Instruction/ maintenance manual of the product SCN48 Senco
Go to page of 12
NFD84U5J - Issued: February 14, 2008 © 2008 by Senco Products , Inc. Operating Instructions Instr ucciones de Operacion Mode d’Emploi Q u e s ti o n s? C om m e nt s ? c al l SE N C O’ S to l l -f r e e A c ti o n -l i ne : 1- 8 0 0- 5 4 3- 4 5 96 o r e - ma i l : t o ol p r of @ s en c o .
2 T ABLE OF CONTENTS T ool Use 2 Maintenance 6 T roub leshooting 7 Specications 8 Accessories 9 T ABLA DE MA TERIAS Uso de la Herramienta 2 Mantenimiento 6 Identicación de F allas 7 Espec.
3 English Español Français T ool Use Uso de la Herramienta Utilisation de l’Outil Inser trstnailintodrivertrac k with second nail into the feeder pawl. Inser te el primer clavo en el riel con el segundo clav o dentro del trinquetedealimentación.
4 English Español Français T ool Use Uso de la Herramienta Utilisation de l’Outil Extract bent nail from rear of guide body . Extraiga el clav o doblado des- de atrás del cuerpo guía. Extirper le mauvais clou par l’arriéré du front. Press down on the gate latch and lift open gate.
5 English Español Français T ool Use Uso de la Herramienta Utilisation de l’Outil These tools hav e an adjust- able trigger and can be set for Contact Actuation or Sequential Actuation. Press the button on the side of the tool as shown and rotate to the desired setting.
6 English Español Français Maintenance Mantenimiento Entretien Squir t Senco pneumatic oil (5 to 10 drops) into the air inlet twice daily . (Depending on frequency of tool use.) Other oils ma y damage O-rings and other tool par ts. Aplique aceite neumático Senco en la entrada de aire dos veces al día.
7 W ARNING Repairs other than those described here should be performed only by trained,qualiedpersonnel. Contact SENCO for inf or mation at 1-800-543-4596. ALERT A Las reparaciones, fuera de aquellas descritas aquí, deben de ser llev a- das a cabo solamente por personal entrenadoycalicado .
8 2,1mm SE English Español Français Specifications Especificaciones Specifications 1 3/4” 1 1/2” 1 1/4” .082” GD 2,9m m 2” 2 1/4” 2 1/2” .
9 English TECHNICAL SPECIFICA TIONS Min to max operating pressure Air Consumption (60 cycles per minute) Air Inlet Maximum Speed (cycles per second) Weight Nails per Magazine Capacity Nail Lengths Nai.
Limited Warranty SENCO® Pneumatic, DuraSpin®, Cordless Tools & Compressors Senco Products, Inc. (“SENCO”) designs and constructs its products using the highest standards of material and workmanship.
THIS P AGE INTENTIONALL Y LEFT BLANK Limited Warranty SENCO® Pneumatic, DuraSpin®, Cordless Tools & Compressors Senco Products, Inc. (“SENCO”) designs and constructs its products using the highest standards of material and workmanship.
THIS P AGE INTENTIONALL Y LEFT BLANK.
An important point after buying a device Senco SCN48 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Senco SCN48 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Senco SCN48 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Senco SCN48 you will learn all the available features of the product, as well as information on its operation. The information that you get Senco SCN48 will certainly help you make a decision on the purchase.
If you already are a holder of Senco SCN48, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Senco SCN48.
However, one of the most important roles played by the user manual is to help in solving problems with Senco SCN48. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Senco SCN48 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
