Instruction/ maintenance manual of the product CT-3200 Autostart
Go to page of 21
Please note: Button Ι is for the LOCK/UNLOCK functions . Button ΙΙ is for the START/STOP functions. Buttons Ι & ΙΙ (together) is for the TRUNK release function.
P. 2 Installation Guide CT-3200 Introduction This guidebook c ontains all informatio n pertinent to the inst allation. Most (if no t all) features are grouped in the user guidebo ok and therefor e, should yo u need informat ion on a featur e, you should refer to the user g uidebook.
CT-3200 Installation Guid e P. 3 order to avoid hav ing to get out of the vehicle and pressing the hood-pi n switch. The PAB will work only when the hood is up. ♦ inspect vehicle for any bo dy damage or electrical problem s ♦ always solde r and tape all connec ti ons .
P. 4 Installation Guide CT-3200 C RED (+) 12 V Battery Connect to the lar gest 12 V s upply wire at th e ignition harn ess. Ensure that the OEM power wire is fus ed for more than 30 A. NOTE: certain new vehicles hav e no suitable 12 volts source at the IGNITION switch (the 12 Volt wire is too sm all to supply th e necessary current).
CT-3200 Installation Guid e P. 5 There is also a negative p arking light output. Only one of these two different outputs needs to b e connected. 12-Pin Accessories Harness Wire Function Description 1 BLUE (–) AUX 3 ( Trunk) output 500 ma negative output.
P. 6 Installation Guide CT-3200 are pressed if the trunk pin stat e is unchanged (th e trunk was unopened) . Disarm is sen t only if the system was previo usly locked and armed.
CT-3200 Installation Guid e P. 7 starter motor while the glow-plug indi cator light is still on. The module will e ngage the starter motor as soon as the glow-plug li ght (+) goes out. • Minimum waiting time is 3 seconds. • Maximum waiting time is 25 seconds (appr ox).
The Programming Assistance Button (a.k.a. PAB.) The PAB is located on the side of the module. This pu sh button mimic s the hood-pin switch in order to av oid having to get out of the vehicle and pres sing the hood-p in switch. The PAB will work only when the hood is up.
CT-3200 Installation Guid e P. 9 Button Ι for Option 1, Button ΙΙ for Option 2, Buttons Ι & ΙΙ for Option 3. Table 3 Programming Options MODE 1 (* indicates default setting) FUNCTION 1 – I.
P. 10 Installation Guide CT-3200 This process can be carried out ins tead of the co nventional tach pr ogramming proc edure. 1. Make sure all t he connections are done properly an d that the Modul e has been powered-up. 2. With the Hood up (Ground on the Hood Pin line), s tart the vehicle using the key.
8. Idle Mode: Make s ure the vehicle pr operly goes into Idle Mode. Most comebacks are the result of misunderstandings about how a produc t works or performs. Take the time to pro perly explain all functions and features to the customers before they l eave the premises.
P. 12 Installation Guide CT-3200 seconds after shutdown, Sec ure Lock will re-lock all Doors once more ( arming the system again). Please note that most OEM systems will not rearm t he Alarm while th e Engine is run ning, but will lock the Doors.
CT-3200 Installation Guid e P. 13 Troubleshooting Poor Transmitting Range installed at lea st 7.5 cm (3 in.) from th e he best location . Install the antenna as far oise, airports, 12. vehicle ca n affect rang e as well; v ans in gener al have an especially or ran e signal from t he remote control).
P. 14 Installation Guide CT-3200 − It always better to strip more th an you need, than not enou gh. A common way cold solder joints happen is when not e nough plastic is stripped off the vehicl e's wire, so during the sol dering process the plastic from the wire mel ts and flows in to the connec tion instead of th e solder.
CT-3200 Installation Guid e P. 15 − When all of the wires hav e been connected, s older the connec tions. When the sol der has cooled, the conne ctions are then i ndividually tape d up, to isolate th em. − Return to the engi ne bay and route the start modul e wires to their corres ponding connecti ons.
P. 16 Installation Guide CT-3200 87A: Normally Closed ( N/C ). Wh en the coil is at res t, 87A is connected t o 30. 30: Common. Wh en the relay is a t rest, 30 is conn ected to 87A, when t he coil is energize d, it is then moved and makes contact wit h 87.
CT-3200 Installation Guid e P. 17 The vehicle circuits are Iso lated for a reason, the wi ring of the remote star module should reflect this.) The relay connections: 85: Connects in parall el to the Ignitio n 1 output from the remote start mod ule. This becomes the pos itive side of t he coil.
P. 18 Installation Guide CT-3200 Solution: A relay is used to inv ert the negative signal from the st art module to a p ositive signal before it is sent to the OEM switch. The relay connections: 85: Connects to the st art module's Trunk release output wir e.
CT-3200 Installation Guid e P. 19 30 : Connects to the vehic le's Trunk releas e wire. Comments : At rest the rel ay is not active and the vehicle' s Trunk release sw itch is allowed to operate normally. When the Trunk release b utton is pressed on the re mote control, the start module's Trunk release outpu t activates the re lay.
P. 20 Installation Guide CT-3200 The entire process should t ake less than 20 secon ds. 2. The car won't start by remote. • Does the light on t he remote light up when you press th e button? • Is the starter in val et mode? • Does the vehicle have passive antitheft security (PATS , VATS, PASSLOCK, TRANSPONDER)? 3.
CT-3200 Installation Guid e P. 21 16. The car doesn't s tart and the park lights flash 4 times. • Check brake circui t. • Check for blown rear p ark light (feedback ). 17. The vehicle runs for 8 seconds t hen shuts down. I have 12 volt s on starter wire the whole time but no over crank.
An important point after buying a device Autostart CT-3200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Autostart CT-3200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Autostart CT-3200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Autostart CT-3200 you will learn all the available features of the product, as well as information on its operation. The information that you get Autostart CT-3200 will certainly help you make a decision on the purchase.
If you already are a holder of Autostart CT-3200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Autostart CT-3200.
However, one of the most important roles played by the user manual is to help in solving problems with Autostart CT-3200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Autostart CT-3200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
