Instruction/ maintenance manual of the product EH65 Subaru Robin Power Products
Go to page of 24
.
3 Y ear Limited Engine W arranty (Special T erm for W elder Application) (Effective with engines purchased from Robin America, W ood Dale, IL, after November 15, 1993) Robin America, Inc.
5 6 Safety Precautions Before operating the engine, read this manual and become familiar with it and the equipment. Safe and ef fi cient operation can be achieved only if the equipment is properly operated and maintained.
moving parts, etc. • Used engine oils have been identi fi ed by some state and federal agencies as causing cancer or reproductive toxicity . When checking or changing engine oil, take care not to ingest, breathe the fumes, or contact used oil.
9 10 Introduction ABOUT THIS MANUAL This manual covers the operation and maintenance of the horizontal- shaft Robin Subaru EH65 engines for welder applications (OHV220 Performer Series). Each operator of the power equipment should study this engine manual carefully and observe all of its instructions and precautions.
Description FEA TURES • Overhead valve arrangement enables high power , and low fuel and oil consumption • V -T win, four stroke design • Air-cooled and gasoline fueled • The light weight and compact design makes it easy to install and utilize for many applications.
13 14 Installation LOCA TING Locate the engine at least 1 meter (3.0 ft) away from buildings or other structures. Provide proper exhaust routing. Refer to EXHAUST SYS- TEM below . Do not use the engine near fl ammables or other hazard- ous materials such as trash, rags, lubricants, or explosives.
ENGINE OIL Recommendations Use premium quality motor oil, Class SJ or SL. Look for the SAE (Society of Automotive Engineers) or API viscosity grade. Referring to the table below , choose the viscosity grade appropriate for the ambient temperatures expected during the period of time until the next sched- uled oil change.
17 18 BA TTER Y CABLES Installation ST ARTER SWITCH A customer supplied starter switch or key switch is recom- mended for the starter motor . See table below for switch cable recommendations. WIRE GAUGE CABLE LENGTH CABLE DIA. A WG (BS) BWG SAE JIS Less than 1.
19 20 ENGINE WIRING DIAGRAM (6 PIN) Engine Speci fi cation Numbers: EH650DC2405 EH650DC2415 Wiring Diagram POWER TRANSMISSION Belt Drive If using a belt drive application, consider the following note.
22 21 Operation EXHAUST GAS IS DEADL Y! Exhaust gases contain carbon monoxide, an odorless and color- less gas. Carbon monoxide is poisonous and can cause uncon- sciousness and death.
23 24 In colder weather , the engine will take longer to begin running smoothly with the choke open. Do not operate the equipment until the choke is fully open.
25 26 ! W ARNING EXHAUST GAS IS DEADL Y! Never operate engine-powered equipment indoors without a proper exhaust system, ample fresh air ventilation and an operable carbon monoxide detector . 2. Use fresh gasoline and fi ll the fuel tank after each day’ s use to reduce problems with moisture condensation if this is a gasoline engine.
27 28 Periodic Maintenance MAINTENANCE, REPLACEMENT , OR REP AIR OF THE EMISSION CONTROL DEVICES AND SYSTEMS MA Y BE PERFORMED BY NON-ROAD ENGINE REP AIR EST ABLISHMENTS OR INDIVIDUALS. Periodic maintenance is essential for top engine performance. See the T able below as a guide for normal periodic maintenance.
Crankcase pressure can blow hot engine oil out the fi ll tube causing severe burns. Always stop the engine before removing the oil fi ll cap. If the engine is equipped with the long oil fi ll tube, turn the oil fi ll cap counterclockwise and lift it up.
31 32 10 DO NOT FILL TO A LEVEL ABOVE THE FULL MARK ON THE DIPSTICK. Drain the excess oil if too much has been added. T oo much oil can cause high oil consumption, high operating temperatures and oil foaming. T oo little oil can cause severe engine damage.
33 34 ! W ARNING ! W ARNING SP ARK PLUG MAINTENANCE AND REPLACEMENT Refer to the Speci fi cations for spark plug type and gap speci fi cations. Check and clean spark plugs every 200 hours. Replace plugs every 500 hours. T o prevent cross threading the spark plug, always thread it in by hand until it seats.
T roubleshooting The table below provides basic troubleshooting guidance. If you fail to resolve the problem after taking the corrective actions suggested, contact the equipment manufacturer or a Robin Subaru dealer . Many troubleshooting procedures present hazards that can result in severe personal injury .
37 38 Robin America has established the Robin Subaru Ful fi llment Center to take and ship orders to anyone wanting Robin Subaru reference material. This allows for the prompt ful fi llment of Robin Subaru part and service manuals, counter catalogs, price books and other support material to dealers and end users at the lowest possible price.
40 39.
(herein ROBIN AMERICA) as soon as the problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have a question regarding your warranty coverage, you should contact the Robin America Inc. Customer Service Department at 1-630-350-8200.
43 44 the part will be repaired or replaced by FUJI according to subsection (4) below . Any such part repaired or replaced under warranty will be warranted for the remainder of the period prior to the fi rst scheduled replacement point for the part.
How to remove the spark arrestor 1. Remove the fl ange bolts from the muf fl er cover and remove the muf fl er cover . 2. Remove the special screw from the spark arrestor and remove the spark arrestor from the muf fl er . Clean the spark arrestor screen Use a brush to remove carbon deposits from the spark arrestor screen.
INDUSTRIAL PRODUCTS DIVISION 4-410 Asahi, Kitamoto-shi Saitama, 364-851 1, Japan Phone +81(48) 593-7798 Fax +81(48) 593-7946 Web site http://www .fhi.co.jp/robin/ / 940 Lively Blvd. Wood Dale, IL 60191 U.S.A. Phone: 630-350-8200 Fax: 630-350-8212 Website: http://www .
An important point after buying a device Subaru Robin Power Products EH65 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Subaru Robin Power Products EH65 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Subaru Robin Power Products EH65 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Subaru Robin Power Products EH65 you will learn all the available features of the product, as well as information on its operation. The information that you get Subaru Robin Power Products EH65 will certainly help you make a decision on the purchase.
If you already are a holder of Subaru Robin Power Products EH65, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Subaru Robin Power Products EH65.
However, one of the most important roles played by the user manual is to help in solving problems with Subaru Robin Power Products EH65. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Subaru Robin Power Products EH65 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
