Instruction/ maintenance manual of the product M367 Shure
Go to page of 11
Model M367 User Guide ©2008 Shure Incorporated 27C851 1 (Rev . 5) Printed in U.S.A. SIX CHANNEL MICROPHONE MIXER DESCRIPTION The Shure M367 is a portable, six - input, two-output (mono), battery-powered microphone and line level mixer/p reamplifier .
2 FRONT PANEL CONTROLS AND INDICATORS FRONT PANEL CONTROLS AND INDICATORS FIGURE 1 1. Input Gain Control : For best performa nce, adjust each Input Gain Control so the associate d Input Peak LED illuminates red only on the loude st signal peaks. 2. Input Low-Cut Filte r Switch: Provides low-frequency roll – off to reduce wind noise and rumble.
3 REAR PANEL CONNECTORS AND CONTROLS REAR PANEL CONNECTORS AND CONTROLS FIGURE 2 1. Mic/Line Level Output Switch: Sets output to mi crophone or line level. 2. Phantom Power Switch: Adds 12-volt phantom power to all inputs set to MIC. Use DIP swit ch 7 to increase voltage to 48 volts (see DIP Switches).
4 AC OPERA TION Use the supplied powe r adapter to connect the M367 to a power outlet. M367: 100-120 V AC, 50/60 Hz M367E: 220-240 V AC, 50/60 Hz The operating voltage can be switched internally (see In ternal Modifiable Functions ).
5 SPECIFICATIONS Frequency Respo nse 20 to 20,000 Hz ± 2.0 dB (channel controls centered) Total Harmoni c Distortion 0.25% THD at +4 dBm output, 55 to 20,000 Hz Voltage Gain Inputs Outputs Equivalent.
6 REPLACEMENT P ARTS Foot Kit (4 in kit) ............. ............ .............. ........... ......... 90S8100 M367 Fuse, 0.125 A, 250 V .......... ............................ ..... 80E380 M367E Fuse, 0.063 A, 250 V ..... ...................... ...
7 INTERNAL ADJUSTMENTS These internal ad justments require only removal of the top cover: 1. Remove battery compartment. 2. Remove four screws securing two plastic end caps and one ground-bonding screw on the side opp osite the battery com- part ment.
8 INTERNAL MODIFIABLE FUNCTIONS Perform all modifications through solder points accessible on the main PC board. DISASSEMBLIN G THE M367 1. Remove the mixer top cover as previously descri bed. 2. Carefully remove three multi -pin cable assembly conn ectors from upper front PC board (nearest front panel).
9 ADAPTING LINE OUT TO DUAL BANANA JACK Add a dual banana j ack, balanced, line-level o utput capability by purchasing a commercial unit (Sescom XLR F-3BP or equivale nt), or obtaining a female XLR co.
10 CHANGING LIMITER RELEASE TIME TO ONE SECOND Remove resistor R741 (about 15 mm behin d ribbon cable assembly W813). CHANGING LIMITER THRESHOLD PRESETS 1. Select the equivalent resistor values for the desired limiter thresholds from the following table.
SHURE Incorporated http:/ /www.shure.com United States, Canada, Latin America, Caribbean: 5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A. Phone: 847-600-2000 U.
An important point after buying a device Shure M367 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Shure M367 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Shure M367 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Shure M367 you will learn all the available features of the product, as well as information on its operation. The information that you get Shure M367 will certainly help you make a decision on the purchase.
If you already are a holder of Shure M367, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Shure M367.
However, one of the most important roles played by the user manual is to help in solving problems with Shure M367. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Shure M367 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
