Instruction/ maintenance manual of the product CS05 Stanley Black & Decker
Go to page of 26
© 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 66864 7/2014 V er . 8 USER MANUAL Safety , Operation and Maintenance CS05/CS06 HYDRAULIC CHAIN SA W.
.
CS05/CS06 User Manual ◄ 3 WARNING SERIOUS INJUR Y OR DEA TH COULD RESUL T FROM THE IMPROPER REP AIR OR SERVICE OF THIS T OOL. REP AIRS AND / OR SERVICE T O THIS TOOL MUST ONL Y BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. SERVICING: This manual contains safety , operation, and routine maintenance instructions.
4 ► CS05/CS06 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte - nance personnel.
CS05/CS06 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose.
6 ► CS05/CS06 User Manual – maintenance instructions for the saw chain. – Only use replacement bars and chains specied by Stanley Hydraulic T ools. Chains must meet the requirements of ANSI B175.1 for low kick - back performance. • Always be well rested and mentally alert before op - erating the chain saw .
CS05/CS06 User Manual ◄ 7 The following guidelines must be followed to prevent accidental contact with overhead electrical conductors and/or communication wires and cables.
8 ► CS05/CS06 User Manual T able 2 – Minimum approach distances to energized conductors for persons other than qualied line-clearance arborists and qualied line-clearance ar - borist trainees. Nominal V oltage kV phase-to-phase 1 Distance ft-in m 0.
CS05/CS06 User Manual ◄ 9 28323 CE Decal (CE Models Only) 28409 Composite Decal (CE Models Only) D 30 LPM @ 138 BA R EHTMA CA TEGORY 1 1207 Circuit T ype D Decal (CE Models Only) Fa ilure to use hyd.
10 ► CS05/CS06 User Manual The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy - draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
CS05/CS06 User Manual ◄ 1 1 Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Uti.
12 ► CS05/CS06 User Manual Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min.
CS05/CS06 User Manual ◄ 13 OPERA TING PROCEDURES The following are general wood cut ting procedures and techniques. Dif ferences in the terrain, vegetation, and type of wood will make this infor mation more or less val - id for particu lar areas.
14 ► CS05/CS06 User Manual FELLING OR BACK CUT 4. The felling or back cut is made on the side opposite and at least 2 inches above the hori zontal undercut (the felling cut is made higher as the size of the tree increases). Place the saw so the hand guard is close to the tree trunk and the bucking cleat is dug in.
CS05/CS06 User Manual ◄ 15 Figure 4. Crosscutting Logs Larger than Bar Length With Pressure on T op LOGS WITH PRESSURE ON TOP (FIGURE 3) 1. Observe all safety precautions. 2. Begin with an upper cut, down from the top. Do not cut too deeply . A cut of about 1/3 of the log diameter is enough.
16 ► CS05/CS06 User Manual Figure 6. Crosscutting Thick Logs with Pressure on Bottom LOGS/LIMBS WITH PRESSURE ON BOTTOM (FIGURE 5) 1. Observe all safety precautions. 2. Begin with a bottom cut. The depth of the cut should be about 1/3 of the log diameter .
CS05/CS06 User Manual ◄ 17 PRUNING AND DEBRANCHING 1. Observe all safety precautions. 2. Use both hands. Keep a rm grip. 3. Be alert for kickback. Do not allow the tip of the bar to touch anything while the chain is in motion. 4. Do not cut overhead.
18 ► CS05/CS06 User Manual • Make sure all couplers are wiped clean before con - nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydrau - lic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hy - draulic system.
CS05/CS06 User Manual ◄ 19 If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the saw , always make sure the hydraulic power source is supplying the correct hydraulic ow and pressure to the saw as listed in the table.
20 ► CS05/CS06 User Manual Capacity CS05 ..................................................................................................... 12 and 15 inch/30 and 38 cm Cut Lengths CS06 .............................................................
CS05/CS06 User Manual ◄ 21 CS05/CS06 P ARTS ILLUSTRA TION.
22 ► CS05/CS06 User Manual ITEM NO. P ART NO. QTY DESCRIPTION 1 00753 09622 8 CAPSCREW CAPSCREW U/W MODEL 2 07636 08202 1 NAME T AG—CS06 NAME T AG—CS05 3 28323 1 CE DECAL (CE ONL Y) 4 07652 1 RE.
CS05/CS06 User Manual ◄ 23 ITEM NO. P ART NO. QTY DESCRIPTION 71 07610 1 SPRING 72 00190 1 ROLL PIN 73 10537 1 KEEPER 74 07625 1 PLUG BUTTON 75 03786 1 GPM STICKER (7–9 GPM) 03782 1 GPM STICKER (4.
24 ► CS05/06 User Manual For underwater hydraulic tools the applications are broken down into four quadrants depending on type of tool and method of operation. The types of tools are percussive and rotational, each with different characteristics allowing for dif - ferent depth operation.
CS05/06 User Manual ◄ 25 NOTES.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
An important point after buying a device Stanley Black & Decker CS05 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Stanley Black & Decker CS05 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Stanley Black & Decker CS05 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Stanley Black & Decker CS05 you will learn all the available features of the product, as well as information on its operation. The information that you get Stanley Black & Decker CS05 will certainly help you make a decision on the purchase.
If you already are a holder of Stanley Black & Decker CS05, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Stanley Black & Decker CS05.
However, one of the most important roles played by the user manual is to help in solving problems with Stanley Black & Decker CS05. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Stanley Black & Decker CS05 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
