processes (image processing, conversion and conditioning) all source signals for digital dis tribution to every tile as well as providing a user interface for complete system setup monitoring and control.
4. Sy stem over view C AUTION : Refer to the manual(s) of the used video processor for mo re information about installation and usa ge guid elines . D320 The D320L is a video processing device, designed to dr ive as well Barco LED walls as large screen projectors, monitors, plasma screens, .
4. S ystem overv iew 4.5 Control software Gene ral The control sof tware is designed as a graphic user inter face (GUI) and can be used to control and con fi gure the digitizer as well as the Barco LED wall via a P C (e.g. D irector toolset) . Minimum required software version: 2.
4. Sy stem over view 4.6 Fiberlink system Gene ral If the distance between the digiti zer and the LED-wall exceeds 5 meters, a fi ber optic connection must be used to ensure signal integrity and s ystem reliability . Barco offer s two complete system solutions including transmit ter , fi b er and receiver .
4. S ystem overv iew 30 R59770542 SF-10V DISPLAY 10/02/2012.
5. Ph ysic al inst allation 5. PHYSICAL INST ALLA TION About this chapter The setup process below describes roughly the installation s tages to follow to install a SF-10V display . Several stages refer to one or more detailed and i llustrated procedures which are also described in t his installation manual.
5. Ph ysic al inst allation 5.1 Installation of the support s tructure What has to be done? The complete support structure has to be assembled and installed in its fi nal position. Screen supporti ng/securi ng structur es vary from system to system. Consult Bar co for advise on professio nal riggi ng org anizat ions .
5. Ph ysic al inst allation 5.2 Mounting the SF-10V tile Necessary t ools • 17 mm open-end w rench. • 17 mm box-end wrenc h. • 14 mm long allen key . • Scaffold or Z-lift. Necessary p arts • SF-10V tiles • Four M10x90 bolts per tile (D IN931 hex cap bolts and par tially thread - steel zinc plated).
5. Ph ysic al inst allation 1 2 3 5 4 4 6 7 8 10 9 Image 5-3 1. Adjust bloc k 2. Hoist point. 3. Hoist point. 4. Adjust bloc k 5. Insert nuts f or fi xing tile 6 Handle 7. Insert nuts f or fi xing tile 8. Handle 9. Insert nuts f or fi xing tile 10.
5. Ph ysic al inst allation 4X B A Image 5-5 4. Place a prevailing torque for the bolt (reference A) with the wa sher (reference B ) on eac h insert nuts of tiles.
5. Ph ysic al inst allation Example of SF-10V tile mounting 1 2 3 4 5 6 Image 5-6 How to get th e height align ment betw een tiles Open the back door , u sing the long allen key rotate the socket head screw that l ocated the bottom of til e as illustrated.
5. Ph ysic al inst allation A Adjust block screw. B Long allen key(14mm) About cabling of Data cable between tiles. Considering the position of the data in/out sockets in SF-10Vtiles and dataI cable length, the cabling w ays illustrated as foll ows are the only 2 possible ways.
5. Ph ysic al inst allation 38 R59770542 SF-10V DISPLAY 10/02/2012.
6. Dimensio ns 6. DIMENSIONS About this chapter This chapter contains drawings of the SF-10V tiles and its package, with the m ost important dimensions.
6. Dimensi ons 6.1 SF-10V ti le Dimensions of the SF-10V tile 1280 mm 480 mm 960 mm 910 mm 1200 mm 188mm 223.85mm M10 Image 6-1 40 R59770542 SF-10V DISPLAY 10/02/2012.
6. Dimensio ns 6.2 Assembly of SF-10V tiles Main dimensions of an a assembly of SF-10V tiles 910 mm 480 mm 80 80 1200 mm 80 1200 mm 80 1200 mm 80 910 mm 50 50 910 mm Image 6-2 R59770542 SF-10V DISPLAY.
6. Dimensi ons 6.3 SF-10V pack age Dimensions of the SF-10V tile package containing 4 tiles. 1364mm 1384mm 1424 mm 1041 mm 11 5 6 m m 1 15 mm 1092 mm 1032 mm Image 6-3 42 R59770542 SF-10V DISPLAY 10/0.
7. Spe cificat ion 7. SPECIFICA TION R59770542 SF-10V DISPLAY 10/02/2012 43.
7. Specifi catio n 44 R59770542 SF-10V DISPLAY 10/02/2012.
7. Spe cificat ion 7.1 S peci fi cations of theSF-10V tile Speci fi cations of the SF-10V tile Pix el Pi tch 20mm LED con fi gurati on 2R, 1G, 1B Pixel Density (real mod e) 2,500 px/m² Pixel Densi.
7. Specifi catio n Co mp ati bil ity D320L/Lite Ye s LedPro Ye s DX-700 Ye s DMP-100 No AEC-4000 (in combination with DTS) Ye s AEC-4000 (in combination with RMS) No Fiber link I I Ye s CA T5 Link Ye .
8. Order info 8. ORDER INFO About this chapter This chapter contains the order numbers of several important SF-10V peripherals. Overview • Order info • Spare part and service kits Consult the secu red partner zone on W WW.My b ar co .co m for an updated li st with orde r numbers of the avai l- able SF-10V products.
8. Order inf o 8.1 Order info List with order numbers for SF-10V products Order inf o Description R9004843B1 BME SF-10V 1TL BOX R9852560 BME P SLITE HOIST KIT R9852350 BME P SLITE RAIL KIT 896 R9850241 Power li nk cable of 1.5 m eter . R9850250 Power li nk cable of 4.
8. Order info R9851253 PO WER BO X 3 PHASE 380V 5 OUTPUT R9851254 PO WER BO X 3 PHASE 380V 6 OUTPUT R9850058 BME D LITE PWR B OX220 R838621 BME SF Middle Mounting Plate R838622 BME S F Side Mounting P.
8. Order inf o 8.2 S pare part and servic e kits Gene ral Barco provide s several kits for se rvicing SF -10V tiles. Below you fi nd an or der list of existing spare part and service kits. In the future new ki ts can be added t o this li st. C ontact Barco t o get an updated l ist.
9. Env ironmen tal informat ion 9. ENVIRONMENT AL INFORMA TION Overview • Disposal information • Rohs compliance R59770542 SF-10V DISPLAY 10/02/2012 51.
9. Envi ronmenta l info rmation 9.1 Disposal i nformati on Disposal Information W aste Electrical and Electronic Eq uipment This symbol on the product indicates that, un der the European Directive 2002/96/EC governing was te from electrical and electronic equipment, this product must not be disposed of with other municipal waste.
9. Env ironmen tal informat ion 9.2 Rohs compliance T ur key RoHS co mpliance Türkiye Cumhuriyeti: EEE Yönetmeli ğ ine Uygund ur . [Republic of T urkey: In conformity with the EEE Regulation] 中.
9. Envi ronmenta l info rmation O: Indicates that this t oxic or hazardous substance contained in all of the homogeneous m aterials for thi s part is below the limit requirement in SJ/T1 1 363-2006. X: 表示 该 有毒有 害物 质 至少在 该 部件的某一均 质 材料中的含量超出 SJ/T 1 1363-2006 标 准 规 定的限量要求 .
An important point after buying a device Barco SF-10V (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Barco SF-10V yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Barco SF-10V - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Barco SF-10V you will learn all the available features of the product, as well as information on its operation. The information that you get Barco SF-10V will certainly help you make a decision on the purchase.
If you already are a holder of Barco SF-10V, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Barco SF-10V.
However, one of the most important roles played by the user manual is to help in solving problems with Barco SF-10V. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Barco SF-10V along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
