Instruction/ maintenance manual of the product CDX-1000RF Sony
Go to page of 38
1 Model Name Using Similar Mechanism CDX-2500R CD Drive Mechanism T ype MG-363X-121 Optical Pick-up Name KSS-521A SERVICE MANUAL US Model CDX-1000RF COMP ACT DISC PLA YER A UDIO PO WER SPECIFICA TIONS.
2 T ABLE OF CONTENTS 1. GENERAL Location of controls ................................................................. 3 Getting Started ......................................................................... 3 Operation ............................
3 SECTION 1 GENERAL This section is extracted from instruction manual..
4.
5 3 claw 1 claws 4 CNP801 5 panel assy, front 2 claws 7 PTT 2.6x6 3 PTT 2.6x6 6 PTT 2.6x 6 2 PTT 2.6x6 4 CNP701 8 bracket (M/D) 5 CD mechanism block 1 PTT 2.6x6 SECTION 2 DISASSEMBL Y Note : Follow the disassembly procedure in the numerical order given.
6 2 PTT 2.6x6 4 chassis (rear) 1 PTT 2.6x6 3 PTT 2.6x 6 4 ground point screws (PTT 2.6x6) 5 ground point screw (PTT 2.6x6) 1 PTT 2.6x6 6 MAIN board 3 PTT 2.
7 4 claws 2 DISC IN SW board 7 lever (L) assy 3 tension spring (LR) 6 lever (R) assy 5 guide (disc) 1 PS 2x4 5 chassis (T) sub assy 3 P 2x3 4 P 2x3 1 Unsolder the lead wires.
8 Fig. 1 4 PS 2x3 5 LOAD SW board 1 tension spring (RA) 2 arm (roller) 3 roller assy washer arm arm ring (roller), retaining spacer, insulating 7 PS 2x4 1 CN3 3 Removal the solders. 4 Removal the solders. 5 P 2x3 6 loading motor assy 9 SERVO board 2 CN2 8 PS 2x4 2-7.
9 1 tension spring (KF1) 8 compression spring (FL) 7 chassis (OP) (O/S) assy 9 compression spring (FL) 2 tension spring (KR1) 5 Fit lever (D) in the direction of the arrow. 3 damper (T) 4 damper (T) 6 Turn loading ring in the direction of the arrow. 1 P 2x3 2 sled motor assy 3 optical pick-up block 2-9.
10 IC3 CN1 IC1 CN2 FOCUS GAIN ADJ RV4 TP (RF. GND) IC2 TP (RF) CN3 RV1 FOCUS BIAS ADJ RF signal waveform VOLT/DIV: 200 mV TIME/DIV: 500 nS level: 1.0 – 1.5 Vp-p SERVO board TP (RF) TP (RF. GND) oscilloscope + – CD SECTION Note: 1. CD Block basically constructed to operate without adjustment.
11 11 4-1. IC PIN DESCRIPTION • IC801 µ PD17705GC-547-3B9 (SYSTEM CONTR OL) Pin No. Pin Name I/O Pin Description 1 NC — Not used. (Connect to ground in this set.
12 12 35 31 36 39 38 PD1 RF CLKO XLTO DATO SEIN FOK CNIN RF 0 21 PCMD 22 BCK 20 LRCK 34 XTAI 19 CLK 20 XLT 21 DATA 24 SENS 25 FOK 23 14 DIN 59 57 56 54 1 55 C.
13 13 CD L-CH CD SECTION (1/2) A 2 1 PJ401 AUDIO OUT L/R VOLUME CONTROL Q30 L/R LEVEL CONTROL Q29 MUTE Q401 18 1 17 13 15 6 8 VOLUME CONTROL Q22 LEVEL CONTROL Q23 MUTE CONTROL Q403,404 47 44 43 76 77 PMUTE Q45 BUFFER Q1 RF AMP Q2,3 BUFFER AMP Q81,82 35 31 RELAY SWITCH Q15 RELAY CONTROL Q16 8 TRANSMITTER L/R BALANCE RV1 X801 4.
14 14 80 66 RESET LCD_DAT 65 LCD_CLK 24 54 ADKI1 LCD_CE DATA CLK CE ILLON 78 BU_IN SYSTEM CONTROL IC801 (3/3) LCD DRIVER IC851 BACK-UP CHECK Q908,911,912 ACC CHECK Q909 LCD DRIVER POWER CONTROL Q913,9.
15 15 DISC IN SW board DISPLAY board LOAD SW board SERVO board MAIN board LIMIT SW board SUB board 4-5. CIRCUIT BO ARDS LOCA TION • W avef orms (MODE:PLA Y) 1 2 3 4 5 6 7 Approx. 620mVp-p IC2 1 (FEO) 0V IC2 ea (RFO) 1.2Vp-p Approx. 200mVp-p IC2 rs (TEO) 0V IC1 3 (MDP) 2.
16 16 CDX-1000RF 4-6. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 15 for Circuit Boards Location. (Page 18) Ref. No. Location IC1 D-2 IC2 E-5 IC3 B-2 Q1 F-5 Q2 F-6 • Semicon.
17 17 CDX-1000RF 4-7. SCHEMA TIC DIA GRAM — CD MECHANISM SECTION — • Refer to page 15 for Wa veforms. • Refer to page 23 for IC Block Diagrams.
18 18 (Page 22) (Page 16) CDX-1000RF 4-8. PRINTED WIRING BOARD — MAIN SECTION — • Refer to page 15 for Circuit Boards Location. D1 F-13 D2 F-11 D401 A-7 D402 A-8 D901 F-1 D902 D-1 D903 H-1 D904 .
19 19 8 9 10 11 12 CDX-1000RF Note: • V oltage is dc with respect to ground under no-signal condition. no mark : CD PLA Y (Page 21) (Page 20) (Page 17) 4-9. SCHEMA TIC DIA GRAM — MAIN SECTION (1/2) — • Refer to pa g e 21 for Wa veforms. • Refer to page 25 f or IC Block Diagrams.
20 20 13 CDX-1000RF Note: • V oltage is dc with respect to g round under no-signal condition. no mark : CD PLA Y (Page 19) 4-10. SCHEMA TIC DIA GRAM — MAIN SECTION (2/2) — • Refer to page 21 for Wa veforms. • Refer to page 25 f or IC Block Diagrams.
21 21 4-11. SCHEMA TIC DIA GRAM — DISPLA Y SECTION — Note: • V oltage is dc with respect to ground under no-signal condition. no mark : CD PLA Y (Page 19) CDX-1000RF • W avef orms (MODE:PLA Y) 8 9 q; qa qs qd IC701 4 (LRCIN) IC701 6 (BCKIN) 5.
22 22 CDX-1000RF 4-12. PRINTED WIRING BOARD — DISPLA Y SECTION — • Ref er to page 15 for Circuit Boar ds Location. (Page 18) D851 C-5 D861 A-1 D862 B-1 D863 C-1 D864 B-3 D865 B-11 D866 B-12 D867 B-13 D868 C-3 IC851 C-7 • Semiconductor Location Ref.
23 IC1 CXD2507A Q (SER V O Board) IC3 BA6796FP-T1 • IC Block Diagrams XLON SPOD SPOC SPOB SPOA CLKO VDD CNIN SEIN CLOK XLAT XLTO DATO 52 53 54 55 56 57 58 59 60 61 62 63 64 51 SERVO AUTO SEQUENCER 3.
24 IC2 CXA1782BQ PHD 2 PHD 1 PHD LD RF O RF I CP CB CC1 CC2 FOK SENS C.OUT XRST DATA XLT CLK VCC ISET SL O SL M SL P TA O TA M FSET TG2 TGU SRCH FE O FLB FGD FDFCT FE M FEI FEO FE BIAS F E EI VEE TED .
25 IC1 BA1405F-E2 (MAIN Board) IC701 PCM1717E-S 18 17 16 15 14 13 12 11 10 1 2 3 4 5 6 7 8 9 L AMP R AMP MPX BUFFER BUFFER 1/2 OSC 38kHz L IN BALANCE BALANCE NC VCC MPX OUT NC PILOT OUT NC R IN AMP BI.
26 1 2 3 4 5 6 7 7 8 9 10 #1 #1 #1 #1 #1 #1 #1 #1 F901 F902 #1 #1 #1 #1 MG-363X-121 CN601 SECTION 5 EXPLODED VIEWS NO TE: • The mechanical parts with no reference number in the exploded vie ws are not supplied. • Items marked “ * ” are not stocked since they are seldom required for routine service.
27 5-2. FRONT P ANEL SECTION Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 51 52 53 54 55 56 57 58 #2 LCD851 51 3-043-188-01 BUTTON (PLA Y) 52 X-3378-481-1 P ANEL ASSY , FR.
28 102 104 111 112 103 109 101 107 111 112 105 106 108 114 115 110 113 116 #4 #4 #3 #3 #3 #4 #5 M903 C C #4 5-3. CD MECHANISM SECTION (1) (MG-363X-121) Ref.
29 155 154 151 156 157 158 160 162 161 164 159 152 152 152 153 163 157 #5 D D 165 166 166 5-4. CD MECHANISM SECTION (2) (MG-363X-121) Ref. No. Part No.
30 #6 M902 #5 #4 #4 #7 M901 212 211 209 210 213 208 205 206 204 203 202 207 201 5-5. CD MECHANISM SECTION (3) (MG-363X-121) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark The components identified by mark 0 or dotted line with mark 0 are critical for safety .
31 SECTION 6 ELECTRICAL P ARTS LIST NOTE: • Due to standardization, replacements in the parts list may be dif ferent fr om the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may hav e some difference from the original one.
32 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark MAIN LOAD SW * 1-659-835-12 LIMIT SW BOARD *************** < SWITCH > SW3 1-572-688-11 SWITCH, PUSH (1 KEY) (LIMIT) *.
33 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark MAIN < JACK > CNJ600 1-793-598-11 JACK (ANTENNA IN) < DIODE > D1 8-719-058-78 DIODE HVU202A3TRF D2 8-719-991-33 DIODE 1SS133T -77 D401 8-719-991-33 DIODE 1SS133T -77 D402 8-719-109-71 DIODE MTZJ-T -77-3.
34 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark MAIN R5 1-216-063-11 RES-CHIP 3.9K 5% 1/10W R6 1-216-073-00 MET AL CHIP 10K 5% 1/10W R7 1-216-073-00 MET AL CHIP 10K 5% 1/1.
35 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark S E RVO < V ARIABLE RESISTOR > RV10 1-241-761-11 RES, ADJ, CARBON 1K RV11 1-238-019-11 RES, ADJ, CARBON 47K < RELA.
36 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark SUB JR35 1-216-296-00 SHORT 0 JR36 1-216-296-00 SHORT 0 JR37 1-216-296-00 SHORT 0 JR38 1-216-296-00 SHORT 0 JR39 1-216-296-.
37 Ref. No. Part No. Description Remark ************** HARDWARE LIST ************** #1 7-685-792-09 SCREW +PTT 2.6X6 (S) #2 7-685-105-19 SCREW +P 2X8 TYPE2 NON-SLIT #3 7-628-253-00 SCREW +PS 2X4 #4 7-627-553-37 SCREW , PRECISION +P 2X3 TYPE3 #5 7-627-553-17 SCREW , PRECISION +P 2X2 TYPE3 #6 7-627-000-00 SCREW , PRECISION +P 1.
38 Sony Corporation Mobile Electronics Division Company 9-870-139-11 CDX-1000RF 2000C0416-1 Printed in Japan ©2000. 3 Published by General Engineering Dept.
An important point after buying a device Sony CDX-1000RF (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sony CDX-1000RF yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sony CDX-1000RF - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sony CDX-1000RF you will learn all the available features of the product, as well as information on its operation. The information that you get Sony CDX-1000RF will certainly help you make a decision on the purchase.
If you already are a holder of Sony CDX-1000RF, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sony CDX-1000RF.
However, one of the most important roles played by the user manual is to help in solving problems with Sony CDX-1000RF. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sony CDX-1000RF along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
