Instruction/ maintenance manual of the product DT-110 Sangean Electronics
Go to page of 18
.
FM STEREO/AM PLL SYNTHESIZED RECEIVER TUNING MO./ST. BAND DT 110 DBB Vol. DBB On Off Lock 2 3 4 7 8 10 9 5 11 12 13 14 1 2 6.
3 LOCA TION OF CONTROLS To insure proper operation, please familiarize your - self with these instructions before using your new receiver. . On/Off button . LCD display . T uning Control Down . T uning Control Up . Battery Compartment . Memory Button .
4 FM Stereo indicator System lock Low battery indicator Memory Presets Band Selected 90 minutes auto shut off Frequency Auto Scan /Memory Scan status Frequency unit ST AUTO MEMO SCAN AUTO MEMO SCAN Mh.
5 BA TTERY INST ALLA TION The battery cover is located on the back of the unit. Slide the cover in the direction of the arrow to gain access to the battery compartment . Insert 2 AAA (UM-4) batteries into the compartment. Make sure that the batteries are positioned in accordance with the diagram indicated.
6 ANTENNA/EARPHONE USE VO LUME CONTROL TUNING THE RA DIO Inserting the earphone into the earphone jack . The cord connecting the earphone to the receiver acts as an antenna during FM reception and shou- ld be extended as much as possible to increase FM sensitivity .
7 Pho ne is inserted into earph- one jack. A . APS (auto scan and auto pre set) This radio equips with APS device to have auto scan and auto preset function.
8 on A M band. When A PS completes , it will appear the first radio station it finds. T o recall the stations , please refer to Memory T uning (station recall ) descri bed later .
9 1 10 3 4 2 6 1 10 D . Manual T uning Tu rn on the radio by pressing On/Off button , select A M or FM band by pressing Band Selec- ted button . Desired station may be selected by pressing the Tuning Control or interm - ittently until the desired station is reached.
10 desired memory position by pressing T uning Con- trol or to the desired memory position, then press Memory button again. 'M' will stop flashing indicating station memory being done.
on FM band and M6 on AM band. F . Priority T o store your favorite stations so that you may recall the stations in a more easy way . When the desired stations are found by the tu- ning methods described above. Press the memo- ry butt on , then Prio rity stat ion butt on .
12 ed button then Memory Recall button Select the required memory station by pressing Tuning Control or , LCD display Mand memory digit will flash . Whe n the required sta- tion is found, press Memory Recall button ag- ain, LCD M and memory digit will stop flashing.
mory stations .Recall the memory stations by pre- ssing Memory Recall buttons . Press Memo- ry button for more than 2 seconds untill LCD display DEL flashing, press Memory button again, the recall memory station is then deleted.
Example : T o exchange Memory station 2 with Memo ry station 4. Recall Memory station 2 by pressing Memory Recal l button , press Memory button then Tun ing Control UP butt on to the required Me- mory station 4, then press Memory button again Memory station 2 and Memory station 4 now is exchanged.
tuning step is 10 kHz. On other countries is 9 kHz. To change AM band tuning step, please follow below steps. 1. change AM band tuning step from 9 kHz to 10kHz. Turn off the power by pressing On/Off button , press Tuning Control button Up conti- nuously then turn on the power by pressing On/Off button again.
M . Lock Switch To prevent accidential changing of any of the ra- dio settings, move the Lock Switch to up po- sition, LCD display icon will appear . T o relea- se, simply move the switch to its down position.
Earphone Jack : 3.5 mm mini-plug 32 ohm impedance (stereo) Output Power : 5 mW(10% THD) via earphone. External Power : Earphone AM 30 mA FM 40 mA Batteries : 3 V olts , AAA size (UM-4)X 2 Dimension ( WXHXD ) in mm : 9 5 x 6 0 x 2 0 Weight : 90g without batteries.
2.Use and store your radio only in normal temper- ature environments. High temperature can shor- ten the life of electronic devices, damage batte- ries and melt plastic parts. 3. Handle the radio gently and carefully. Dropping it can damage circuit boards and cases and ren- der it defective.
An important point after buying a device Sangean Electronics DT-110 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sangean Electronics DT-110 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sangean Electronics DT-110 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sangean Electronics DT-110 you will learn all the available features of the product, as well as information on its operation. The information that you get Sangean Electronics DT-110 will certainly help you make a decision on the purchase.
If you already are a holder of Sangean Electronics DT-110, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sangean Electronics DT-110.
However, one of the most important roles played by the user manual is to help in solving problems with Sangean Electronics DT-110. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sangean Electronics DT-110 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
