Instruction/ maintenance manual of the product FXCD-500 Sanyo
Go to page of 31
OPERATING INSTRUCTIONS FXCD-500 Full Panel Detachable FM Stereo/AM Receiver Auto Reverse Cassette Player Compact Disc Player with CD Changer Controller IS0 Mounting with Removable Trim Ring (English) .
SANYO MOBILE AUDIO MODEL FXCD-500 LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Factory Service Center at th.
CONTENTS COMPACT DISC CARE 3 DIGITAL DISPLAY 5 DETACHABLE FRONT PANEL 6 GENERAL OPERATION 7 RADIO OPERATION 9 TAPE OPERATION 11 CD OPERATION 14 CD CHANGER OPERATION 16 ERROR SIGNS 16 CLOCK 19 HINTS FO.
COMPACT DISC CARE Dirt, dust, scratches and warpage can cause a deterioration in the sound or intermittent skipping some tracks during play f DIGITAL AUDIO l This unit has been designed to play compac.
l Never use chemicals such as record clean- ing sprays, antistatic sprays or fluids, ben- zene or thinner to clean compact discs These chemicals will permanently damage the plastic surface of the disc.
DIGITAL DISPLAY Automatic Music Select System (AMSS) Metal Display Auto Travel Preset (ATP) Tape playing direction Disc in BASSXPANDER Dolby Noise Reduction Disc Number FM Bands Radio Frequency, Time,.
DETACHABLE FRONT PANEL The front panel is designed to be removable for antitheft purposes It is recommended that you remove and carry the front panel with you when you leave your car A carrying case i.
GENERAL OPERATION 4 8 765 i 2 3 TURNING THE POWER ON install the front panel and press the ON/OFF button 0 when ACC is on TURNING THE POWER OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Press the ON/OFF button 0 to stop the current operation The button dims when the power is off (ACC on) ELECTRONIC CONTROLS .
ELECTRONIC CONTROL RESET Press the SEL button 0 for about 3 seconds until the unit beeps, the audio controls, except for vol- ume, will be reset BASSXPANDER (BASX) - l/2 .
RADIO OPERATION I I I I I I I 3 SELECTING RADIO MODE Press the BND button 0 to switch from tape, CD or CD changer* mode to the radio Each time the BND button is pressed, the selected band changes as shown below * If a CD changer is connected FM1 - FM11 - AM RADIO TUNING .
ATP (AUTO TRAVEL PRESET) OPERATION . . . . . . . . . . . . . . 4 The Auto Travel Preset function searches for and memorizes the 6 strongest stations in one of the two bands (FM I, AM) in order of sign.
TAPE OPERATION 109876 LOADING AND EJECTING THE TAPE Insert a cassette into the tape slot 0 and the tape player will start Press the eject button 0 to eject a tape The system will return to the last mo.
LOCATING THE BEGINNING OF A PROGRAM (AMSS) . . . . 4,5,6 This system is equipped with a function that allows you to skip forward or backward to locate the beginning of a particular selection on the ta.
SCAN MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Scan helps to find a program by playing about the first 10 seconds of each selection ’ Press the SCN.
CD OPERATION LOADING AND EJECTING THE CD . . . . . . . . , . , . . . . . . . . . . . 1, 2 insert a disc into the CD slot 0 and the CD player will start Press the eject button 0 to eject a disc pm CAUT.
SKIPPING TRACKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495 Press the TRACK $ button 6% to skip to the beginning of the next track Press the TRACK 0 button 0 to skip .
CD CHANGER OPERATION THE UNIT CAN BE USED TO CONTROL THE FUNCTIONS OF THE AX-300, AX-500 OR OTHER COMPATIBLE SANYO CD CHANGERS 54 1 67832 SELECTING CD CHANGER MODE .
REPEATMODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 l Repeat tracks Press the RPT button 0 to play the current track repeatedly l Repeat discs Press the RPT bu.
CD Player If a problem should occur while operating the built-in CD player, one of the following error signs may be displayed Error Sign Jf J7 I J, J,( 1 Cause Abnormal mechanism function Remedy Press.
CLOCK 32 1 DISPLAY MODE CHANGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 The display on the unit can be changed by pushing button 0 Press the DISP button 0 to switch between the .
HINTS FOR PROPER AND SAFE OPERATION l Condensation Moisturecan condense on the optical lens of the CD player during humid or rainy days, or after the car heater is turned on If this occurs the disc pl.
TROUBLESHOOTING Sometimes a simple operational error or a mistake in the wiring can appear to be a problem with the unit Before having the unit serviced, refer to the troubleshooting chart below Sympt.
ACCESSORIES AND HARDWARE INSTALLATION Mounting Bracket Rear Strap (Half Sleeve) x 1 (Brace) x 1 Screw M5 x 14 x2 Hex bolt M8 x 6 x4 MountingGrommet Xl Mounting Screw M5 xl SECURITY OF FRONT PANEL Remo.
INSTALLATION 1. BEFORE INSTALLATION When mounting the unit in a car, keep the unit as level as If the unit must be mounted at an angle, due to the design of the vehicle, make sure the unit does not tilt by more than 30” 2.
3. INSTALLATION PROCEDURES 1) Installation with Mounting Kit DASHBOARD TRIM RING DASHBOARD OR CONSOLE MOUNTING SCREW TRIM 1 Inset-t the mounting bracket into the DIN-standard cutout (182 x 53 mm) in t.
2) Installation to TOYOTA/NISSAN Vehicles Install the unit using the existing TOYOTA/NISSAN Mounting Bracket and Screws Use the mounting holes in the unit chassis ‘7” or “N” is engraved next t.
UNIT REMOVAL UNLOCK LEVERS 1 Remove the front panel by pressing the release knob 2 Insert the unlock levers into the slots as illustrated r Note The jagged side of the key should face outward 3 Slide .
ELECTRICAL CONNECTIONS I-- - - - P-speaker System - - - I (Ga : (Gray/Bl& 0 (Green) i (Green/Bw I (vi- i (Violet/Black)B - - - - - - - - + 12V Constant Power Supply (Yellow) 3 -I- 12VAccessoryDwi.
Notes l When using a two-speaker installation, the Green, Green/Black, Violet, violet/Black wires, which are used for a four-speaker installation, are not used The ends of these wires must be covered .
FM TUNER SECTION Frequency Range 87 5MHz - 107 9MHz Usable Sensitivity 15dBf 50dB Quieting Sensitivity 30dBf Frequency Response ( f 3dB) 50Hz - 12 5kHz I F Rejection 1 OOdB Image Rejection 65dB Signal.
AUDIO SECTION RMS Power Rating (3% THD) RMS Power Rating (10% THD) Maximum Output Power Load Impedance GENERAL Operating Voltage Operating Current Maximum IMPORTANT INFORMATION 2OWx4 (144V) 24Wx4 (144.
An important point after buying a device Sanyo FXCD-500 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sanyo FXCD-500 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sanyo FXCD-500 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sanyo FXCD-500 you will learn all the available features of the product, as well as information on its operation. The information that you get Sanyo FXCD-500 will certainly help you make a decision on the purchase.
If you already are a holder of Sanyo FXCD-500, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sanyo FXCD-500.
However, one of the most important roles played by the user manual is to help in solving problems with Sanyo FXCD-500. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sanyo FXCD-500 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
