Instruction/ maintenance manual of the product FM/AM/TV/WEATHER 4 Band Reviever Sangean Electronics
Go to page of 17
.
1 5 3 6 7 8 9 11 12 13 14 2 4 10 2.
3 Location Of Controls W elcome to SANGEAN W orld of Listening. To ensure proper operation please familianrize yourself with These instructions before using your new receiver.
1 2 3 4 5 6 7 8 9 A B C D E F I J K L 4 G H.
5 Display Icons Band Selected/ PM---------------------------------------------------------- Timer / (Alarm)-------------------------------------------------------------- FM Stereo lndicator-----------.
Battery Installation The battery cover is located on the back of the unit. Slide the cover in the direction of the arrow to gain access to the battery compartment insert 2 AAA(UM-4) batteries into the compartment.Make sure that batteries are positioned in accordance with the diagram located below batteries in battery compartment.
7 3 8 13 14 8 8 Setting Time When batteries are installed for the first time the LCD display time digit will flash indicating that the time needs to be set. The clock can be set with the power off but the lockswitch must be off. T o set time press Time Set Button for more then 2 seconds until hour digit flashes.
8 13 14 14 9 9 LCD will return to real time and Standby Set icon will appear in display . A buzzer will sound when set time is reached and will continue for at least 3 mimutes or until it is stopped by pressing the Power On/Off Button. Short T erm Alarm Set This receiver is equipped with a short term 1-180minute timer.
9 RADIO OPERA TION Antenna/Earphone Use The earphone cord acts as an antenna during reception of FM/TV/Weather Band(DT -300/300V/300VW)channels and should be extended as much as possible to improve sensitivity . Insert the earphone into the earphone jack for earphone operation .
V olume Control The volume may be adjusted by using the V olume Control Adjustment T uning the Radio Band Frequency Antenna AM 520-1710kHz/ Internal-Rotate radio for best 522-1629kHz reception FM 87.5-108MHz External-Make sure earphone or pig tail antenna is inserted into earphone jack.
WX CH.0-9 External-Make sure earphone or pigtail antenna is inserted into Earphone jack A.Scan T uning Turn on the radio by pressing On/Of f Button . Select the desired band by pressing Band Selection Button Press and hold the Tuning Control Button or for more than 1/2 second .
12 13 14 5 11 8 11 13 14 until the desired station is reached or pressing and holding the T uning Control or until the station is reached. C. Setting Presets Manually Turn on receiver by pressing On/Of f Button .Select desired band by pressing Band Selector Button .
13 11 11 5 8 12 13 14 station is selected to take its place. When the memory is full for a particular band pressing the Memory Selection Button will cause all the positions to flash. In this case,select the desired position. press the Memory Selection Switch and the original station will be eliminated and the new station will take its place.
5 8 11 12 11 5 8 On/off Button .Select desired band by pressing Band Select or Button . Press Memory Button . Memo will flash in display. Press Select Button for move than 2 seconds until auto/memo appears and flashes in display. press memory Button again.
15 Note: If the Select Cursor points at the frequency the Tuning Control Up/Down Button will continue to change frequency within the band selected. If the Selector Cursor points at the position digits for the memory presets the Tuning Control Up/Down Button and will select the memory presets.
16 9 7 3 3 Mono/Stereo Button Monaural or Stereo headphone reception may be selected durning FM reception by alternately pressing the Mono/Stereo Button The Speaker On/OffSwitch must be in the Off Lock Switch To Prevent accidental changing of any of the radio settings move the Look Switch to the locked position.
Specification T ype: FM- Stereo (Via earphone) AM- Standard (mono) TV Band (Mono Ch,2-13 VHF) DT -300V/VW W eather Band (WX) (Mono Ch. 0-9) DT -300VW Earphone jack: 3.5 mm mini-plug 16 or 32 ohm impedance (Stereo) Output Power: 50 mW (10 THD) via built-in speaker Speaker: 1.
An important point after buying a device Sangean Electronics FM/AM/TV/WEATHER 4 Band Reviever (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sangean Electronics FM/AM/TV/WEATHER 4 Band Reviever yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sangean Electronics FM/AM/TV/WEATHER 4 Band Reviever - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sangean Electronics FM/AM/TV/WEATHER 4 Band Reviever you will learn all the available features of the product, as well as information on its operation. The information that you get Sangean Electronics FM/AM/TV/WEATHER 4 Band Reviever will certainly help you make a decision on the purchase.
If you already are a holder of Sangean Electronics FM/AM/TV/WEATHER 4 Band Reviever, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sangean Electronics FM/AM/TV/WEATHER 4 Band Reviever.
However, one of the most important roles played by the user manual is to help in solving problems with Sangean Electronics FM/AM/TV/WEATHER 4 Band Reviever. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sangean Electronics FM/AM/TV/WEATHER 4 Band Reviever along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
