Instruction/ maintenance manual of the product TPC-1261H B&B Electronics
Go to page of 106
TPC-1261H GX3 LX800 T ouch Panel Computer with 12.1" SVGA TFT LCD User Manual.
TPC-1261H User Manual ii Copyright The documentation and th e software included with this product are copy- righted 2004 by Advantech Co., Lt d. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time wi thout notice.
iii Product W arranty (1 year ) Advantech warrants to you, the original purchaser , that each of its prod- ucts will be free from defects in ma terials and workman ship for one year from the date of purchase.
TPC-1261H User Manual iv CE This product has passed the CE test for environmental specificati ons when shielded cables are used for external wiring. W e recommend the use of shielded cables. This kind of cable is available from Advantech. Please contact your local supplier for ordering inform ation.
v Packing List Before setting up the system, check that the items listed below are included and in g ood condition. If any item d oes not accord w ith the table, please contact y our dealer immediately .
TPC-1261H User Manual vi 13. Never open the equi pment. For safety reasons, the equipment should be opened only by qualifi ed service personnel. 14. If one of the following si tuations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged.
vii Table of Contents Contents Chapter 1 General Information ....................................... 2 1.1 Introduction ............ ............................ ............ ........... ........ 2 1.2 Specifications ............ .....................
TPC-1261H User Manual viii Figure 4.14:Update Dri ver - 1 ... ............. ........... ........... 25 Figure 4.15:Update Dri ver - 2 ... ............. ........... ........... 25 Figure 4.16:Update Dri ver - 3 ... ............. ........... ...........
ix Table of Contents C.2.2 IOCTL _WDT_DISABLE: ....... ........... ........... ......... .... 60 C.2.3 IOCTL_WDT_STROBE: ........... ......... ........... ......... .... 60 C.2.4 IOCTL_WDT_GETTIMEOUT : ........ ........... ........... .... 61 C.2.5 IOCTL_WDT_SETTIMEOU T: .
TPC-1261H User Manual x Figure F.2:Ins tall Wizard - 1 ...... ........... ........... ......... .. 84 Figure F.3:Ins tall Wizard - 2 ....... ........... ........... ......... .. 85 Figure F.4:Ins tall Wizard - 3 ....... ........... ........... .......
2 CHAPTER 1 General Information This chapter gives b ackground infor- mation on TPC-1261H.. Sections include: • Introduction • Specifications • I/O Ports Arrangement • Panel Mounting • Explo.
TPC-1261H User Manual 2 Chapter 1 General Information 1.1 Introduction The TPC-1261H touch panel computer is a state-o f-the-art HMI (Human Machine Interface).
3 Chapter 1 1.2 Specifications 1.2.1 System Kernel • CPU: GeodeLink Cont rol Processor LX800 500MHz • BIOS: A ward 512KB flash memory • South Bridge: GeodeLink Control Processor CS5535 • VGA: GeodeLink C ontrol Processor LX800 50 0MHz • Ethernet: Realtek R TL8100BL; IEEE 802.
TPC-1261H User Manual 4 Environment • Operating T emperature: 0 ~ 50° C (32 ~ 122° F) • S torage T emperature: -20 ~ 60° C (-4 ~ 140° F) • Humidity: 40° C @ 10~95% relative humidity (non-cond ensing) • V ibration: 1 grms (5~5 00Hz) 1.3 LCD Specifications • Display T ype: TFT color LCD • Size (diagonal): 12.
5 Chapter 1 1.5 Power • Input V oltage: 18 - 32V DC (th e fuse will become an open circuit if the input level exceeds 33 V DC ) • Ty p i c a l : 24V DC @2.5Amp 1.6 I/O Port s Arrangement The arrangement of the I/O ports is shown in Figure 1.1. Figure 1.
TPC-1261H User Manual 6 Figure 1.2: Panel Mounting 1.8 Dimensions and Cutout • W eight: 4.1 kg (without HDD) • Dimensions: 31 1 x 237 x 58 mm (W x H x D) • Cutout: 302 x 228 mm (suggest ed).
7 Chapter 1 Figure 1.3: Dimensions.
TPC-1261H User Manual 8.
2 CHAPTER 2 System Setup This chapter provides a brief explana- tion for operating TPC-1261H..
TPC-1261H User Manual 10 Chapter 2 System Setup Y ou can easily get TPC-1261 H started by following the b elow steps. • Step 1: Unpack the TPC-1261H p ackage. Check the packing list at the beginning of th is manual to make sure all items have been included.
11 Chapter 2 • Step 2: Install a CompactFlash card containi ng W indows CE, embed- ded W indow s XP or another operating system . Figure 2.2: Install CompactFlash Memory Card • Step 3: Connect the po wer connector to the 24 V DC power lines. The power lines can either be of some power adapter or in-house power source.
TPC-1261H User Manual 12 • Step 4: Plug th e power lines into the system power receptor . • Step 5: Push the power button to power on the system (figure 2.4). • Step 6: Calibrate the touchscreen (click "PM" i n the bottom corner). Figure 2.
2 CHAPTER 3 System Engine.
TPC-1261H User Manual 14 Chapter 3 System Engine T able 3.1: Mainboard Connectors & Jumper Settings Label Funct ion Description CN2 LCD POWER LCD INVERTER Connector CN3 CF Compa ctFlash socket CN4.
15 Chapter 3 Figure 3.1: Main Board Connect ors - 1 Figure 3.2: Main Board Connect ors - 2.
TPC-1261H User Manual 16.
2 CHAPTER 4 Sof tware Configuration Sections include: • VGA Driv er Installat ion • Advantech COM Installation • Entertainment Encryp tion/ Decryption Driver Installation.
TPC-1261H User Manual 18 Chapter 4 Sof tware Configuration A support CD-ROM for TPC-1261H is available an d along with the product. There are related utilities and drivers of TPC-1261H for W indows XP .
19 Chapter 4 Figure 4.2: Update D river Step 3: Then follow the update wizard processures. Figure 4.3: Update Wizard-1.
TPC-1261H User Manual 20 Figure 4.4: Update W izard-2 Figure 4.5: Update Wizard-3.
21 Chapter 4 Figure 4.6: Update W izard-4 Figure 4.7: Update Wizard-5.
TPC-1261H User Manual 22 Figure 4.8: Update W izard-6 Step 4: After you successfully upda te the driver , you can see the VGA successfully installed from the device mana ger .
23 Chapter 4 4.2 Advantech CO M Driver Inst all T wo com ports named COM3 and COM4 on TPC-1261H are Advantech Special com port. Please follow the steps below to install the d river . Step 1: Insert the CD-ROM into your CD-ROM drive. Go to the direc- tory: …TPC-1261HDriv erCom Port Driver and then excute PCI_ICOM.
TPC-1261H User Manual 24 Figure 4.12: PCI ICOM Installation - 2 Step 3: Then, go to “Device Manager” to update the driver . Click “?PCI Serial Port” and then select “Driver” T ab to update driver as shown in Figure 4.
25 Chapter 4 Figure 4.14: Update Driver - 1 Step 4: Follow the hardw are upd ate wizard as the figures below . Figure 4.15: Update Driver - 2.
TPC-1261H User Manual 26 Figure 4.16: Update Driver - 3 Step 5: Complete the PCI-1602 Se ries Slave Bridge installation. Figure 4.17: Slave Bridge Installation Complete.
27 Chapter 4 Step 6: Then, go to “Device Manager”. Y ou can find “Advantech PCI- 1602 Series Slave Br idge” is on the list. Figure 4.18: PCI-1602 Device Manager Step 7: And then c l ick “? PCI Seri al Port” to update the driver .
TPC-1261H User Manual 28 Figure 4.19: PCI Serial port Device Manager Figure 4.20: Update Driver - 1.
29 Chapter 4 Step 8: Follow the hardw are upd ate wizard as the figures below . Figure 4.21: Update Driver - 2 Figure 4.22: Update Driver - 3.
TPC-1261H User Manual 30 Step 9: Complete the Advantech PCI-1602 Series Master Bridge installa- tion. Figure 4.23: PCI-1602 Master Installation Step 10: Then, follow the wizard the install the software for Advantech PCI serial ports as the below . Figure 4.
31 Chapter 4 Figure 4.25: PCI Serial Port Installation - 2 Figure 4.26: PCI Serial Port Installation - 3.
TPC-1261H User Manual 32 Figure 4.27: PCI Serial Port Installation - 4 Figure 4.28: PCI Serial Port Installation - 5.
33 Chapter 4 Figure 4.29: PCI Serial Port Installation - 6 Figure 4.30: PCI Serial Port Installation - 7.
TPC-1261H User Manual 34 Step 1 1: After the steps are done, the software for the com3 and com4 is successfully installed. Go to “D evice Manager” and find the list as below . Figure 4.31: Installation Complete 4.3 Entert ainment Encryption/Decryption Driver Step 1: Insert the CD-ROM and go to “Device Manager”.
35 Chapter 4 Step 2: Following t he install shie ld wizard to finish the setup. Figure 4.33: Inst all W izard - 1 Figure 4.34: Install W izard - 2.
TPC-1261H User Manual 36 Figure 4.35: Install W izard - 3 Step 4: The driver is successfully installed. Y ou can check via “Device Manager” as the below .
2 CHAPTER 5 F e a t u r e s i n Windows XP Embedded Sections include: • EWF • HORM • Advantech U tilities.
TPC-1261H User Manual 38 Chapter 5 Features in Windows XP Embedded TPC-1261H supports the embedd ed W in dows platform. This section out- lines the importan t featur es (EWF and HORM), that are provided in W in- dows XP embedded. 5.1 EWF EWF stands for Enhanced W rite Filter .
39 Chapter 5 5.2 HORM HORM stands for Hibernate Once R esume Many . In HORM environ- ment, a single hi bernation file is used to boot th e system repeatedly . T o set a HORM environment, pleas e follow the steps below . Please make sure EWF is disabled.
TPC-1261H User Manual 40 5.3.1 V ersion Informati on Start menu-> All Programs -> Advantech This states the current XPE runtime information in cluding hardware plat- form, version, bui ld number , release date, XPE QFEs installed in compo- nent database and XP Pro Patches you in stalled manually .
41 Chapter 5.
TPC-1261H User Manual 42.
2 APPENDIX A Serial Port Settings.
TPC-1261H User Manual 44 Appendix A Serial Port Settings A.1 COM1/ COM2/ COM3 Connector Definition Pin Signal 1N D C D 2N R X 3N T X 4N D T R 5G N D 6N D S R 7N R T S 8N C T S 9N R I Note: COM1 and COM2 only suppor t half-duplex (Maximum baud rate: 1 15.
45 Appendix A A.2 COM4 Setting The serial port COM4 on the TPC-1570H is adjustable. It can be set to RS-232, RS- 422 or RS -485. This po rt is designe d with auto data flow control capability. In other word , the TPC-1570H can automatically detect the data flow direction at this port when the two wired RS-485 communication is activated.
TPC-1261H User Manual 46 PIN RS-232 RS-422 RS-485 1 NDCD TX- D- 2N R X T X + D + 3N T X R X + 4 NDTR RX- 5 GND GND GND 6 NDSR 7N R T S 8N C T S 9N R I.
2 APPENDIX B W atchdog T imer Programming.
TPC-1261H User Manual 48 Appendix B W atchdog T imer Programming B.1 Overview The TPC-1261H watchdog tim er can be used to monitor system software operation and take correc tive action if the software fails to functio n after the programmed period. This section descri bes the operation of the watchdog timer, and how to program it.
49 Chapter B B.2 W atchdog Timer Programming The I/O port address of the watchdog timer is 2E(hex) and 2F(hex), 2E (hex) is the address port. 2F(hex) is the data port. Y ou must fi rst assign the address of register by writing addr ess value into address port 2E(hex), then write/read data to/from the assigned reg ister through data port 2F (hex).
TPC-1261H User Manual 50 T able B.1: W atchdog Timer Registers Address of register (2E) Attribute Description Read/Write V alue (2F) and description 87 (hex) ----- Write this address to I/O address port 2E (hex) twice to unlock the W83627HF 07 (hex) write Write 08 (hex) to select register of watchdog timer .
51 Chapter B B.3 Example Programs 1. Enable watchdog timer and set 10 sec. as timeout interval ;-------- --------- -------- --------- ---------- --------- ------ Mov dx,2eh ; Unlock W83627HF Mov al,87.
TPC-1261H User Manual 52 Out dx,al Inc dx Mov al,10 Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; lock W8 3627HF Mov al,0aah Out dx,al 2.
53 Chapter B Out dx,al Inc dx In al,dx Or al,08h Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; Set timeout interval as 5 minutes and start co unting Mov al,0f6h.
TPC-1261H User Manual 54 Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; Enable watchdog timer to be reset by mouse Mov al,.
55 Chapter B Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; Enable watchdog.
TPC-1261H User Manual 56 ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;-------- --.
2 APPENDIX C W atchdog T imer Programming on WinCE.
TPC-1261H User Manual 58 Appendix C W atchdog T imer Program- ming on WinCE There is a built-in watchdog timer in Windows CE 4.2 for TPC-1261H. Y ou can access it through the WIN32 API. TPC-1261H provides a WDT driver to allow users to enable/disable the watc hdog timer .
59 Appendix C C.1.1 Parameters • hDevice [in] Handle to the device that is to perform the operation. Call the Cre- ateFile function to obt ain a device handle.
TPC-1261H User Manual 60 C.2 How to Use the Control Code There are 6 control codes for the op eration codes in the WDT driver . C.2.1 IOCTL _WDT_ENABLE: Enables the watchdog timer of your appl ication.
61 Appendix C C.2.4 IOCTL_WDT_GETTIMEOUT : Gets the W atchdo g time setting. lpInBuffer: unused. nInBufferSize: unused. lpOutBuffer: The DWORD po ints to your wa tchdog time setting .
TPC-1261H User Manual 62 C.3 Examples #define WDT_CODE(ID) CTL_CODE(FILE_DEVICE_UNKNOWN,ID , METHOD_BUFFERED, FILE_ANY_ACCESS) #define IOCTL_WDT_ENABLE WDT_CODE (0x900) #define IOCTL_WDT_DI SABLE WDT_.
63 Appendix C // Set the W atchdog T i mer as 10 seconds. Num ber 2 means 10 seconds. DeviceIoControl(m_hWDT , IOCTL_WDT_SET_TIMEOUT , &nIndex, sizeof(nIndex), NULL, 0, &dwT emp, NULL); // Enable the W atch dog timer DeviceIoControl(m_hWDT , IOCTL_WDT_ENABLE, NULL, 0, NULL, 0, &dwT emp, NULL); While (1) { // do your job here.
TPC-1261H User Manual 64.
2 APPENDIX D Accessory Kit Assembly Procedure This appendix shows how to connect to a CD-ROM via the CompactFlash slot.:.
TPC-1261H User Manual 66 Appendix D Accessory Kit Assembly Procedure D.1 Comp actFlash to IDE T ransfer Kit Please follow this assembly procedur e to us e the CompactFlash slot to connect with a CD-ROM drive. 1. Connect the IDE cable to the adapter board.
67 Appendix D 2. Insert the adapter board into the Co mpactFlash slot. Figure D.3: CompactFlash Slot Figure D.4: Insert the Adapter Board into the CF slot Figure D.
TPC-1261H User Manual 68 Connect the CD-ROM to the adapter board via the IDE cable and then connect the exte rnal power line to the CD-ROM. Figure D.6: Connect the CD-ROM via the IDE Cable Figure D.
2 APPENDIX E HDD Kit Assembly.
TPC-1261H User Manual 70 Appendix E HDD Kit Assembly TPC-1261H provides two way to assem ble the HDD into the system. The ruggized HDD kit is to resist against the high vib ration. E.1 Ruggedized HDD Kit Please follow the assembly procedure to install the HDD into the system.
71 Appendix E Figure E.2: Required Parts.
TPC-1261H User Manual 72 2. Place the base bracket on the r ear case and carefully pull out the FPC cable through the hole of the b racket . Figure E.3: Opening the T op 3.
73 Appendix E 4. Carefully connect the FPC cable to the HDD and then put the HDD insultor on the HDD. Figure E.5: Connectting the FPC with the HDD Figure E.
TPC-1261H User Manual 74 5. Fasten the HDD holder with the HDD and HDD insulator . Please turn over the HDD holder and fasten them with 4 screws. Figure E.
75 Appendix E 6. Mount the H DD cushions with the HDD holder . Figure E.9: Mounting the cushions - 1 Figure E.10: Mounting the cushions - 2.
TPC-1261H User Manual 76 7. Place the HDD holder on the rear cover of the system and then fas- ten the holder with the system by four screws. Then, the assembl y of high vibration resistance HDD module is done. Figure E.1 1: Placing the HDD holder - 1 Figure E.
77 Appendix E Figure E.13: Fasten ing the HDD holder E.2 Internal HDD Kit Assembly Please follow the steps to assemble the internal HDD kit. 1. Remove the default HDD cover from the system.
TPC-1261H User Manual 78 2. There are four rubber screw casings, and four screws . Places the screws into their casings Figure E.15: Placing a sc rew into its rubber casing 3.
79 Appendix E 4. Connect the FPC cable to the HDD Figure E.17: Connecting the FPC cable 5. Put the HDD into the hole of the rear case. Figure E.18: Inserting the H DD.
TPC-1261H User Manual 80 6. Lay the HDD i nsulator in right directio n. Figure E.19: Laying in the HDD insulator 7. Place the default HDD cover on the system.
81 Appendix E 8. Fasten the default HDD cover with the system. Figure E.21: Re-fastening the cover - 1 Figure E.22: Re-fastening the cover - 2.
TPC-1261H User Manual 82 9. Place the bracket of PCI/104 on the slot and fasten it into place. Figure E.23: Fastening the PCI/104 bracket - 1 Figure E.
2 APPENDIX F T ouchscreen Inst allation & Configuration This appendix demo nstrates how to install the PenMount touchscreen and set the configuration on TPC-1261H.
TPC-1261H User Manual 84 Appendix F T ouchscreen Inst allation & Configuration F .1 Driver Inst allation Please insert the x86 TPC series suppor t CD and go to the driver folder: (TPC-1261HDriverUSB touch screen). Click setup.exe Figure F .1: Se tup.
85 Appendix F Figure F .3: Install Wizard - 2 Figure F .4: Install Wizard - 3.
TPC-1261H User Manual 86 F .2 Uninst all the Driver Please go to Settings and then select Control Panel. Please click Add/ Remove Progr ams. Figure F .5: Uninstall -1 Select PenMount USB. Click Remo ve button. Then, select “Y es” to remove the PenMountUSB driver and reboot the system .
87 Appendix F F .3 T ouchscreen Calibration The “PM”, the i con of the PenMount Control Panel, is in the menu b ar after the touchscreen installation. Pl ease click the icon “PM” to call Pen- Mount Control Panel. It contains six fun ctions: Calibrate, Draw , Option, and About.
TPC-1261H User Manual 88 Figure F .8: S tandard Calibration -2 Figure F .9: S tandard Calibration -3.
89 Appendix F Advanced Calibration is for the aged tou chscreens by using 4, 9, 16 or 25 points to calibrate touch panel. Figure F .10: Advanced C alibration -1 Note T ouch the red sq uares in sequence. The cali- bration is completed af ter the fift h touch red point is calibrated.
TPC-1261H User Manual 90 Figure F .1 1: Advanced Calibration -2 Figure F .12: Plot Calib ration Data.
91 Appendix F Draw This is to test the touchscreen operation. Its display show s touch loca- tion. Figure F .13: Draw Click “menu” and then click “clear screen” to clear the drawing.
TPC-1261H User Manual 92 Figure F .14: Clear Screen Option This option is t o set the operatio n mode and b eep sounds if t he beep sound is enabled. The operation mode, stream mode and point mode, is to enable/ disable the mouse’ s ability to drag on-screen icons.
93 Appendix F Figure F .15: Option.
TPC-1261H User Manual 94.
2 APPENDIX G Fuse S p ecifications.
TPC-1261H User Manual 96 Appendix G Fuse S p ecifications G .1 Fuse Specifications Rating : 250 V AC, 5 A Size: 5 x 20 mm G .2 Fuse Replacement Step 1: Remove the fuse cover Step 2: Replace the damaged fuse with a new one Step 3: Place the fuse co ver back into position.
An important point after buying a device B&B Electronics TPC-1261H (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought B&B Electronics TPC-1261H yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data B&B Electronics TPC-1261H - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, B&B Electronics TPC-1261H you will learn all the available features of the product, as well as information on its operation. The information that you get B&B Electronics TPC-1261H will certainly help you make a decision on the purchase.
If you already are a holder of B&B Electronics TPC-1261H, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime B&B Electronics TPC-1261H.
However, one of the most important roles played by the user manual is to help in solving problems with B&B Electronics TPC-1261H. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device B&B Electronics TPC-1261H along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
