Instruction/ maintenance manual of the product PCS-1P Sony
Go to page of 78
COMMUNICATION SYSTEM PCS-1 PCS-1P SYSTEM INTEGRA TION MANUAL 1st Edition (V ersion 2.2 and later).
PCS-1/1P ! W ARNING This manual is intended for qualified service personnel only . T o reduce the risk of electric shock, fire or injury , do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
1 PCS-1/1P Table of Contents 1. Installation 1-1. Caution on Installation ................................................................................ 1-1 1-1-1. Lay Out the Videoconferencing Room ...................................... 1-1 1-1-2. Operating Environment .
2 PCS-1/1P 4. Technical Data 4-1. PCS-1/1P Port Number Used ...................................................................... 4-1 4-1-1. During P-P Connection (Default) ............................................... 4-1 4-1-2. P-P Connection (Custom: When TCP port number is set to 3000 and UDP port number is set to 3100) .
1-1 PCS-1/1P Section 1 Installation 1-1. Caution on Installation 1-1-1. Lay Out the Videoconferencing Room Arrange it in consideration of the space of a camera and microphone when laying out the videoconferencing room. Camera Range represents the shooting area of the camera when the zoom has been extended fully.
1-2 PCS-1/1P 90 d 2 m 1: For internal microphone 2: For extension microphone (PCS-A300) 120 d 0.5 to 1 m 3: For extension microphone (PCS-A1) 0.5 to 1.2 m Highly directional range of microphone The ideal directional range of a microphone is shown below.
1-3 PCS-1/1P The microphone built in the PCS-C1/C1P Camera Unit is assumed to be used to conduct a conference among about three participants. You can connect the optional PCS-A1 or PCS-A300 microphone to the System, allowing more persons to participate in the conference.
1-4 PCS-1/1P The blue line in the light emitter indicates the direction of infrared rays. Infrared light emitter : Adjustment in vertical direction : Adjustment in horizontal direction Document stand Infrared rays Infrared photosensor PCS-1/1P Installation of document stand a.
1-5 PCS-1/1P 45 d 30 d Infrared light emitter Infrared light emitter Infrared light emitter 5 m 15 d 3.5 m 2.5 m Infrared photosensor PCS-1/1P b. Installation range (Reference) If an image is disturbed in the range shown below, bring it near PCS-1/1P with the infrared light emitter of a documents stand turned toward PCS-1/1P.
1-6 PCS-1/1P 1-1-2. Operating Environment Layout Considerations . Avoid having large, moving objects, especially people, behind the participants, as the quality of the picture transmitted to the remote party will deteriorate. . Do not seat participants in front of a wall with fine stripe patterns.
1-7 PCS-1/1P Place used Unpacking Check of supplied accessories Power and cable connection, and preparation Start the power of the system and initialize. <Refer to “1-1. Caution on Installation” on page 1-1.> <Refer to “1-3. System Connections” on page 1-8.
1-8 PCS-1/1P 1-3. System Connections This section describes the typical system connections. m . Be sure to turn off all the equipment before making any connections. . Do not connect/disconnect the camera cable with the power on. Doing so may damage the Camera Unit or Communication Terminal.
1-9 PCS-1/1P 1-3-2. When Used in ISDN n Do not connect/disconnect the camera cable or the interface cable with the power on. Doing so may damage the Camera Unit, Communication Terminal or ISDN Unit.
1-10 PCS-1/1P 1-4. Initialization 1-4-1. Inserting Batteries into the Remote Commander Most of the operations with the Video Communication System can be controlled with the supplied Remote Commander. 1. Remove the battery compartment cover. 2. Insert two size AA (R6) batteries (supplied) with correct polarities into the battery compartment.
1-11 PCS-1/1P 1-4-2. Turning On/Off the TV Monitor Together With the Communication Terminal If you use a Sony TV, insert the IR repeater under the remote sensor of the TV. Once you set the IR repeater, the TV will turn on or go to standby together with the Communication Terminal when you press the I/O button on the supplied Remote Commander.
1-12 PCS-1/1P 1-4-3. Adjust the Volume of a Monitor Television Adjust the television side after the volume is adjusted on the PCS-1/1P side. 1. Press the volume/bright button of a remote controller and adjust so that the volume adjustment bar is in the center position 2.
1-13 PCS-1/1P 1-4-5. Turning On 1. Turn on the TV monitor. If the IR repeater is installed in the TV monitor, set the TV monitor to standby mode. The TV monitor will turn on simultaneously when the Communication Terminal is turned on. 2. Turn on the power of any other equipment to be used for the videoconference.
1-14 PCS-1/1P Language Setup Wizard Cancel Next English Language 1-4-6. When the power is first turned on after installation When the power is first turned on after installation, the wizard for initialization is displayed if self-diagnosis is completed.
1-15 PCS-1/1P Area Code Local Number Cancel Next Previous A2 A1 B1 B2 C1 C2 4. Press the ↑ , ↓ , ← , and → buttons of a remote controller and click the “ Next ” button. Press the Enter button. The ISDN setting wizard is displayed when ISDN unit PCS-B384 or PCS-B768 is connected.
1-16 PCS-1/1P LAN Setup Wizard Cancel Next Previous Auto DHCP Mode Host Name IP Address Network Mask Gateway Address DNS Address . . . . . . . . . . . . 11. Set the following items on LAN. DHCP mode: Sets DHCP (Dynamic Host Configuration Protocol). AUTO: Acquires an IP address, network mask, gateway address, and DNS address automatically.
1-17 PCS-1/1P Initial value LAN Auto 12B (768K) 1024Kbps None Auto All capabilities 15fps All capabilities On Off On Blank Auto Off Off Auto Answer 12B (768K) Auto 1024Kbps Off ALL 15fps ALL On Off On Line I/F Bonding Number of Lines LAN Bandwidth Prefix Restrict Video Mode Video Frame Audio Mode Far End Camera Control T.
1-18 PCS-1/1P Item General Setup Audio Setup Contents of setting Enter the terminal name to be notified to MCU. Set to “ On ” when using a dual monitor function with the two monitors connected. Select whether a signal should be output to the monitor connected to which output terminal.
1-19 PCS-1/1P DHCP Mode Host Name IP Address Network Mask Gateway Address DNS Address Gatekeeper Mode Gatekeeper Address User Alias User Number SNMP Mode Trap Destination Community Description Locatio.
1-20 PCS-1/1P Initial value Blank Blank Blank On On USA ★ 1 ★ National ISDN ★ Blank ★ Blank ★ Blank ★ Blank ★ Blank ★ Blank ★ Blank Blank Off Split 2B (128K) 1024Kbps Auto ALL ALL On On Off Contents of setting Set the password for an administrator.
1-21 PCS-1/1P Item Machine Information (Information) Status Encryption via LAN Page 1/1 Page 1/1 Initial value Off Blank Host Version ISDN UNIT Version DSB Version DSP Version Software Option Option I.
1-22 PCS-1/1P 1-6. Flowchart of Opening Test Opening test Communicate using ISDN? ISDN dialing ISDN answering LAN dialing LAN answering <Refer to “ 1-6-1. Dialing Procedure of ISDN ” on page 1-23.> <Refer to “ 1-6-2. Answering Procedure of ISDN ” on page 1-25.
1-23 PCS-1/1P 1-6-1. Dialing Procedure of ISDN n It is required that the line number used in the other end is entered in the area code and local number of the ISDN setup menu of the other end.
1-24 PCS-1/1P Item 6. 7. Operation The remote party makes a response. Disconnection Press the CONNECT/DISCONNECT ( / ) button of a remote controller. A confirmation message on whether to disconnect a line is then displayed.
1-25 PCS-1/1P 1-6-2. Answering Procedure of ISDN n It is required that the line number used in this unit is entered in the area code and local number of the ISDN setup menu before receiving a signal from the other end.
1-26 PCS-1/1P Item 1. 2. 3. 4. 5. Operation Select “ Dial ” from the launcher menu using ↑ , ↓ , ← , and → buttons of a remote controller and press the ENTER button, or press the CONNECT/DISCONNECT ( / ) button of a remote controller.
1-27 PCS-1/1P Item 6. 7. Operation The remote party makes a response. Disconnection Press the CONNECT/DISCONNECT ( / ) button of a remote controller. A confirmation message on whether to disconnect a line is then displayed.
1-28 PCS-1/1P Item 1. 2. 3. Operation Calling from the remote party <For Auto Answer> <For Manual Answer> Remote disconnection Screen Remarks (Confirmation item) A ringer tone occurs.
2-1 PCS-1/1P Section 2 Maintenance Connect Phone Book Dial Menu Show Help Angle Adj. More Options IP LAN Line I/F Dial A2 B1 B2 C1 C2 1024 Kbps LAN Bandwidth Dial Save 2-1. Confirmation Procedure of Local Terminal Operation Using Self-Loop A self-loop is the reflected loop in the codec of the main unit.
2-2 PCS-1/1P Connect Phone Book Dial Menu Show Help Angle Adj. More Options IP LAN Line I/F Dial A2 B1 B2 C1 C2 1024 Kbps LAN Bandwidth Dial Save 2-2. LAN Communication Test using Ping A LAN communication test can be performed using ping (ICMP). Operation procedure 1.
2-3 PCS-1/1P 2-3. Locating the Components Inspect the items below when this unit does not operate normally. 1. This unit does not start even if the power switch on the side panel is turned on. . Check that the power cable is connected properly. . Check that the POWER indicator (green) on the front panel of the main unit lights.
2-4 PCS-1/1P 6. A line is not connected. (LAN) . Check that the LAN cable is connected properly. . Check that the left indicator (green) of the main unit ’ s LAN connector blinks. . Check that the LAN indicator ( ) is highlighted in the system status display area (in the lower-right position of the screen) of the initial screen.
2-5 PCS-1/1P (RS-232C cross cable) PCS-1/1P Personal computer ON LINE POWER LAN ALERT 2-4. Operation Log PCS1/1P has a function that outputs the internal processing history, between the connection and.
2-6 PCS-1/1P (1) Click “ Start menu ” , “ Accessories ” , “ Communications ” , and then “ HyperTerminal ” . (2) Enter “ VT100 ” in “ Name ” , select any icon, and click the “ OK ” button.
2-7 PCS-1/1P (3) Select “ COM1 ” in “ Connect using ” and click the “ OK ” button. (4) Set the baud rate as described below and click the “ OK ” button.
2-8 PCS-1/1P (5) Click “ Capture Text ” from a “ Transfer ” menu. (6) Set the saving place and name of a log file and click “ Start ” ..
2-9 PCS-1/1P (7) After logging, click “ Stop ” from “ Capture Text ” in a “ Transfer ” menu. (8) Double-click the extracted log file to view a log.
2-10 PCS-1/1P Operation log using commercial PC (2) When PCS-1/1P is connected to LAN, a log can be extracted from PCS-1/1P using telnet with PC connected to LAN.
2-11 PCS-1/1P (2) Enter ping, and then enter the IP address of PCS-1/1P after spacing out. Press the [Enter] key and confirm that a reply is returned. After confirmation, close the command prompt. (3) Click “ Start menu ” , “ Accessories ” , “ Communications ” , and then “ HyperTerminal ” .
2-12 PCS-1/1P (4) Enter “ LAN ” in “ Name: ” , select any icon, and click the “ OK ” button. (5) Select “ TCP/IP (Winsock) ” in “ Connect using ” , enter the IP address of PCS-1/1P in “ Host address: ” , and click the “ OK ” button.
2-13 PCS-1/1P (6) Click “ Capture Text ” from a “ Transfer ” menu. (7) Set the saving place and name of a log file and click the “ Start ” button.
2-14 PCS-1/1P (8) The message below is displayed on the hyper terminal screen. PCS-1 Telnet Server login: Enter sonypcs and press the Enter key. Password: is then displayed. Press the Enter key again. A log begins to be extracted. (9) After log extraction is completed, click “ Stop ” from “ Capture Text ” in a “ Transfer ” menu.
2-15 PCS-1/1P Memory Stick slo t ON LINE ON LINE POWER POWER LAN LAN ALER ALER T POWER lamp (green) 2-5. Updating of Software The software of the main unit may be updated for improvement in a function. Two methods are available for updating. 2-5-1. Updating Using Memory Stick Turn off the power switch on the side panel of the main unit.
2-16 PCS-1/1P Dial Multipoint General ISDN Information Answer Audio Administrator LAN Status Setup Save Phone Book Load Phone Book Clear Phone Book Save Application Save Call Log Save System Log Save Setup Load Setup Clear Setup Load Application System Reset Service Command Save Cancel 2-6.
2-17 PCS-1/1P For loading of application 1. Display a service menu. 2. Insert the Memory Stick, in which the application software of the version to be loaded is recorded, into a Memory Stick slot. 3. Select “ Load application ” using ↑ , ↓ , ← , and → buttons of a remote controller and press the ENTER button.
2-18 PCS-1/1P 9) Load Setup The setup information (MSSONYPROTVCONFSETUPPCS_STUP.CSV) recorded in a Memory Stick is overwritten in the setup menu of the main unit. After execution, the screen disappears once, and a launcher menu is displayed in the same way as after the power is turned on.
3-1 PCS-1/1P Section 3 Compatibility in LAN Network LAN1 Teleconference terminal A 192.100.10.10 Teleconference terminal B 192.100.10.20 HUB LAN2 3-1. Connection via Hub Example of system When a call is initiated from teleconference terminal A to teleconference terminal B.
3-2 PCS-1/1P Fixed IP for PPPoE: OFF Fixed IP Address for PPPoE: Blank PPPoE DNS: Obtain automatically Primary DNS: Cannot be set. Secondary DNS: Cannot be set. 2. Confirm that the IP address displayed in the launcher menu of teleconference terminal B is 192.
3-3 PCS-1/1P 192.100.10.1 VPN 192.100.20.1 Teleconference terminal A 192.100.10.10 Teleconference terminal B 192.100.20.20 Router Router LAN1 LAN2 3-2. Connection via Router Example of system When a call is initiated from teleconference terminal A to teleconference terminal B.
3-4 PCS-1/1P PPPoE DNS: Obtain automatically Primary DNS: Cannot be set. Secondary DNS: Cannot be set. 2. Confirm that the IP address displayed in the launcher menu of teleconference terminal B is 192.100.20.20. 3. The LAN setup menu of teleconference terminal A is set as described below.
3-5 PCS-1/1P Teleconference terminal A Teleconference terminal B DHCP server A DHCP server B Router Router LAN1 LAN2 3-3. Connection via DHCP Example of system When a call is initiated from teleconference terminal A to teleconference terminal B. 1. The LAN setup menu of teleconference terminal B is set as described below.
3-6 PCS-1/1P PPPoE DNS: Obtain automatically Primary DNS: Cannot be set. Secondary DNS: Cannot be set. 2. Confirm that the IP address is displayed in the launcher menu of teleconference terminal B. (Example: IP:192.100.20.20) 3. The LAN setup menu of teleconference terminal A is set as described below.
3-7 PCS-1/1P 192.100.10.1 192.100.20.1 Teleconference terminal A 192.100.10.10 User name: PCS1A User number: 100 Teleconference terminal B 192.100.20.20 User name: PCS1B User number: 200 Gatekeeper 192.
3-8 PCS-1/1P 2. Confirm that the IP address displayed in the launcher menu of teleconference terminal B is 192.100.20.20. 3. Confirm that “ Registration Confirm ” is displayed at the bottom of page 2 in the LAN setup menu of teleconference terminal B.
3-9 PCS-1/1P Teleconference terminal A User name: PCS1A User number: 100 Teleconference terminal B User name: PCS1B User number: 200 DHCP server A DHCP server B Gatekeeper 192.
3-10 PCS-1/1P 2. Confirm that the IP address is displayed in the launcher menu of teleconference terminal B. (Example: IP:192.100.20.20) 3. Confirm that “ Registration Confirm ” is displayed at the bottom of page 2 in the LAN setup menu of teleconference terminal B.
3-11 PCS-1/1P 192.168.10.1 210.10.10.1 210.20.20.1 Teleconference terminal A 192.168.10.10 Teleconference terminal B 210.20.20.2 Router Internet Router 3-6. Connection beyond NAT Example of system A call is submitted from TV conference terminal A (NAT environment) to TV conference terminal B (global IP).
3-12 PCS-1/1P Fixed IP Address for PPPoE: Blank PPPoE DNS: Obtain automatically Primary DNS: Cannot be set. Secondary DNS: Cannot be set. 2. Confirm that the IP address displayed in the launcher menu of teleconference terminal B is 210.20.20.2. 3. The LAN setup menu of teleconference terminal A is set as described below.
3-13 PCS-1/1P Ethernet Ethernet ONU ONU FTTH FTTH Internet Regional IP network Teleconference terminal A 210.10.10.10 Teleconference terminal A 211.10.10.10 3-7. Connection using PPPoE Example of system When a call is initiated from teleconference terminal A to teleconference terminal B.
3-14 PCS-1/1P Primary DNS: Cannot be set. Secondary DNS: Cannot be set. 2. Confirm that the IP address displayed in the launcher menu of teleconference terminal B is 211.10.10.10. 3. The LAN setup menu of teleconference terminal A is set as described below.
4-1 PCS-1/1P Section 4 Technical Data 4-1. PCS-1/1P Port Number Used 4-1-1. During P-P Connection (Default) PCS-1/1P uses the port number below during P-P connection when the port number used in a LAN setup menu is set as “Default”.
4-2 PCS-1/1P 4-1-3. During Use of Internal MCU Function (Default) PCS-1/1P that operates as internal MCU uses the port number below when the port number used in a LAN setup menu is set as “ Default ” . The port number that a child-terminal uses is the same as during P-P connection.
4-3 PCS-1/1P 4-2. Setting of PCS-1/1P and HUB The initial setting of the PCS-1/1P is Auto. In the Auto setting of the PCS-1/1P, 10/100 can be selected automatically, however, Half/Full cannot be selected automatically. Therefore, if the HUB is set to Full mode, a connection failure or packet loss occurs.
4-4 PCS-1/1P 4-4. Audio Selection List of PCS-1/1P Audio setup menu Audio input Audio output CTE Input MIC Echo Selection Internal MIC mute AUDIO AUDIO OUT Receiving Remarks select select canceller in.
4-5 PCS-1/1P Audio input Audio output . Internal MIC: Microphone incorporated into the man unit . Remote: Remote audio . MIC: MIC input of main unit . MIC: MIC input of main unit . AUX: AUX input of main unit . AUX: AUX input of main unit . DSB MIC: MIC input of DSB .
4-6 PCS-1/1P 4-5. Remote Motion Picture Display during Multipoint Connection of PCS-1/1P 4-5-1. Remote Motion Picture Displayed at Each Point in Audio Detection Mode The whole screen at a speaking point is displayed in other terminals. The remote motion picture displayed at a speaking point remains before speaking.
4-7 PCS-1/1P 4-5-3. Remote Motion Picture at Each Point in Split Mode The images in all connected terminals are split and simultaneously displayed in all terminals. 1. The number of split images is 4 when sub-terminals are 1 to 3. The position of the images is fixed in the order of connection.
4-8 PCS-1/1P The transition examples of an image when the previous image displayed in the lower-right position is one in a main terminal and when sub-terminal B speaks are given below.
4-9 PCS-1/1P 4-6. Display Transition List of PCS-1/1P General setup Dual monitor: Off Monitor output: VIDEO OUT In this case, connect a video monitor to the VIDEO OUT MAIN terminal of the main unit.
4-10 PCS-1/1P General setup Dual monitor: On Monitor output: RGB OUT In this case, connect a video monitor to the VIDEO OUT MAIN terminal of the main unit and connect an RGB monitor to the RGB terminal of the main unit. The display transition is as shown below.
4-11 PCS-1/1P 4-7. Priority Level List of Video and Audio Codec High-speed bit rate of H.323 (512 K or higher) 1234567 Sound quality V H264/30 fps MPEG4/30 fps SIF/60 fps G263/30 fps H261/30 fps __ priority A MPEG4 AAC G722 G722.1 G711 G728 G729 G723.
4-12 PCS-1/1P Middle-speed bit rate of H.320 (256 K to 511 K) 1234567 Sound quality V H264/15 fps H263/15 fps H261/15 fps ____ priority A G722 G711 G728 ____ Picture quality V H264/15 fps H263/15 fps .
.
Sony Corporation 2004. 7 22 PSNC BCC B2B Solutions Div . ©2003 PCS-1 (UC) PCS-1P (CE) E.
An important point after buying a device Sony PCS-1P (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sony PCS-1P yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sony PCS-1P - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sony PCS-1P you will learn all the available features of the product, as well as information on its operation. The information that you get Sony PCS-1P will certainly help you make a decision on the purchase.
If you already are a holder of Sony PCS-1P, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sony PCS-1P.
However, one of the most important roles played by the user manual is to help in solving problems with Sony PCS-1P. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sony PCS-1P along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
