Instruction/ maintenance manual of the product cp-2010 Spracht
Go to page of 20
V oice Center ™ Conference Phone CP-2010 model series User's Manual.
.
T able of Contents - V oice Center User’s Manual Introduction and Quick Start Guide Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction Thank you for choosing the V oice Center Conference Phone, a high per formance audio conferencing system. Its features include: • Full duplex communication – the V oice Center’ s digital speech processing enables simultaneous two- way communication.
3 Quick Start Guide 3. Analog or Digital T elephone System? Caution: if the V oice Center is connected to a digital telephone system using the Analog T elephone System Inter face, it will not operate correctly , and may cause damage to the A T -101 Analog Interface and cause it to over heat.
Analog T elephone System Setup with Analog T elephone System If you are connecting the V oice Center Conference Phone to an analog telephone system, follow the instructions below .
W all Mounting of Analog Interface (Optional) • Install the two mounting screws supplied with the Analog Interface in the wall. Leave approximately 3/16 in. (0.5 cm) between screw head and wall. • Place the Analog Interface over the mounting screws and slide it down to fix it in position.
Keypad Functions with Analog Phone System ON/OFF Pressing the ON/OFF key turns the Conference Phone on to obtain a dial tone, or turns it off to terminate a call.
Conference Phone Operation with Analog Phone System Answering a call When the Conference Phone rings, press the ON/OFF key to answer the call. The green LED illuminates to indicate the Conference Phone is on.
Digital T elephone System Setup of Conference Phone with Digital Phone System Note: The DT -102 Digital T elephone System Inter face is required for use of the Voice Center Conference Phone with a digital phone system. Follow the steps below to set up the system.
4. Use Digital Inter face’s 4-position switch to adjust audio level by making a test call. • Lift digital telephone handset from its cradle, then press Conference Phone’ s “On/Off” key .
Keypad Functions with Digital Phone System ON/OFF Pressing the ON/OFF key turns the Conference Phone on to connect a call, or turns it off to ter- minate the Conference Phone conversation. The green LED just above the ON/OFF key illumi- nates when the Conference Phone is on.
Conference Phone Operation with Digital Phone System Answering a call 1. When the phone rings, pick up the digital telephone handset to accept the call.
General Setup T ips T ips for Obtaining Optimal Acoustic Performance •T o minimize echoes, place the Conference Phone at the center of the room, or at least away from walls (at least 20 inches/0.5 m from any wall). • It is impor tant to place the Conference Phone on the sur face where it will be used before applying power .
General Installation of External Microphones (Optional) The V oice Center Conference Phone has 3 built-in microphones for complete 360° coverage in areas up to 10 x 15 ft (3 x 4.5 m). The V oice Center Conference Phone has RJ-22 input jacks for two external microphones to extend coverage in larger areas and to allow for irregular layouts.
Specifications Conference Phone Controls and Interface Switches Microphone switch to turn on 1, T one/pulse switch to select 2, or all 3 built-in microphones telephone dialing mode LED indication ligh.
Spracht Limited W arranty Policy Spracht warrants it products against defects or malfunctions in material and workmanship under normal use and ser vice, with the exceptions stated below . This warranty lasts for one year from the original date of purchase.
Federal Communications Commission Statement Note: The V oice Center Conference Phone equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Par t 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
.
SPRACHT T el: 650-318-8061 Fax: 650-318-8060 2672 Bayshore Parkway , Bldg 900 Mountain View , CA 94043 USA www .spracht.com © 2001 Spracht Spracht and V oice Center are trademarks of ODI.
An important point after buying a device Spracht cp-2010 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Spracht cp-2010 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Spracht cp-2010 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Spracht cp-2010 you will learn all the available features of the product, as well as information on its operation. The information that you get Spracht cp-2010 will certainly help you make a decision on the purchase.
If you already are a holder of Spracht cp-2010, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Spracht cp-2010.
However, one of the most important roles played by the user manual is to help in solving problems with Spracht cp-2010. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Spracht cp-2010 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
