Instruction/ maintenance manual of the product RCC130H Stow
Go to page of 60
OPERATION AND PARTS MANUAL STOW CONSTRUCTION EQUIPMENT A DIVISION OF MULTIQUIP INC . POST OFFICE BOX 6254 CARSON, CA 90749 310-537-3700 • 888-252-STOW [888-252- 7869] FAX: 310-537-1986 • FAX: 800-556-1986 E-MAIL: stow@mul tiquip.com • WWW: stowmfg.
.
TABLE OF CONTENTS RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 3 STOW CRACK SAW MODEL RCC130H Table Of Contents .............................................................................................................. .....
TABLE OF CONTENTS RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 4 Component Parts Drawings Operator Handl e Asse mbly....................................................................................................... ........
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 5 NOTE PAGE.
PARTS ORDERING PROCEDURES RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 6 When ordering parts, please supply the following information: Dealer account number Dealer name .
NOTICE TO OPERATORS RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 7 IF YOU CAN NOT READ OR DO NOT FULLY UNDERSTAND THE CONTENTS OF THIS MANUAL, PLEASE CONTACT THE FACT ORY FOR PROPER ASSISTANCE BEFORE ATTEMPTING TO OPERATE THIS PRODUCT.
NOTICE TO OPERATORS RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 8 The concept of frame mounted type Crack Saws has been successfully utilized for many years as a practical solution to many types of random crack sawi ng requirements.
OPERATOR INSTRUCTIONAL DATA SHEET RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 9 The following undersigned operators of the RCC130H CRACK SAW described and/or pertaining to this.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 10 SAFETY PRECAUTIONS THE FOLLOWING SAFETY PRECAUTIONS PROVIDE SOME COMMON SENSE GUIDES TO PROMOTE SAFETY AND EFFICIENCY WITH THE CRACK SAW.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 11 SAFETY PRECAUTIONS 6) Prolonged use of the CRACK SAW (or other, similar machines) exposes the operator to vibrations which may produce Whitefinger Disease (Raynaud's Phenomenon).
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 12 SAFETY PRECAUTIONS OPERATION. 1) Give complete and undivided attention to the job at hand. Do not chew gum, smoke and/or use smokeless tobacco while ut ilizing the Crack Saw. Do not attempt to eat and/or drink while utilizing the Crack Saw.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 13 SAFETY PRECAUTIONS vehicle, with greater horsepower and less mobility), method and/or process be utilized to properly complete the job with the degree of efficiency and safety required.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 14 ASSEMBLY INSTRUCTIONS/OPERATIONS Assembly The RCC130H Crack Saw is shipped from the factory secured on a specially designed wooden pallet and protected from external damage by a corrugated carton or wood crate.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 15 ASSEMBLY INSTRUCTIONS/OPERATIONS 1) Determine the location of the fuel tank filler cap. 2) Carefully clean the filler cap and surrounding area to insure that no dirt or debris falls into the fuel tank.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 16 ASSEMBLY INSTRUCTIONS/OPERATIONS DANGER IMPROPER USE OF A DIAMOND BLADE WITH THE CRACK SAW CAN RESULT IN PROPERTY DAMAGE AND/OR PERSONAL INJURY.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 17 ASSEMBLY INSTRUCTIONS/OPERATIONS the cut and letting it cool by rotating in the air for 15 to 20 seconds after every one minute of cutting. 13) Do not force the tool into the material to be cut.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 18 ASSEMBLY INSTRUCTIONS/OPERATIONS FIGURE 1 3) Position the quick change height lever over center to its rear most (up) position.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 19 ASSEMBLY INSTRUCTIONS/OPERATIONS while following a random crack. Determine the correct rotation orientation for the diamond blade and install it on the arbor shaft.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 20 ASSEMBLY INSTRUCTIONS/OPERATIONS PROPER QUANTITY OF PERSONNEL IN PROPER PHYSICAL CONDITION. The integral lifting bail device(s) can be used to facilitate lifting by a mechanical device incorporating a chain and suitable attachment device.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 21 ASSEMBLY INSTRUCTIONS/OPERATIONS 4) Refer to the material supplied by the engine manufacturer for the corre ct starting, operation and stopping procedures.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 22 ASSEMBLY INSTRUCTIONS/OPERATIONS PROPERTY DAMAGE AND/OR PERSONAL INJURY. EXCESSIVE LEVELS OF CARBON MONOXIDE CAN CAUSE DEATH. 1) The Crack Saw is of a downcut type design as viewed by the operator.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 23 ASSEMBLY INSTRUCTIONS/OPERATIONS 5) Turn the height adjustment lever clockwise to lower the blade into the crack until the desired sawing depth is achieved. Each full turn of the crank lever will raise/lower the blade approximately 1/16 inch.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 24 ASSEMBLY INSTRUCTIONS/OPERATIONS FIGURE 25 The amount and direction of forces to apply to the operator handle are governed by, but not necessarily limited to the following factors: a) Average Random Crack Width.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 25 ASSEMBLY INSTRUCTIONS/OPERATIONS 11) The sawing process on many work surface materials can produce sparks, dust and other foreign particle contamination.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 26 ASSEMBLY INSTRUCTIONS/OPERATIONS of the work surface when deployed to its maximum up position.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 27 ASSEMBLY INSTRUCTIONS/OPERATIONS A BLADE OF PROPER DIMENSIONS IS BEING UTILIZED. IF THERE ARE ANY QUESTION REGARDING PROPER BL ADE DIMENSIONS FOR USE WITH THE CRACK SAW, CONTACT THE CUSTOMER SERVICE DEPARTMENT FOR SPECIFIC INFORMATION.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 28 ASSEMBLY INSTRUCTIONS/OPERATIONS FIGURE 33 DANGER IMPROPER SAWING PROCEDURES FOR ANY SPECIFIC RANDOM CRACK CAN SUBSTANTIALLY REDUCE OPERATOR CONTROL, OVERALL PRODUCTIVITY AND CAUSE SEVERE DIAMOND BLADE DAMAGE, RESULTING IN PROPERTY DAMAGE AND/OR PERSONAL INJURY.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 29 ASSEMBLY INSTRUCTIONS/OPERATIONS STOPPING THE RCC130H SERIES GASOLINE POWERED CRACK SAWS. 1) Position the quick change height lever over center to its rear most (up) position. 2) Stop the Crack Saw by moving the engine throttle control lever to the idle speed position.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 30 ASSEMBLY INSTRUCTIONS/OPERATIONS e) Fatigue or alligator. Over time, as a pavement surface ages, it becomes more rigid and has less ability to tolerate vertical load deflections.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 31 MAINTENANCE/SERVICE Maintenance/Service PREVENTATIVE MAINTENANCE CHECK LIST. The normal operation of the Crack Saw produces extreme dirt and dust, along with levels of random vibration.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 32 MAINTENANCE/SERVICE FIGURE 35 5) Belt alignment is che cked with the straightedge. Place the straightedge squarely against the arbor shaft pulley. Properly aligned pulleys should also place the straightedge squarely against the engine/motor pulley.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 33 MAINTENANCE/SERVICE CAUTION Observe all applicable safety precautions for the solvent. 3) Remove the belt guard from the main frame. Clean the inside of the belt guard with an appropriate solvent.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 34 MAINTENANCE/SERVICE c) If the belt tension and alignment are within specifications, torque t he engine/electric motor attachment capscrews to 35 ft lbs (47 N.m). d) Recheck V-belt tension and alignment.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 35 MAINTENANCE/SERVICE FIGURE 40 FIGURE 41 CAUTION Exercise extreme caution when pressing the hub body from the arbor shaft/bearing block assembly. Improper activities can result in the components striking body parts, resulting in property damage and/or personal injury.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 36 MAINTENANCE/SERVICE FIGURE 44. FIGURE 45 11) Clean the bearing journal areas of the arbor shaft with an appropriate solvent. Apply a suitable amount of anaerobic adhesive/ sealant to the bearing journal area located near the snap ring groove.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 37 MAINTENANCE/SERVICE CAUTION Wear safety glasses and other appropriate safety apparel when removing the snap ring or performing any work with an arbor press. Caution all onlookers about the possibility of flying debris and personal injury.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 38 MAINTENANCE/SERVICE ENGINE SERVICE. RCC130H Crack Saw. Consult the material supplied by the engine manufacturer for specific serv.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 39 TROUBLESHOOTING Troubleshooting ENGINE FAILS TO START Ignition switch in OFF or cut off position. Place switch in the ON position or move throttle control lever to the ignition operational position.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 40 TROUBLESHOOTING periodically with an electronic tachometer to ensure proper operational speed for the blade. UNEVEN SEGMENT WEAR a) If wet sawing, insufficient water flow to one side of the blade which effectively reduces the side clearance.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 41 TROUBLESHOOTING BLADE WOBBLES a) Worn machine components. Determine that machine components including bearings, belts and the arbor shaft are not excessively worn and requiring replacement.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 42 STORAGE Storage Proper procedure for long term storage of the Crack Saw will protect it against the effects of corrosion and damage.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 43 SPECIFICATIONS Specifications FRAME. STRUCTURE............................................................................ Unitized, Welded Steel Plate DRIVE REDUCTION SYST EM ....
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 44 EXPLANATION OF CODE IN REMARKS COLUMN How to read the marks and remarks used in this parts book. Section 1: Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serial number range (inclusive) where a particular part is used.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 45 SUGGESTED SPARE PARTS RCC130H CRACK SAW 1 TO 3 UNITS Gasoline Engine Model Honda GX390 Qty. P/N Description 6 ............. 29022-014 ..............V-BELT 3 ............. 17210ZE3505 .
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 46 OPERATOR HANDLE ASSY. OPERATOR HANDLE ASSY..
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 47 OPERATOR HANDLE ASSY. OPERATOR HANDLE ASSY. NO. PART NO. PART NAME QTY. REMARKS 1 29022-017 HANDLE, OPERATOR 1 2 29022-018 CRANK .
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 48 DRIVETRAIN AND ENGINE MOUNTING ASSY. DRIVETRAIN AND ENGINE MOUNTING ASSY..
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 49 DRIVETRAIN AND ENGINE MOUNTING ASSY. DRIVETRAIN AND ENGINE MOUNTING ASSY. NO. PART NO.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 50 FRAME ASSY. FRAME ASSY.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 51 FRAME ASSY. FRAME ASSY NO. PART NO. PART NAME QTY. REMARKS 1 29022-001 FRAME, MAIN 1 2 29018-046 WHEEL 2 3 07030-012 WASHER, FLAT.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 52 DUST VACUUM PORT ASSY. DUST/VACUUM PORT ASSY.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 53 DUST VACUUM PORT ASSY. DUST/VACUUM PORT ASSY NO. PART NO. PART NAME QTY. REMARKS 1 29022-028 SHROUD, VACUUM 1 2 29022-029 HOSE, V.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 54 WET CUTTING KIT ASSY. WET CUTTING KIT ASSY.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 55 WET CUTTING KIT ASSY. WET CUTTING KIT ASSY NO. PART NO. PART NAME QTY. REMARKS 1 29020-007 VALVE 1 2 29022-030 BLOCK, MANIFOLD 1 .
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 56 DECALS DECALS.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 57 DECALS DECALS NO. PART NO. PART NAME QTY. REMARKS 1 29020-045 DECAL, WARNING 1 2 29022-033 DECAL, OPERATION 1 3 29020-048 DECAL, .
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 58 Effective : July 15, 2003 TERMS AND CONDITION OF SALE— PARTS PAYMENT TERMS T erms of payment for unit sales are 2% 15 days net 30 days from date of invoice unless otherwise specifically stated on our invoice.
RCC130H-CRACK SAW OPERATION AND PARTS MANUAL REV #1 (11/18/04) PAGE 59 NOTE PAGE.
OPERATION AND PARTS MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON- HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 SER.
An important point after buying a device Stow RCC130H (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Stow RCC130H yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Stow RCC130H - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Stow RCC130H you will learn all the available features of the product, as well as information on its operation. The information that you get Stow RCC130H will certainly help you make a decision on the purchase.
If you already are a holder of Stow RCC130H, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Stow RCC130H.
However, one of the most important roles played by the user manual is to help in solving problems with Stow RCC130H. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Stow RCC130H along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center