Instruction/ maintenance manual of the product BN200V12 Porter-Cable
Go to page of 19
CORDLESS BRAD NAILER Instruction manual The Model and Serial No. plate is located on the magazine of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No.
GENERAL SAFETY RULES WARNING: When using pneumatic tools, basic safety precautions should always be followed to reduce the risk of personal injury. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.
3 9. THE TOOL COMES EQUIPPED WITH TWIN POWER SOURCE TECHNOLOGY (TPS) ™ . DISCONNECT TOOL FROM AIR SUPPLY HOSE AND/OR REMOVE BATTERY before doing tool maintenance, clearing a jammed fastener, leaving work area, moving tool to another location, handing the tool to another person, or making adjustments.
4 1 7. REMOVE FINGER FROM TRIGGER when not driving fasteners. Never carry tool with finger on trigger. Fig. 10. 1 8 . DON’T OVERREACH. Keep proper footing and balance at all times when using or handling the tool. 1 9 . FIRE FASTENERS INTO WORK SURFACE ONLY: never into m aterials too hard to penetrate.
5 WORK AREA 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
6 7. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. 8. Use only accessories that are recommended by the manufacturer for your model.
7 2. Before using a battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery pack, and (3) product using battery. 3. CAUTION: To reduce risk of injury, Porter-Cable charger should only be used to charge Porter-Cable battery pack.
8 1 9. Dispose of expended batteries properly. Porter-Cable Battery Packs contain rechargeable, nickel-cadmium batteries. These batteries must be recycled or disposed of properly.
9 All compressed air contains moisture and other contaminates that are detrimental to internal components of the tool. When using external air, an air line filter will remove most of these contaminates and significantly prolong the life of the tool.
OPERA TION USING THE TOOL Complete all steps of PREPARING THE TOOL before using the tool. To fasten, move switch (A) Fig. 19 to desired position, grip tool firmly, position nose of tool onto work surface, push forward on tool to depress safety, and squeeze trigger to fire a fastener while allowing tool to recoil.
11 WARNING: Disconnect tool from air supply and/or remove battery before performing maintenance, clearing a jammed fastener, leaving work area, moving tool to another location, handing the tool to another person, making adjustments. WARNING: Clean and inspect tool daily.
12 CLEARING A JAMMED F ASTENER 1. WARNING: Disconnect tool from air supply and/or remove battery. 2. Open magazine and remove any remaining fasteners (see Fig. 16). CAUTION: Remove fasteners from tool before opening the fastener guide plate. Fasteners are under pressure and may shoot out of magazine which could cause injury.
13 BA TTER Y OPERA TION CHARGING THE BA TTERY P ACK GENERAL Before using your cordless Nailer for the first time, the battery pack should be fully charged. If the battery pack is installed in the Nailer, remove it by following instructions under INSTALLING OR REMOVING BATTERY PACK.
14 DIAGNOSTICS The Porter-Cable Charger is equipped with a diagnostic system that automatically checks the battery pack each time a pack is inserted into the charger. If no problems are found, the charger will automatically switch to “Fast Charge” mode as described in NORMAL CHARGING.
MAINTENANCE CLEAN AND INSPECT DAIL Y WARNING: Disconnect tool from air supply and/or remove battery before cleaning and inspection. Correct all problems before placing the tool back in use. Wipe tool clean and inspect for wear or damage. Use non-flammable cleaning solutions to wipe exterior of tool only if necessary.
TROUBLESHOOTING WARNING: Disconnect tool from air supply and/ or remove battery before performing any Service Procedure. SYMPTOM PROBLEMS SOLUTIONS 1. Air leak near top of Loose screws. Tighten screws. tool or in trigger area. Worn or damaged Install Overhaul Kit.
17 PORTER-CABLE LIMITED ONE YEAR W ARRANTY Porter-Cable warrants its nailing and stapling tools for a period of one year from the date of original purchase.
18 NOTES 901891 - 08-31-01.qxd 2/13/02 11:53 AM Page 18.
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE .
An important point after buying a device Porter-Cable BN200V12 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Porter-Cable BN200V12 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Porter-Cable BN200V12 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Porter-Cable BN200V12 you will learn all the available features of the product, as well as information on its operation. The information that you get Porter-Cable BN200V12 will certainly help you make a decision on the purchase.
If you already are a holder of Porter-Cable BN200V12, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Porter-Cable BN200V12.
However, one of the most important roles played by the user manual is to help in solving problems with Porter-Cable BN200V12. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Porter-Cable BN200V12 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
