
©1998 by Sony Corporation SLV-E780EE
3-861-928-11 (1)

To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Mains lead must only be changed at qualified service shop.
Precautions
This VCR is designed to record using the PAL (B/G or D/K) or MESECAM (B/G or D/K) colour system and play back using the PAL (B/ G or D/K), MESECAM (B/G or D/K), and NTSC 4.43 colour systems. Recording of video sources based on other colour systems cannot be guaranteed.


Unpacking
Check that you have received the following items with the VCR:

Setting up the remote commander

Insert two R6 (size AA) batteries by matching the + and – on the batteries to the diagram inside the battery compartment.
Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position.
You can use this remote commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV.

Remote sensor · continued


Turn the TV into standby or active mode
Select an input source of the TV either from aerial in or from line in
Select the programme position of the TV
Programme number buttons PROG +/–
Adjust the volume of the TV

Call up on-screen display
Operate TV menu options
MENU >/./?//, OK
Switch to/from wide mode of a Sony wide TV.

Connecting the VCR

1 Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the VCR.

2 Connect AERIAL OUT of the VCR and the aerial input of your TV using the supplied aerial cable.
IN ENTREE
OUT SORTIE
3 Connect the mains lead to the mains.

This additional connection improves picture and sound quality. Connect the TV as shown below. Whenever you want to watch the VCR picture, press TV/VIDEO to display the VIDEO indicator in the display window.
To a TV that has a EURO-AV (Scart) connector If your TV has a EURO-AV (Scart) connector, connect your TV by using VMC-2121 EURO-AV cable as shown on the right.

VMC-2121 EURO-AV cable (not supplied)
To a TV that has LINE IN connector If your TV has LINE IN connector, connect your TV by using audio/video cable as shown on the right.

Audio/video cable (not supplied)
Note • When you connect the VCR and your TV only with an aerial cable, you have to set RF MODULATOR in the OPTIONS menu to ON (initial setting). If the TV is connected to the LINE-1 (TV) connector, setting RF MODULATOR in the OPTIONS menu to OFF is recommended. In the OFF position, only the signal from the aerial is output through the AERIAL OUT connector (see page 40).

Tuning your TV to the VCR
If you have connected the VCR to your TV using the EURO-AV cable, skip this step.
RF CHANNEL 1 Press ON/STANDBY to turn on the VCR.
2 Press RF CHANNEL on the VCR.
The factory-preset RF channel appears in the display window.
The VCR signal is output through this channel to the TV.
3 Turn on your TV and select a programme position for the VCR picture.
This programme position will now be referred to as the video channel. 4 Press RF CHANNEL.
The TV system appears in the display window.

5 Press PROGRAM +/– (repeatedly) to select the correct TV system. If you watch the system B/G, select “G.” If you watch the system D/K, select “K.”
6 Tune the TV to the same channel as that shown in the display window so that the picture on the right appears on the TV screen.
Refer to your TV manual for tuning instructions.
If the picture does not appear clearly, see “To obtain a clear picture from the VCR” below. 7 Press RF CHANNEL.
You have now tuned your TV to the VCR. Whenever you want to play a tape, set the TV to the video channel.
To check to see if the TV tuning is correct Set the TV to the video channel and press PROGRAM +/– on the VCR. If the TV screen changes to a different programme each time you press PROGRAM +/–, the TV tuning is correct.
To obtain a clear picture from the VCR If the picture does not appear clearly in step 6 above, go to step 7 to finish this procedure once. Then start again from step 2. After pressing RF CHANNEL in step 2, press PROGRAM +/– while the RF channel is displayed, so that another RF channel appears. Then tune the TV to the new RF channel until a clear picture appears.

Setting up the VCR with the Auto Set Up function
Before using the VCR for the first time, set up the VCR using the Auto Set Up function. With this function, you can set the TV channels guided by the sequence indicated on the TV screen.
AUTO SET UP
Hold down AUTO SET UP on the VCR for more than three seconds.
The VCR automatically turns on, and the ATP (Auto Tuner Preset) function starts searching for all of the receivable channels and presets them in numerical order (according to the TV system you selected in “Tuning your TV to the VCR”).
After the search is complete, the current time appears in the display window for any stations that transmit a time signal.
To cancel the Auto Set Up function Press AUTO SET UP.


You must set the time and date on the VCR to be able to use the timer recording features properly.

1 Press MENU, then press >/. to select SETTINGS and press OK.
2 Press >/. to select CLOCK, then press OK.

3 Press >/. to set the date.
continued

4 Press / to flash the month and set the month pressing >/..
PLAY
2 9 TU 8
SELECT SET END
: : :
5 Set the year, hour, and minutes in sequence, pressing / to flash the item to be set, and press >/. to select the digits.
PLAY
2 9 FR 8 1
The day of the week is set automatically.
: : :
6 Press / to start the clock.
PLAY
2 9 FR 8 1
SELECT SET END
: : :
7 Press OK.
OK


You can change the on-screen display language.
1 Press MENU, then press >/. to select SETTINGS and press OK.

2 Press >/. to select LANGUAGE and press OK.
3 Press >/./?// to move the dot ( r ) to the desired language, then press OK.


MENU
If some channels could not be preset using the Auto Set Up function, you can preset them manually.
1 Press MENU, then press >/. to select SETTINGS and press OK.

2 Press >/. to select TUNER and press OK.
NORMAL / CATV CHANNEL SET [ ] C [ ] NORM
3 Press >/./?// to move the cursor (”) to NORMAL/CATV, then select NORM.
NORMAL / CATV CHANNEL SET [ ] C [ ] NORM

4 Press >/. to move the cursor (”) to CHANNEL SET.
PROG10
PLAY
SYSTEM [ ] D / K
OK
NORMAL / CATV CHANNEL SET [ ] C [ ] NORM
SELECT SET
: :
5 Press PROG +/– to select the programme position.
SYSTEM [ ] D / K
NORMAL / CATV CHANNEL SET [ ] C [ ] NORM
SELECT SET
: :
6 Press ?// repeatedly until the channel you want is displayed.
The channels appear in the following order:
Channel number in the CHANNEL SET field
Channel Channel number in the CHANNEL SET field
2 E2 2 R1 3 E3 5 R6 4 E4 6 R7 5 E5 12 R12 6 E6 13 R2 7 E7 14 R3 8 E8 15 R4 9 E9 16 R5 10 E10 17 R8 11 E11 18 R9 12 E12 19 R10 21–69 E21–E69 20 R11 CATV 1–41 S1–S41 21–69 R21–R69 CATV 42–46 S01–S05
If you know the number of the channel you want, press the programme number buttons. For example, for channel 5, first press “0” and then press “5.”

7 If the TV sound is distorted or noisy, press >/./?// to move the cursor (”) to SYSTEM, then select B/G or D/K so that you get the better sound.
PROG 4
SYSTEM [ ] D / K
PLAY
NORMAL / CATV CHANNEL SET [ ] C [ ] NORM
AFT [ ] ON FINE TUNING
SELECT SET
: :
8 To allocate another channel to another programme position, repeat steps from 5 to 7. 9 Press OK.
OK
Disabling unwanted programme positions
After presetting channels, you can disable unused programme positions. The disabled positions will be skipped later when you press the PROG +/– buttons. 1 In step 6 above, press programme number button “0” twice to display the number “00” beside CHANNEL SET. 2 Press OK.
![Page 19 of the Sony SLV-E780EE user manual — AFT [ ] OFF FINE TUNING](/cdn/reader/c1/c1d247fbf286f182c17a9dd646267d3a3c914653e63f0eda0016893367072a4d/images/page-19.webp?w=400)
Normally, the Auto Fine Tuning (AFT) function automatically tunes in channels clearly. If, however, the picture is not clear, you may also use the manual tuning function. 1 Press PROG +/– or the programme number buttons to select the programme number for which you cannot obtain a clear picture. 2 Press MENU, then select SETTINGS and press OK. 3 Select TUNER, then press OK. 4 Select FINE TUNING.
The fine tuning meter appears.
SYSTEM [ ] D / K
NORMAL / CATV CHANNEL SET [ ] C [ ] NORM
–– –– –– –– SELECT SET
: :
5 Press ?// to get a clearer picture, then press OK.
Selected programme position


DISPLAY
COUNTER RESET
REPLAY
· PLAY P PAUSE )# FF p STOP 03 REW
1 Turn on your TV and set it to the video channel. 2 Insert a tape.
The VCR turns on and starts playing automatically if you insert a tape with its safety tab removed.
Basic Operations

3 Press · PLAY.
When the tape reaches the end, it will rewind automatically.
Additional tasks
P PAUSE
Resume play after pause
P PAUSE or · PLAY
)# FF during stop
03 REW during stop
To replay a recently watched scene You can immediately rewind and playback the scene you want to watch again.
During playback, press REPLAY up to four times. The VCR rewinds the tape about 10 seconds on the counter for each press of the button, and restarts playback.
To set the colour system If the playback picture has no colour, or streaks appear during playback, set the SYSTEM option in the VIDEO OPTIONS menu to conform to the system that the tape was recorded in (see page 40). (Normally set the option to AUTO.)
To play an NTSC-recorded tape Set NTSC PB at the rear of the VCR according to the colour system of your TV.
When your TV is
Set NTSC PB to
NTSC 4.43

To use the time counter At the point on the tape that you want to find later, press COUNTER RESET. The counter in the display window resets to “0:00:00.” Search for the point afterwards by referring to the counter.
To display the counter on the TV screen, press DISPLAY.


COUNTER/ REMAIN
TV/VIDEO
PROG +/–
INPUT SELECT
SP/LP
Basic Operations
1 Turn on your TV and set it to the video channel.
To record from a decoder, turn it on. 2 Insert a tape with its safety tab in place.

3 Press INPUT SELECT until a programme position number appears in the display window.
VIDEO SP
4 Press PROG +/– to select the programme position you want to record.
5 Press SP/LP to select the tape speed, SP or LP.
LP (Long Play) provides recording time twice as long as SP, however, SP (Standard Play) produces better picture and audio quality.

The recording indicator lights up red in the display window.
To stop recording Press p STOP.

To check the remaining time Press DISPLAY. With the display on, press COUNTER/REMAIN to check the remaining time. Each time you press COUNTER/REMAIN, the time counter and the remaining time appear alternately. The remaining time with the indicator also appears in the display window.
Time counter Remaining time
To correctly check the remaining time of the tape, set TAPE SELECT in the TAPE OPTIONS menu according to the tape type you use (see page 39).
To watch another TV programme while recording 1 Press TV/VIDEO on the remote commander to turn off the VIDEO indicator in the display window. 2 Select another programme position on the TV.
To save a recording To prevent accidental erasure, break off the safety tab as illustrated. To record on a tape again, cover the tab hole with adhesive tape.
Safety tab · continued · Basic Operations



You can preset up to eight programmes at a time.
MENU
Basic Operations
>/./?// OK p STOP

1 Press MENU and select TIMER, then press OK.
continued · Basic Operations

2 Set the date, programme position, start and stop times, and tape speed:
WE 2 1 . 9
DATE
PROG TODAY ––
TIME
PLAY
1 Press / to flash each item in turn. 2 Press >/. to set each item. To correct a setting, press ? to return to that setting and reset.
SP
SELECT SET OK
: : : OK
PLAY
OK
4 Press ON/STANDBY to turn off the VCR.
The indicator appears in the display window and the VCR stands by for recording.
To record from a decoder or other source, leave the connected equipment switched on.
To stop recording To stop the VCR while recording, press p STOP on the VCR.

Daily/weekly recording In step 2 above, press . to select the recording pattern. Each time you press ., the indication changes as shown below. Press > to change the indication in reverse order.
TODAY n SU-SA (Sunday to Saturday) n MO-SA (Monday to Saturday) n MO- FR (Monday to Friday) n SA (every Saturday) n MO (every Monday) n SU (every Sunday) n 1 month later n (dates count down) nTODAY
To record satellite broadcasts If you connect the satellite tuner and the VCR, you can record satellite programmes. 1 Turn on the satellite tuner. 2 On the satellite tuner, select the satellite programme for which you wish to make a timer setting. 3 Keep the satellite tuner turned on until the VCR finishes recording the satellite programme for which you have made a timer setting.
To use the VCR after setting the timer To use the VCR before a timer recording begins, just press ON/STANDBY. The indicator turns off and the VCR switches on. Remember to press ON/STANDBY to reset the VCR after using the VCR.
You can also do the following tasks while the VCR is recording:
continued · Basic Operations



During fast-forward, press and hold )# FF. During rewind, press and hold 03 REW.
During playback, press × 2.
Play at twice the normal speed
Play in slow motion
During playback, press & SLOW.
Play frame by frame
During pause, press )# FF or 03 REW. Press and hold )# FF or 03 REW to play one frame each second.
Rewind and start play
During stop, press · PLAY on the VCR while holding 03 REW down on the VCR.
Additional Operations · continued

To resume normal playback Press · PLAY.


After starting recording in the normal way, you can have the VCR stop recording automatically after a specified duration.
2 Press QUICK TIMER repeatedly to set the duration.
Each press advances the time in increments of 30 minutes.
The duration decreases minute by minute to 0:00, then the VCR stops recording and turns off automatically.
To extend the duration Press QUICK TIMER repeatedly to set to the new duration.
To stop recording To stop the VCR while recording, press p STOP.
You can set the quick timer and start recording during stop mode by pressing QUICK TIMER. To set the programme position, you can use the PROG +/– or INPUT SELECT buttons. Press QUICK TIMER repeatedly to set the recording duration. The recording will start automatically.


CLEAR
Before you start… • Turn on your TV and set it to the video channel.
> / . / ? / / OK
1 Press ON/STANDBY to turn on the VCR. 2 Press MENU and select LIST, then press OK:
WE 2 1 . 9
DATE
PROG TIME 1 5 900 2000
LP 2 6 930 000 1 SP 44 500 530 LP 1 000 100 LP
3 0
2 2 300 000 SP MO MO
SA – – –FR
VPS PDC L L
SA
SU 2 1 7 212 2000 LP – –– ––– ––– –
Additional Operations 34

3 Press >/. to select the setting you want to change or cancel, then press OK.
WE 2 1 . 9
DATE
PROG TODAY 35
TIME 19 : 00 20 : 00
The selected setting appears in the TIMER menu.
LP
SELECT SET OK
: : : OK
4 To change the setting, press ?// to flash the item you want to change, and press >/. to reset it.
To cancel the setting, press CLEAR. 5 Press OK.
If any settings remain, turn off the VCR to return to recording standby.
When the timer settings overlap The programme that starts first has priority and the second programme starts recording only after the first programme has finished. If the programmes start at the same time, the programme listed first in the menu has priority.
Will be cut off
about 20 seconds will be cut off

Press AUDIO MONITOR to select the sound you want.
Stereo/main and sub (left and right channels)
STEREO
STEREO
R
STEREO
How sound is recorded on a video tape
The VCR records sound onto two separate tracks. Hi-fi audio is recorded onto the main track along with the picture. Monaural sound is recorded onto the normal audio track along the edge of the tape.
Usually mixed left/right channels Normal audio track (monaural)
Hi-fi audio track (main track)
Stereo sound (left/right channels)
Main (left channel) Sub (right channel)

Although the VCR automatically adjusts the tracking when playing a tape (the indicator flashes in the display window, then goes off), distortion may occur if the tape was recorded in poor condition. In this case, manually adjust the tracking.
During playback, press TRACKING +/– on the VCR to display the tracking meter. The distortion should disappear as you press one of the two buttons (the indicator lights up). To resume automatic tracking adjustments, eject the tape and reinsert it.
About Optimum Picture Control (OPC)
Optimum Picture Control (OPC) automatically improves recording and playback quality by adjusting the VCR to the condition of the video heads and tape. To maintain better picture quality, we recommend that you set OPC to ON in the VIDEO OPTIONS menu (with the OPC indicator in the display window lit). For details, see page 40.
OPC EDIT [ OFF [ ON
SYSTEM [ AUTO ]
SELECT SET
: :
OPC playback The OPC function automatically works on all types of tapes, including rental tapes and tapes that were not recorded with OPC.
OPC recording Whenever you insert a tape and start recording for the first time, the VCR adjusts to the tape using the OPC function (the OPC indicator flashes rapidly). This adjustment is retained until the tape is ejected.
To deactivate the OPC Set OPC to OFF in the VIDEO OPTIONS menu. The OPC indicator in the display window goes off.
Tracking meter · ] ] · continued


1 Press MENU, then select SETTINGS. 2 Select OPTIONS.
TAPE OPTIONS VIDEO OPTIONS
AUDIO MIX [ ] OFF
POWER SAVE RF MODULATOR
] ] OFF ON
SELECT SET
: : OK
3 Press >/. to select the option you want to change:
1 Press OK after selecting TAPE OPTIONS or VIDEO OPTIONS.
VIDEO OPTIONS
AUTO TAPE SPEED TAPE SELECT [ ] 1 [ ] ON
SYSTEM [ AUTO ]
SELECT SET
: :
: :
2 Press >/. to select the option, then press ?// to change the setting.
Press ?// to change the setting. 4 Press OK to return to the original screen.
Menu choices Initial settings are indicated in bold print.
TAPE OPTIONS menu choices
Set this option to

VIDEO OPTIONS menu choices
Set this option to
Set this option to
Menu option · OPTIONS menu choices · Menu option

This VCR (Recorder) TV

continued

TV
… LINE-1 IN
VMC-2121 EURO-AV cable (not supplied)
: Signal flow
This VCR (Recorder) · Other VCR (Player) · EURO-AV (Scart)

1 Insert a source tape with its safety tab removed into the other (playback) VCR. Search for the point to start playback and set it to playback pause. 2 Insert a tape with its safety tab in place into this (recording) VCR. Search for the point to start recording and press P PAUSE. 3 Press r REC on this VCR to set it to recording pause. 4 To start editing, press the P PAUSE buttons on both VCRs at the same time.
To stop editing Press the p STOP buttons on both VCRs.
Note • If you start editing following the procedure above, the VCR won’t start recording with the OPC function. To record a tape with the OPC function, press r REC again during recording pause in step 3 so the VCR analyses the tape. Then, when you start editing in step 4, press P PAUSE after the OPC indicator stops flashing. If you press P PAUSE before the OPC indicator stops flashing, the OPC function is cancelled.
r REC

If you have any questions or problems not covered below, please consult your nearest Sony service facility.
The ON/STANDBY switch does not function.
The power is turned on but the VCR does not operate.
The clock has stopped and “–:– –” lights in the display window.
The playback picture does not appear on the TV screen.
The picture is not clear.
The picture rolls vertically during picture search.
The picture has no sound.
The sound is unstable or has an echo.


No TV programme appears on the TV screen.
TV reception is poor.
The tape starts playing as soon as it is inserted.
The tape is ejected when you press r REC.
Nothing happens when you press r REC.
The timer does not operate.

A tape cannot be inserted.
The remote commander does not function.
The tracking indicator does not appear on the screen.
The VCR needs to be cleaned.
Symptom · Remedy · Others

General
VHS E2-E12, R1-R12 UHF E21-E69, R21-R69 CATV S1-S41, S01-S05 RF output signal
23 W Operating temperature
UHF channels 21 to 69 Aerial out
5°C to 40°C Storage temperature
75-ohm asymmetrical aerial socket
–20°C to 60°C Dimensions
Approx. 430 × 100 × 314 mm (w/h/d) including projecting parts and controls Mass
21-pin Video input: pin 20 Audio input: pins 2 and 6 Video output: pin 19 Audio output: pins 1 and 3 LINE-2 IN
Approx. 4.6 kg
Remote commander (1) R6 (size AA) batteries (2) Aerial cable (1)
VIDEO IN, phono jack (1) Input signal: 1 Vp-p, 75 ohms, unbalanced, sync negative AUDIO IN, phone jack (2) Input level: 327 mVrms Input impedance: more than 47 kilohms LINE-2 OUT
Design and specifications are subject to change without notice.
AUDIO OUT, Phono jack (2) Rated output level: 327 mVrms Load impedance: 47 kilohms Output impedance: less than 10 kilohms VIDEO OUT, Phono jack (1) Rated output level: 327 mVrms Load impedance: 47 kilohms Output impedance: less than 10 kilohms
Channel coverage · Power requirements

Refer to the pages indicated in parentheses ( ) for details.
1 ON/STANDBY switch/indicator (10)
8 p STOP button (43)
9 P PAUSE button (43)
3 § EJECT button (21)
buttons (11, 32, 38)
4 03 REW (rewind) button (31)
RF (Radio Frequency) CHANNEL button (10, 12)
5 · PLAY button (31)
6 )# FF (fast-forward) button (31)
!™Remote sensor (5)
7 r REC (record) button (43)
48 Additional Information
2 Tape compartment · jacks (41)


1 Timer indicator (28)
6 Tracking indicator (37)
2 STEREO indicator (36)
7 Time counter/clock/line/ programme position indicator (22, 24, 43) 8 Remaining time indicator (25)
3 Tape speed indicators (24)
4 VIDEO indicator (9, 25)
5 OPC (Optimum Picture Control) indicator (37)
9 Tape/recording indicator (22, 24)
continued

Rear panel
1 Mains lead (8)
4 NTSC PB (playback) switch (21)
2 AERIAL IN ANTENNE ENTREE connector (8)
3 AERIAL OUT ANTENNE SORTIE connector (8)
6 LINE-2 OUT VIDEO/AUDIO L/R jacks (9)

1 TV / VIDEO remote control switch (5)

2 6␣EJECT button (21)
3 COUNTER RESET button (22)
4 DISPLAY button (25)
5 WIDE button (7)
6 TV/VIDEO button (9, 25)
7 ? (ten’s digit) button (26)
8 QUICK TIMER button (33)
9 r␣REC (record) button (24)
0 SP (Standard Play)/LP (Long Play) button (24)
!¡ INPUT SELECT button (24, 28)
!™&␣SLOW button (31)
!£ Tape/menu operation buttons (13,
21, 31, 34, 39)
MENU button P PAUSE/> button p STOP/. button 03 REW (rewind)/? button )# FF (fast-forward)// button · PLAY/OK button
!¢ ON/STANDBY switch (6, 28)
!∞COUNTER/REMAIN button (25)
!§ AUDIO MONITOR button (36)
!¶ CLEAR button (35)
!• Programme number buttons (6, 26)
!ª PROG (programme) +/– buttons (6,
@º VOL (volume) +/– buttons (for TV)
@¡ × 2 button (31)
@™REPLAY button (21)
17, 24) · (6)

L Language selecting 15 LP mode 24
S Safety tab 25 Searching at various speeds 31 SP mode 24
picture 19, 32, 37 tracking 32, 37 Aerial hookup 8 AFT (Auto Fine Tuning) 19 ATP (Auto Tuner Preset) 12 Audio track 36 Auto Set Up 12 Auto Tape Speed 39
T, U, V, W, X, Y, Z Timer recording 27 cancelling timer settings 34 changing timer settings 34 checking timer settings 34 daily/weekly recording 29 overlapping timer recordings 35 Tracking adjustment. See Adjusting
O OPC (Optimum Picture Control) 37
C Cleaning the video heads 44 Clock setting 13 Colour system
P Picture adjustment. See Adjusting Playback 20 at various speeds 31 frame-by-frame 31 slow motion 31 Power save 40 Presetting channels 12, 16
compatible colour systems 2 setting 21 Connecting
the VCR and your TV 8 to a TV with a EURO-AV connector 9 to a TV with LINE IN connector 9 Counter 22
D Disabling programme position 18 Dubbing. See Editing
R Recording 23 saving 25 while watching another programme 25 Remote commander 5 RF channel 10
H, I, J, K Hi-fi audio track 36
during playback 36 · Sony Corporation
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.