Instruction/ maintenance manual of the product TP 100-400 Snapper
Go to page of 9
:.’ OPERATOR’S MANUAL WIDE BODY CART COLLECTOR Dual Wheel Cart For Use With Turbo Collection System Form I 708219 printed in USA l/94-1GCCI SUNSTAR/ SERIES CART SOVEREIGN/900 SERIES CART MFG.
‘in. . : :: .:.. ~,: ‘:, :.,.: ,.~.~~ ,.. :L..~ ~~: .,.: : :..
Table of Contents Page Standard Fastener Identification Chart.. ..................................................... inside Front Cover Decals ...........................................................................................................
Pa&e& with Turbo Mfg. No. 1692257 6. Hitch and Tube Assembly - SunStar Series km 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Tube Assy. (Incl. Ref. No. 38) Nut, Hex Full, Lock, #lo-32 Washer, Plain, #l 0 Screw. Phillips, Truss Head, #10-32x l/2 Hose Clamp, 6” Decal, Cleaning Inst.
Cart Assembly NOTE: Sort out the hardware and arrange by size and type. Refer to figure 1. 1. Install the wheel assemblies (A, figure 2) to the frame (B). Place the head of the swivel wheel on the end of the frame. Align the holes and place four 3/8- 16 x 1 hex bolts up through the frame and head of the swivel.
6. Install the sleeve clamp (C, figure 11) to the connect- ing sleeve (A) with l/4-20 x l/Z slotted truss head screw (D) and nyloc nut (E). Install the connecting sleeve inside the collar of the cover and position sleeve clamp (C) over the support tube (B).
Discharge Tube Installation Landlord/1700 Series (Mfg. No. 1692095) 1. Install the spring clip (D, figure 18) with two 10-32 x i/2 truss head screws (E), four flat washers (F), and two locknuts (G). 2. Install l/4-20 x 5/8 carriage bolt (H) through hole in turbo housing.
Maintenance Operation * The cart cover IS subject to wear and detenora- tion. Check the cover frequently. Use an Grass should be cut often, and not too short. If grass is too long or lush it may be necessary to keep ground speed to a minimum or to cut only half the width to pre- vent clogging.
TORQUE SPECIFICATIONS FOR STANDARD MACHINE HARDWARE TOLERANCE +20% SIZE 8-32 8-36 1 O-24 1 O-32 I/4-20 l/4-28 5/i 6-l 8 5/l 6-24 318-l 6 318-24 7116-14 7/l 6-20 l/2-13 I/2-20 9116-l 2 9/l 6-18 518-l 1 518-l 8 314-l 0 314-l 6 718-9 718-l 4 1-8 l-12 SAE GRADE #2 SAE GRADE #5 SAE GRADE #S 0 Q 8 In.
An important point after buying a device Snapper TP 100-400 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Snapper TP 100-400 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Snapper TP 100-400 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Snapper TP 100-400 you will learn all the available features of the product, as well as information on its operation. The information that you get Snapper TP 100-400 will certainly help you make a decision on the purchase.
If you already are a holder of Snapper TP 100-400, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Snapper TP 100-400.
However, one of the most important roles played by the user manual is to help in solving problems with Snapper TP 100-400. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Snapper TP 100-400 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
