Instruction/ maintenance manual of the product 9-29012 Sears
Go to page of 20
SFo _u_h_ '_e"_r"unle _ SWA/_S owner's manual CATALOG NO. 9-29012 9-29013 FITS THE FOLLOWING MODEL NUMBERS: 113.197110, 113.197111 113.197150, 113.197151 113.197210, 113.197211 113.197250, 113_197251 113.197410, 113.197411 113.197510, 113.
Table of Contents Section Title ................................................................................ Page Safety ........................................................................................................................ 3 Assembly .
Safety This manual has safety information and ins_ctions to help users eliminate or reduce the risk of accidents and injuries, including: 1. Severe cuts, and loss of fingers or other body parts due to contact with the blade. 2. Eye impact injuries, and blindness, from being hit by a thrown workpiece, workpiece chips or pieces of blade, 3.
Safety Kickback Hazard Kickback is the uncontrolled p_opelling of the workpiece back toward the user' during ripping° The cause of kickback is the binding or pinching of the blade in the workpiece° Several conditions can cause the blade to bind or pinch.
Safety Instructions Read and follow all safety instructions, Personal Safety Instructions 1. Wear" safety goggles labeled "ANSI Z87.1" on the package, tt means the goggles meet impact standards set by the American National Standards Institute.
Safety Saw Safety Instructions 1_ Use guard, pawls and riving knife accord- ing to instructions. Keep them in working order. 2_ Routinely check saw for broken or dam- aged parts. Repair or replace damaged parts before using saw. Check new or rep_ed parts fbr alignment, binding, and correct installation.
Safety 3. Rip only workpieces longer than the diameter of the blade. Do not rip workpieces that are shorter than the diameter of the blade being used. 4. Workpieces that extend beyond the saw table can shift, twist, rise up from the table, or fall as they ar'e cut or afterwards.
Assembly Identify Parts 3he h_!lowing paris are inchided: Nole: B@nv beginning assembl3; check that all parts are included If you ate missing at O, part, do m_t assemble guar_L _mtact your Sear_ Service Center to get the missing part. Sonlethnes snlall parts can get lost in packaging material.
Assembly Guard Installation Steps 1. Remove existing table boards. Keep all screws, nuts and washers, including the lev- elling screws in the center of the front table.
Assembly 7, Rotate the saw to the negative 45 degree l_'cx,_c! position. Remove and discmd ttle oflmr lmndle retaining screw, Discard tile old handle, 8. Using the two #1(1 x 3/4 flat head screws provided, altach the new h;mdle in tile same way as the old one was renloved, 9o Return lhe saw to the blade vertical, cross- cut position.
Alignment Align Riving Knife to Blade The goa! of this adjustment is to position the riving knife directly in line with the blade. Riving knife alignment is an important safe- ty factor, The riving knife rides in the kerf of the cut work_iece during ripping to keep the two sides of the workpiece from pinching on the blade.
Controls Miter Lock Yellow Ke Bevel Lock dwheel Miter Lock On-Off Switch Yellow Key Bevel Lock Handwheel %ble Lock (Cabinet Model -Not Illustrated) Function Frees radial arm to move; locks in any desi.
Controls Rip Scale & Rip Lock Rip lnd'_a,ors .__ 0 _-._.,._ Swivel Lock l Table Clam[ 11" Thumbscre_ t Control Function Operation/Comments Rip Lock Frees carriage to move along radial tu.
Controls Control Guard Clamp Screw Guard llold Down Knob tlokt Down Riving Knife Bracket Function Secures guard to motor; frees guard for removal Protects against contact with upper blade; partially p.
Controls Pawls Riving Knile Knob Pawls Riving Knife Control G u ard Tab Pawls!Riving Knife Knob Pawls Riving Knife Function Provides manual way to raise clear plastic guard during rip- ping when work.
Notes 16.
PARTS LIST CRAFTSMAN 10" RADIAL SAW GUARD KIT CATALOG 9-29012 & 9-29013 Always order by Part Number - Not by Key Number Key No ! 2 3 4 5 6 7 8 9 t0 11 12 13 14 15 1 Part No.
28 8 9 31 PARTS LIST CRAFTSMAN 10" RADIAL SAW GUARD KIT CATALOG 9-29012 & 9-29013 Always order by Part Number - Not by Key Number 1 33 / 34 35 33 3O 24 1 27 17 16 2O FIGURE 2 10 11 14 13 7 6 .
c£) PARTS LIST CRAFTSMAN 10" RADIAL SAW GUARD KIT CATALOG 9-29012 & 9-29013 Always order by Part Number - Not by Key Number FIGURE 2 - GUARD Key Pa_ No .
owner's manual SERVICE CATALOG NO. 9-29012 9-29013 The model number of your drill press is found at the rear of the head When requesting service or ordering parts, always pro- vide lhe following .
An important point after buying a device Sears 9-29012 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sears 9-29012 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sears 9-29012 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sears 9-29012 you will learn all the available features of the product, as well as information on its operation. The information that you get Sears 9-29012 will certainly help you make a decision on the purchase.
If you already are a holder of Sears 9-29012, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sears 9-29012.
However, one of the most important roles played by the user manual is to help in solving problems with Sears 9-29012. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sears 9-29012 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
