Instruction/ maintenance manual of the product CS25/28 Stanley Black & Decker
Go to page of 22
© 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 66205 8/2014 V er . 9 USER MANUAL Safety , Operation and Maintenance CS25/28 HYDRAULIC POLE CHAIN SA W.
2 ► CS25/28 User Manual DECLARATION OF CONF ORMI TY ÜBEREINSTIMM UNGS - ERKLARUNG DECLARATION DE CONFOR MITE CEE DECLARACION DE CONFO RMIDAD DICHIARAZIONE DI CONFORM ITA Hydraulic Tools _______ ___.
CS25/28 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an au- thorized and certied dealer .
4 ► CS25/28 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
CS25/28 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose.
6 ► CS25/28 User Manual POLE CHAIN SA W SPECIFIC SAFETY PRECAUTIONS • Do not rely exclusively upon the safety devices built into the saw . As a pole saw user , several steps must be taken to keep your cutting jobs free from accident or injury . • With basic understanding of kickback, you can re- duce or eliminate the element of surprise.
CS25/28 User Manual ◄ 7 The following guidelines must be followed to prevent accidental contact with overhead electrical conductors and/or communication wires and cables.
8 ► CS25/28 User Manual T able 2 – Minimum approach distances to energized conductors for persons other than qualied line- clearance arborists and qualied line-clearance ar - borist trainees. Nominal V oltage kV phase-to-phase 1) Distance ft-in m 0.
CS25/28 User Manual ◄ 9 SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL.
10 ► CS25/28 User Manual The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
CS25/28 User Manual ◄ 1 1 Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utili.
12 ► CS25/28 User Manual Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min.
CS25/28 User Manual ◄ 13 screw located in the top of the valve spool fully in (clock- wise) until it bottoms. TO DISABLE DUAL SPOOL OPERA TION AND CONVERT TO OC ONL Y OPERA TION T urn the selector screw located in the top of the valve spool fully out (counter-clockwise) until it hits the stop.
14 ► CS25/28 User Manual 4. WARNING W atch for falling limbs. Make a diagonal cut down to meet the horizontal cut and remove the wood from the notch. FELLING OR BACK CUT 5. The felling or back cut is made on the side opposite and at least 2 inches above the horizontal undercut (the felling cut is made higher as the size of the tree increases).
CS25/28 User Manual ◄ 15 PRUNING & TRIMMING 1. Observe all safety precautions. 2. Use both hands. Keep a rm grip. 3. Be alert for kickback. Do not allow the tip of the bar to touch anything while the chain is in motion. Figure 3. Crosscutting Logs/Limbs with Pressure on Bottom 4.
16 ► CS25/28 User Manual CHAIN TENSION ADJUSTMENT 1. Observe all safety precautions. 2. When the chain appears loose, lubricate it well and let it cool for a few minutes to allow for contraction of the chain. Disconnect the pole chain saw from its hydraulic power source.
CS25/28 User Manual ◄ 17 • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the OFF position when coupling or uncoupling hydraulic tools. Failure to do so may result in damage to the quick couples and cause overheating of the hydrau- lic system.
18 ► CS25/28 User Manual If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the pole chain saw , always make sure the hydraulic power source is supply- ing the correct hydraulic ow and pressure as listed in the table.
CS25/28 User Manual ◄ 19 Capacity CS25 and CS28 .................................................................................... 12 and 15 inch/30 and 38 cm Cut Lengths Weight (w/o Bar and Chain) .................................................
20 ► CS25/28 User Manual T o order complete motor assembly see “Note” on parts list (Page 21). CS25 / CS28 P ARTS ILLUSTRA TION.
CS25/28 User Manual ◄ 21 ITEM P ART NO. QTY DESCRIPTION 1 19212 1 CAPSCREW 2 65834 1 CHAIN GUARD 3 07631 2 NUT 4 08348 1 SA W CHAIN – 12 INCH 07641 1 SA W CHAIN – 15 INCH 5 66577 1 CHAIN GUIDE P.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
An important point after buying a device Stanley Black & Decker CS25/28 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Stanley Black & Decker CS25/28 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Stanley Black & Decker CS25/28 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Stanley Black & Decker CS25/28 you will learn all the available features of the product, as well as information on its operation. The information that you get Stanley Black & Decker CS25/28 will certainly help you make a decision on the purchase.
If you already are a holder of Stanley Black & Decker CS25/28, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Stanley Black & Decker CS25/28.
However, one of the most important roles played by the user manual is to help in solving problems with Stanley Black & Decker CS25/28. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Stanley Black & Decker CS25/28 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
