Instruction/ maintenance manual of the product SI SERIES Studer Innotec
Go to page of 10
STUDER INNOTEC SI User manual SI V3.0 E Sinewave inverter SI SERIES User's and Installer's Handbook STUDER INNOTEC Rue des Casernes 57 CH-1950 Sion Tel : ++41 (0)27 205 60 80 Fax: ++41 (0)27 205 60 88 info@studer-innotec.com www.studer-innotec.
STUDER INNOTEC SI User manual SI V3.0 E 2 Summary INTRODUCTION ................................................................................................................... ............. 3 NOTE ...................................................
STUDER INNOTEC SI User manual SI V3.0 E 3 Introduction The SI sinewave inverters have been designed to meet industrial and domestic needs. They satisfy the highest demands of comfort, safety and reliability. Any device designed for the public electrical network of 230V / 50 Hz can be connected to them.
STUDER INNOTEC SI User manual SI V3.0 E 4 Assembly Location The place where the inverter is to be mounted should meet the following requirements : Out of reach of non authorised persons. In a dry place with no condensation. No inflammable material in the same room.
STUDER INNOTEC SI User manual SI V3.0 E 5 Adjustments (Not automatic with Twinpower version) Standby Level (1) The activation of the inverter, when working in automatic mode, is dictated by the detection of a load. With this function, it is possible to adjust the minimum load detected between 0,3 and 20 Watts.
STUDER INNOTEC SI User manual SI V3.0 E 6 Options: Alarm contact A contact with no potential (0,5A - 60V) is available (12). It warns the user (alarm or control system) when the inverter has been stopped due to a failure or is out of use. It is closed when the inverter is working.
STUDER INNOTEC SI User manual SI V3.0 E 7 Description and wiring diagram.
STUDER INNOTEC SI User manual SI V3.0 E Wiring diagram for SI 600 - 800 S (Solar charge regulator).
STUDER INNOTEC SI User manual SI V3.0 E 9 Option SI performance 3-phased Three SI inverters can be connected together to build a 3-phased grid. They have to be equipped with the PE option. Working Two ways of working are possible with the SI performance : 1) Working alone One SI inverter can be used alone.
STUDER INNOTEC SI User manual SI V3.0 E 10 Technical data Model SI 612 624 648 812 824 1212 1224 1248 1624 2324 2348 3324 3548 Input voltage (Unom) [V] 12/ 24/48 12/24 12/24/48 24 24V/48 24 48 Nominal power [W] 600 800 1200 1600 2300 3300 3500 « Standby » current [mA] Power « ON » no load [W] 25/21/10 2.
An important point after buying a device Studer Innotec SI SERIES (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Studer Innotec SI SERIES yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Studer Innotec SI SERIES - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Studer Innotec SI SERIES you will learn all the available features of the product, as well as information on its operation. The information that you get Studer Innotec SI SERIES will certainly help you make a decision on the purchase.
If you already are a holder of Studer Innotec SI SERIES, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Studer Innotec SI SERIES.
However, one of the most important roles played by the user manual is to help in solving problems with Studer Innotec SI SERIES. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Studer Innotec SI SERIES along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
