Instruction/ maintenance manual of the product SPL31A-N Stanley Black & Decker
Go to page of 16
© 2013 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 72925 7/2014 V er . 8 USER MANUAL Safety and Operation SPL31A SPL31A-N SPL31A-S HYDRAULIC SPIKE PULLER.
2 ► SPL31 User Manual NOTES.
SPL31 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer .
4 ► SPL31 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
SPL31 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs.
6 ► SPL31 User Manual SAFETY T AG (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL.
SPL31 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
8 ► SPL31 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility B.
SPL31 User Manual ◄ 9 Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min.
10 ► SPL31 User Manual CHECK HYDRAULIC POWER SOURCE 1. Using a calibrated owmeter and pressure gauge, check that the hydraulic power source develops a ow of 5-10.5 gpm/15-40 lpm at 2000 psi/140 bar . 2. Make certain the hydraulic power source is equipped with a relief valve set to a max of 2500 psi/172 bar .
SPL31 User Manual ◄ 1 1 Problem Cause Solution Spike puller does not cycle. Hydraulic power source not functioning correctly . Check power source for proper ow and pressure (5-10 gpm/19-34 lpm, 2500 psi/172 bar . Coupler or hoses blocked. Remove obstruction.
12 ► SPL31 User Manual Pulling Force...........................................................................................................................................16,647 lbs / 7550 kg- Pressure ...........................................
SPL31 User Manual ◄ 13 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 17 ITEM P ART NO. QTY DESCRIPTION 1 1 O-RING* (P ART OF SEAL KIT) 2 1 O-RING* (P ART OF SEAL KIT) 3 03009 ROLL PIN (SPL31A-S, SPL31A-N ONL.
14 ► SPL31 User Manual 2 3 4 5 7 8 9 10 11 18 19 20 22 23 24 27 28 29 30 31 32 33 34 36 37 38 39 40 43 44 45 46 24 46 4 10 55 49 50 FOR P ARTS TO HANDLE ASSEMBL Y SEE P AGE 13 SEE P AGE 6 FOR DECAL .
SPL31 User Manual ◄ 15 * DENOTES P ART IN SEAL KIT SEAL KIT 73042 ITEM P/N. QTY . DESCRIPTION 2 00596 4 CAPSCREW 3 1 O-RING* (P ART OF SEAL KIT) 4 00664 2 RET AINING RING 5 1 O-RING* (P ART OF SEAL KIT) 7 03972 1 COUPLER,FEMALE 3/8NPT FL.F ACE SET P/N-03971 (SP- L31A AND SPL31A-S ONL Y) 47436 1 COUPLER,FEMALE 3/8NPT FL.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
An important point after buying a device Stanley Black & Decker SPL31A-N (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Stanley Black & Decker SPL31A-N yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Stanley Black & Decker SPL31A-N - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Stanley Black & Decker SPL31A-N you will learn all the available features of the product, as well as information on its operation. The information that you get Stanley Black & Decker SPL31A-N will certainly help you make a decision on the purchase.
If you already are a holder of Stanley Black & Decker SPL31A-N, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Stanley Black & Decker SPL31A-N.
However, one of the most important roles played by the user manual is to help in solving problems with Stanley Black & Decker SPL31A-N. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Stanley Black & Decker SPL31A-N along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
