Instruction/ maintenance manual of the product Clean Sweep Twin Catcher Simplicity
Go to page of 18
A TT A CHMENT OPERA T OR’S MANU AL Clean Sweep T win Catcher Mfg. No. Description 1694498 Clean Sweep Twin Catcher 1726793 Rev. 02 Rev. Date 03/2004 TP 100-4033-02-AT-SN Clean Sweep T win Catcher.
1 Initial Collector Assembl y Install Cov er & Bags ......................................13 Normal Remov al & Installation Removing the Gr ass Catcher ........................14 Installing the Grass Catcher ..........................15 Hard ware Identification & T or que Specifications .
2 Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian- gle in text signifies important cautions or warnings which must be followed.
BEFORE OPERA TION Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged.
Initial T urbo Installation 4 50" 44" 35 49 48 7 8 6 4 5 Existing Hardware (Bolt, W asher , Lockwasher , & Nut) 40 41 42 43 22 38 44 1 1 2 3 9 18 18 15 16 17 8 14 13 Existing Pulley & Spacer T orque to 55-70 ft.
Initial T urbo Installation 5 Install Deflector Hinge Assembly 1. Remove the bolts (A, Figure 2) securing the RH arbor cover, then remove the cover from the deck. Discard the cover and bolts (A). 2. Remove and discard the plastic plugs from the deck at the locations used by bolts (F & B, Figure 5).
Initial T urbo Installation 6 Install Deflector 1. See Figure 6. Drill four 13/64” holes from the bottom of the deflector at the pre-molded drill points (A, bot- tom of deflector). 2. Attach the deflector to the support rod wire-form using four #10-14 x 3/4 truss head screws and nylock nuts.
Initial T urbo Installation 7 Install Idler Assembl y & Belt Co ver 1. See Figure 9. Remove and discard the two taptite screws from locations (E). 2. Insert two 5/16-18 x 7/8 capscrews (C) through the mower deck and arbor. Tighten the capscrews. 3.
Initial T urbo Installation 8 Install Belt Cover Plate 1. Attach the belt cover plate (B, Figure 13 & 14) to the support bracket (E) using a 5/16-18 x 1 capscrew (C), washer (D) and nylock nut (F). NOTE: This cover plate must be able to pivot on the support bracket.
Initial T urbo Installation 9 Mower Dec k Arbor Pulley Mower Dec k T urbo Driv e Pulley T urbo Driv e Pulley Idler Pulleys T o Slac k en Belt CA UTION Before you begin operating the unit with the Turb.
Initial Counter Balance & W eight Carrier Installation 10 Figure 1. Counter Balance Installation Figure 2. Front Weight Carrier Installation A. Washer, 5/16 E. Clips, Safety B. Capscrew, 5/16-18 x 1 F. Carrier, Weight C. Locknut, 5/16-18 G. Holes D.
Initial Hitch & T ube Installation 11 Figure 1. Install Hitch Plate A. Hitch Plate E. Upper & Lower B. Heat Shield Bumper C. Capscrews, F. Washer 1/2-13 x 1-1/4 G. New Holes, 17/32” D. Locknuts, 1/2-13 H. Existing RH Holes Figure 3. Install Back Plate A.
Initial Hitch & T ube Installation 12 Figure 4. Assemble Tubes & Deflector A E C F B A. Upper Tube B. Middle Tube C. Lower Tube D. Nut, Nylock, 10-24 x 3/4 E. Washer F. Screw, Truss Head, 10-24 G. Holes H. Clip and Hardware Assemble T ubes & Deflector 1.
Initial Collector Assembly 13 Figure 7. Install Catcher A. Nut, #10-32 E. Hinge Pin B. Handle F. Bags C. Screw, #10-32 x 1/2 G. Hair Pin Clip D. Cover Figure 8. Install Cable A. Cable C. Washer B. Support A B C D E F G COLLECT OR ASSEMBL Y Install Cover and Ba gs 1.
Normal Removal & Installation 14 NORMAL REMO V AL & INST ALLA TION Removing the Grass Catc her 1. Disconnect the tubes (A, Figure 9) from the turbo and remove them from the catcher. 2. Remove the hair pin clip (B, Figure 9) and clevis pin (D) securing the cover (E).
Removing and Reattaching Grass Catcher 15 Installing the Grass Carc her 1. Set the back plate & support (A, Figure 11) on pins of hitch plate (C). Secure with rod (D) and hair pin (B). 2. Install the bags (C, Figure 12). 3. Install the cover (E, Figure 12).
16 T orque Specification Chart FOR ST ANDARD MACHINE HARDWARE (T olerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.
MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2004 Simplicity Manufacturing, Inc.
An important point after buying a device Simplicity Clean Sweep Twin Catcher (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Simplicity Clean Sweep Twin Catcher yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Simplicity Clean Sweep Twin Catcher - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Simplicity Clean Sweep Twin Catcher you will learn all the available features of the product, as well as information on its operation. The information that you get Simplicity Clean Sweep Twin Catcher will certainly help you make a decision on the purchase.
If you already are a holder of Simplicity Clean Sweep Twin Catcher, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Simplicity Clean Sweep Twin Catcher.
However, one of the most important roles played by the user manual is to help in solving problems with Simplicity Clean Sweep Twin Catcher. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Simplicity Clean Sweep Twin Catcher along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
